ASAkira Saito

Akira Saito

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Akira Saito has a total of 59 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Short-time dynamic mode decomposition: a data-driven forced response analysis of nonlinear systems under swept-sine excitation

    by Hideaki Namiki, Akira Saito

    Recently, data-driven approaches to predict the dynamical properties of nonlinear dynamical systems have become popular in the field of structural dynamics. Dynamic mode decomposition with control (DMDc) is an application of dynamic mode decomposition (DMD) to dynamical systems with control terms, which can now be applied to systems that receive external input. In this paper, we propose short-time dynamic mode decomposition (STDMD), which represents the spatio-temporal characteristics of a system by means of operators constructed for each short-time domain with a time window for swept external input and their state snapshot pairs. Based on the physical properties obtained, the time response and the frequency response of the system during steady-state vibration are clarified when the system is time evolved by external input data under conditions different from those used to construct the DMDc and STDMD models. As a numerical analysis, a forced vibration system by mass-spring-damper system that can be expressed by the Duffing equation is used. First, as in general studies, time evolution of the system was attempted using the same external force data as the external input used for model construction. Next, snapshots of the system under harmonic excitation were used for DMD model construction, and the time history and frequency responses were investigated using external input data under harmonic excitation at different frequencies for time evolution. Finally, data from the system undergoing swept sine excitation were used for model construction, and harmonic excitation data at each frequency within the sweep range were used for time evolution. Prediction of the time and frequency responses by ordinary DMDc was a linear approach that was able to represent nonlinear characteristics, but prediction became difficult when the nonlinearity was strong. On the other hand, the frequency response obtained by STDMD has been shown to be able to represent nonlinear characteristics such as jump phenomenon and hysteresis, even for systems with strong nonlinearities.


  • Effects of Rotated Stacking, Bolts, and Bonded Regions on Modal Parameters of Bonded Stator Cores of Electric Machines

    by Akira Saito, Hayato Maeba, Masami Matsubara, Kohei Furuya

    This paper discusses the vibration characteristics of the electric machine stators used for the traction of electric vehicles. Of particular interest is the effects of rotated stacking, bolts, and bonded regions on the modal characteristics of the bonded laminated stator cores. Test specimens for vibration testing have been fabricated, and experimental modal analyses have been conducted. Modal parameters, i.e., natural frequencies, mode shapes, and modal damping ratios have been extracted by a curve fit methodology. It is revealed that natural frequencies of modes involving shear deformations along axial direction are affected by rotated stacking, and bolts. Furthermore, the effect of partial bonding on the teeth region on the natural frequencies is small for low frequency modes but relatively large for high frequency modes. Moreover, it was found that bonding on the teeth region tends to increase the modal damping ratios.


  • Sound synthesis of drums based on modal representation of transfer functions

    by Marisa Nagata, Akira Saito

    In recent years, software-based music composition is becoming common among composers. In this study, we propose a sound synthesis method that simulates the sound radiation from drums using vibration transmission and acoustic characteristics of the structure of the drums, which enables one to virtually produce the radiated sound due to excitation forces accurately. First, the acoustic experimental modal analysis was conducted, where the radiated sound from a drum due to impulsive force was measured, and transfer functions between the excitation point and the points where the sound need be synthesized were obtained. The normal modes were then identified by a curve-fit methodology, and the obtained transfer functions were projected onto a subset of normal modes with the frequencies that lie within the frequency range of interest. It is shown that the synthesized sound spectra and those of the corresponding time histories are in excellent agreement with the measurements.


  • Re-designing strategy to enable a sub-system to function as a dynamic vibration absorber

