TRTheodore. J. Ronningen

Theodore. J. Ronningen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Theodore. J. Ronningen has a total of 138 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Structural and electrical characterization of short-wave infrared GeSn diodes [Invited]

    by Punam Murkute, Nathan McKee, Dylan Plouffe, Eikhyun Cho, Neha Nooman, T. J. Ronningen, Sadikul Alam, Jinwoo Hwang, Teressa S. Basko, Mike Garter, et al.

    Group-IV (Si)GeSn alloys are rapidly emerging as promising candidates for monolithically integrated infrared (IR) photonic devices, offering tunable direct band gaps and full compatibility with CMOS technology. Ge 0.91 Sn 0.09 enables strong absorption in the short-wave infrared (SWIR) region near 2 µm, making it highly attractive for integrated photodetection. However, the metastable nature of Sn incorporation introduces challenges in controlling background doping and unintentional carrier polarity, both of which strongly influence dark current levels and device efficiency. In this work, we report a comprehensive study of the structural and electrical properties of Ge 0.91 Sn 0.09 PIN photodetectors grown on Ge-buffered Si (100) substrates. Structural characterization using high-resolution X-ray diffraction (HRXRD), reciprocal space mapping (RSM), and scanning transmission electron microscopy (STEM) confirms the formation of partially relaxed, high-crystallinity Ge 0.91 Sn 0.09 layers with dislocation-free interfaces. RSM analysis confirms a Sn composition of ∼9.5%, corresponding to a cutoff wavelength of ∼2 µm. Double mesa structures were fabricated on the Ge 0.91 Sn 0.09 PIN photodetectors with a fixed top mesa diameter (100 µm) and varying bottom mesa diameters (125-400 µm), and with a fixed bottom mesa diameter (500 µm) and varying bottom mesa diameters (150-400 µm) to identify the doping polarity of the material. Temperature-dependent capacitance-voltage (CVT) measurements (30–300 K) reveal n-type polarity of the doping, with a background doping of ∼4 × 10 15 cm -3 and a depletion width of 324 nm at 300 K under a bias of -0.6 V. These photodetectors demonstrated a strong photocurrent response at room temperature under 2 µm laser illumination. Arrhenius analysis of temperature-dependent current-voltage characteristics (IVT) for 200 µm and 150 µm devices identifies the dominant transport mechanisms, with a transition to trap-assisted tunneling (TAT) at low reverse bias (-0.2 V) and higher bias (-1 V). We measured responsivity and noise equivalent power (NEP) of a 200 µm diameter detector under 1.55 µm laser illumination, with a peak responsivity of 0.186 A /W, and NEP reached a minimum of 1.24× 10 -9 W/√ H z at 15 µW at 0 V. These insights into the interplay between background doping and type, transport mechanism, and NEP offer valuable guidance for optimizing low-noise, high-responsivity GeSn-based IR photodetectors, with significant potential for scalable, CMOS-compatible infrared imaging and sensing technologies.


  • Impact ionization coefficients and excess noise characteristics of Al0.85Ga0.15As0.07Sb0.93 on GaSb substrate

    by N. Gajowski, M. Muduli, T. J. Ronningen, S. Krishna

    We report the multiplication properties of Al0.85Ga0.15As0.07Sb0.93 for use in separate absorption charge and multiplication avalanche photodiode lattice matched to a GaSb substrate. The demonstration of a high gain, low excess noise multiplier lattice matched to GaSb is a critical step toward high performance avalanche photodiodes operating at wavelengths exceeding 2 μm. We have measured impact ionization coefficients of random alloy Al0.85Ga0.15As0.07Sb0.93 grown on GaSb substrates from 210 to 421 kV/cm. Our results show an α value (0.25–40×103 cm−1) significantly greater than β (0.002–4.8×103 cm−1) over the measured field range, indicating this material is a favorable multiplier candidate for electron avalanche photodiodes. We also report excess noise measurements of both p-i-n and n-i-p devices under illumination, resulting in single carrier injection. The p-i-n devices showed a low excess noise of 2.98 at a maximum gain of ∼17, while the n-i-p devices showed a high excess noise of 9.34 at a gain of ∼8, further implicating that this material predominantly multiplies electrons.