    by Masami Matsubara, Kohei Takahashi, Kohei Furuya, Akira Saito, Shozo Kawamura

    In the design of a typical dynamic absorber, the components corresponding to the dynamic vibration absorber (DVA) should be reduced to a lumped constant system model comprising a mass, spring, and damper. The equivalent mass and stiffness must be determined and linked to design coefficients. However, no studies on the dynamic design of a main structure (main system) and an attached DVA (sub-system) based on an FE model without constructing a reduced-order equivalent model with a few DOFs have been conducted. This study proposes a new method of extracting and simplifying the design of a sub-system to function as a DVA using the state of a finite element (FE) model. We established the relationship between the condition of the sub-system functioning as a DVA and the modal parameter of the entire system. According to a survey, the modal kinetic energies, which were calculated from the partial mass matrix and mode vectors, of the main system and sub-system are approximately equal. We used this relationship to redesign the sub-system. As the modal kinetic energy was used as a design index, the FE model could be redesigned without constructing an equivalent lumped parameter model consisting of two or three degrees of freedom (DOFs) as in the conventional DVA design. We demonstrated the relationship between the modal kinetic energies of the main system and sub-system when it functions as a DVA for a 2-DOF lumped mass model and discussed how to distinguish the sub-system from the entire system (multi-DOF system). Considerable improvement was found in re-designing at FE model, validating the proposed method. The proposed method can be used to redesign components that behave similarly to dynamic absorbers to effectively reduce vibration from the results of FE analysis, without modeling the system as a lumped constant system.

  • Data-Driven Initial Gap Identification of Piecewise-Linear Systems Using Sparse Regression and Universal Approximation Theorem

    by Ryosuke Kanki, Akira Saito

    This paper proposes a method for identifying an initial gap in piecewise-linear (PWL) systems from data. Piecewise-linear systems appear in many engineered systems such as degraded mechanical systems and infrastructures and are known to show strong nonlinearities. To analyze the behavior of such piecewise-linear systems, it is necessary to identify the initial gap, at which the system behavior switches. The proposed method identifies the initial gap by discovering the governing equations using sparse regression and calculating the gap based on the universal approximation theorem. A key step to achieve this is to approximate a piecewise-linear function by a finite sum of piecewise-linear functions in sparse regression. The equivalent gap is then calculated from the coefficients of the multiple piecewise-linear functions and their respective switching points in the obtained equation. The proposed method is first applied to a numerical model to confirm its applicability to piecewise-linear systems. Experimental validation of the proposed method has then been conducted with a simple mass-spring-hopping system, where the method successfully identifies the initial gap in the system with high accuracy.


  • 区分線形性を有する機械システムのスパース回帰を用いた支配方程式自動生成

    by Ryosuke Kanki, Akira Saito

    In recent years, sophistication of mechanical systems complicates derivation of their governing equations. On the other hand, with the recent development of data-driven modeling methods, discovery of the governing equation of relatively simple dynamical system is becoming feasible from measurement data. However, when mechanical systems involve piecewise-linear nonlinearity such as junction points or cracks, it is difficult to identify their governing equations using these methods. Furthermore, piecewise-linear systems have an issue that it is difficult to identify the switching point in the phase space where the system changes its state. To overcome this issue, this study proposes a method to identify not only the governing equations but also the switching points for piecewise-linear systems. It is shown that the proposed method can be successfully applied to generate the governing equation of a single degree of freedom oscillator that involves repetitive contacts with a spring. This dynamic model is a piecewise-linear system and has two states: the system with a spring and without the spring. In addition, an experimental apparatus was built and the proposed method was applied to the measured data. By optimizing the threshold value and order of candidate functions, it was able to derive governing equations that reproduce the dynamics of the experimental equipment.

  • 接触力と摩擦力が作用する積層構造物の振動特性予測

    by Haruto Kojima, Takuya Katsuragawa, Kohei Furuya, Akira Saito, Masami Matsubara

    As electric vehicles become increasingly popular, motor noise can become a problem. In particular, the vibration characteristics of motor stators contribute significantly to noise, so there is a growing need to understand the vibration characteristics of stators and to develop models to predict them. Generally, a stator is a laminated structure consisting of several hundred electromagnetic steel plates stacked and joined by various methods such as caulking, welding, bonding, and bolting. Since contact and friction forces are generated between the steel plates in this laminated structure, the nonlinear nature of the structure makes it difficult to determine the vibration characteristics and prediction accuracy is low. Although it is theoretically possible to determine the effects of contact and friction using nonlinear finite element analysis, there are problems such as the calculation not converging when the number of layers increases and the calculation results being dependent on the calculation parameters. Therefore, in this study, the method proposed in a previous study to model the effects of contact and friction when two steel plates are bolted together using spring elements is applied to a laminated structure consisting of several hundred electromagnetic steel plates to verify its prediction accuracy.