  • Open Access

    Low excess noise and high quantum efficiency avalanche photodiodes for beyond 2 µm wavelength detection

    by Hyemin Jung, Seunghyun Lee, Xiao Jin, Yifan Liu, Theodore. J. Ronningen, Christopher. H. Grein, John. P. R. David, Sanjay Krishna


  • Open Access

    A comparative study of impact ionization and avalanche multiplication in InAs, HgCdTe, and InAlAs/InAsSb superlattice

    by S. Tempel, M. Winslow, S. H. Kodati, S. Lee, T. J. Ronningen, S. Krishna, S. Krishnamurthy, C. H. Grein

    We use an ensemble Monte Carlo transport approach to calculate and compare the impact ionization and avalanche photodiode excess noise characteristics in three materials—a band-engineered InAlAs/InAsSb type-II superlattice, bulk InAs, and HgCdTe—all with an identical bandgap of 370 meV at 250 K. The electronic band structures and energy–momentum conservation conditions are used to calculate the impact ionization rates, carrier histories, multiplication gains, and excess noise characteristics. The calculated impact ionization coefficients and excess noise factors indicate a single carrier species multiplication in all three materials under low applied electric fields. We find the ratio of impact ionization coefficients to be k=7×10−4 for InAs and 3×10−4 for HgCdTe under an applied field of 50 kV/cm, and the superlattice to be k<10−6 at fields up to 400 kV/cm. The bulk materials experience avalanche breakdown as the applied field increases, transitioning to Geiger mode behavior at gains above 103 for InAs and 104 for HgCdTe. However, this breakdown is absent from the superlattice at the highest fields considered in this study due to hole confinement, indicating superior performance compared to the bulk materials. Our results demonstrate the role of superlattice band engineering in designing quality avalanche photodiode materials.


  • Open Access

    InGaAs/AlInAsSb avalanche photodiodes with low noise and strong temperature stability

    by Bingtian Guo, Mariah Schwartz, Sri H. Kodati, Kyle M. McNicholas, Hyemin Jung, Seunghyun Lee, Jason Konowitch, Dekang Chen, Junwu Bai, Xiangwen Guo, et al.

    High-sensitivity avalanche photodiodes (APDs) are used to amplify weak optical signals in a wide range of applications, including telecommunications, data centers, spectroscopy, imaging, light detection and ranging, medical diagnostics, and quantum applications. This paper reports antimony-based separate absorption, charge, and multiplication structure APDs on InP substrates. Al0.7In0.3As0.79Sb0.21 is used for the multiplier region, and InGaAs is used as the absorber. The excess noise is comparable to that of silicon APDs; the k-value is more than one order of magnitude lower than that of APDs that use InP or InAlAs for the gain region. The external quantum efficiency without an anti-reflection coating at 1550 nm is 57%. The gradient of the temperature coefficient of avalanche breakdown voltage is 6.7 mV/K/μm, which is less than one-sixth that of InP APDs, presenting the potential to reduce the cost and complexity of receiver circuits. Semi-insulating InP substrates make high-speed operation practical for widely reported AlxIn1−xAsySb1−y-based APDs.


  • Ionization coefficients and excess noise characteristics of AlInAsSb on an InP substrate

    by T. J. Ronningen, S. H. Kodati, X. Jin, S. Lee, H. Jung, X. Tao, H. I. J. Lewis, M. Schwartz, N. Gajowski, P. Martyniuk, et al.

    For short-wavelength infrared (SWIR) avalanche photodiodes, a separate absorption, charge, and multiplication design is widely used. AlInAsSb on an InP substrate is a potential multiplication layer with a lattice match to absorber candidates across the SWIR. Our new measurements demonstrate that AlInAsSb on InP is a promising multiplier candidate with a relatively low dark current density of 10−4 A/cm2 at a gain of 30; a high gain, measured up to 245 in this study; and a large differentiation of electron and hole ionization leading to a low excess noise, measured to be 2.5 at a gain of 30. These characteristics are all improvements over commercially available SWIR detectors incorporating InAlAs or InP as the multiplier. We measured and analyzed gain for multiple wavelengths to extract the ionization coefficients as a function of an electric field over the range 0.33–0.6 MV/cm.


  • Open Access

    Suppressing leakage current by interfacial engineering for highly sensitive, broadband, self-powered FACsPbI3 perovskite photodetectors

    by Bhupesh Bhardwaj, Urvashi Bothra, Shivam Singh, Sophie Mills, T. J. Ronningen, Sanjay Krishna, Dinesh Kabra

    Dark current is considered as one of the important parameters to suppress temporal noise and enhance sensitivity of photodetectors. This study shows the effect of active layer thickness and different interfacial layers in the suppression of leakage current. High-sensitivity (D* > 1012 Jones) perovskite photodetectors (PPDs) are fabricated using the device structure of ITO/PEDOT: PSS/FA0.95Cs0.05PbI3 (dPVSK)/ electron transport layer (ETL)/BCP/Ag with noise current <1 pA Hz−½. These PPDs have a broadband response from near-ultraviolet to near-infrared region (300–840 nm). The overall performance of the PPDs enhanced for the optimal thickness of active layer of dPVSK = 600 nm and ETL PC60BM layer thickness of dETL = 50 nm. The total noise current of the PPD is further suppressed by replacing the ETL PC60BM (in = 63.11 fA Hz−½) layer by a PC70BM (in = 33.41 fA Hz−½) layer. This further improved other figures of merit for these PPDs. Comparison with published reports on PPDs is included to compare with the state-of-the-art detectors.


  • Open Access

    Assessment of surface recombination in mid-wave infrared InAsSb nBn detectors using transient microwave reflectance

    by A. M. Arquitola, H. Jung, S. Lee, T. J. Ronningen, S. Krishna

    Investigation of surface recombination is an important area for infrared detectors as the demand for smaller pixels increases. In this study, we use transient microwave reflectance to characterize the minority carrier lifetime of InAsSb nBn structures under three conditions: As-Grown, blanket Barrier-Etched, and SU-8 Passivated blanket barrier-etched. A qualitative comparison of these three samples shows that the minority carrier lifetime decreases for the Barrier-Etched sample compared to the As-Grown sample, indicating that the minority carrier lifetime is sensitive to changes in the sample surface, specifically the introduction of surface states. We compare these samples quantitatively using a polynomial fit (A−1 + Bn + Cn2). We find for the As-Grown sample A = 1.22 ± 0.45 µs, B = 2.5 ± 0.2 × 10−12 cm3/s, and C = 5.004 ± 4.996 × 10−31 cm6/s, for the Barrier-Etched sample A = 1.17 ± 0.40 µs, B = 9.9 ± 0.2 × 10−12 cm3/s, and C = 9.502 ± 9.498 × 10−30 cm6/s, and for the Passivated sample A = 1.34 ± 0.45 µs, B = 5.3 ± 0.5 × 10−12 cm3/s, and C = 5.500 ± 4.500 × 10−33 cm6/s.


  • Top Cited Papers

    High gain, low noise 1550 nm GaAsSb/AlGaAsSb avalanche photodiodes

    by Seunghyun Lee, Xiao Jin, Hyemin Jung, Harry Lewis, Yifan Liu, Bingtian Guo, Sri Harsha Kodati, Mariah Schwartz, Christoph Grein, Theodore Ronningen, et al.

    High sensitivity avalanche photodiodes (APDs) operating at eye-safe infrared wavelengths (1400–1650 nm) are essential components in many communications and sensing systems. We report the demonstration of a room temperature, ultrahigh gain ( M = 278 , λ = 1550 n m , V = 69.5 V , T = 296 K ) linear mode APD on an InP substrate using a G a A s 0.5 S b 0.5 / A l 0.85 G a 0.15 A s 0.56 S b 0.44 separate absorption, charge, and multiplication (SACM) heterostructure. This represents ∼ 10 × gain improvement ( M = 278 ) over commercial, state-of-the-art InGaAs/InP-based APDs ( M ∼ 30 ) operating at 1550 nm. The excess noise factor is extremely low ( F < 3 ) at M = 70 , which is even lower than Si APDs. This design gives a quantum efficiency of 5935.3% at maximum gain. This SACM APD also shows an extremely low temperature breakdown sensitivity ( C b d ) of ∼ 11.83 m V / K , which is ∼ 10 × lower than equivalent InGaAs/InP commercial APDs. These major improvements in APD performance are likely to lead to their wide adoption in many photon-starved applications.


  • Open Access

    Determination of the background doping polarity for unintentionally doped AlGaAsSb and AlInAsSb avalanche photodiodes on InP substrates

    by M. Schwartz, S. H. Kodati, S. Lee, H. Jung, D. Chen, C. H. Grein, T. J. Ronningen, J. C. Campbell, S. Krishna

    Background doping polarity is a critical design parameter for the performance of many optoelectronic devices, including avalanche photodiodes. We have applied a technique by using capacitance–voltage (CV) measurements on double mesa structures with a p-i-n or n-i-p homojunction to determine the background polarity type of the unintentionally doped intrinsic region. Because CV measurements scale with the size of the mesa, they support design flexibility in producing variable-sized top and bottom mesa diameters. In this work, we grew, fabricated, and tested AlGaAsSb and AlInAsSb random alloy double mesa p-i-n structures and undertook CV measurements at 295, 150, and 77 K. It was found that the capacitance varied with the top mesa diameter for both material systems, and not the bottom mesa diameter, indicating that the unintentionally doped intrinsic region is n-type in nature.