Debabrata Kumar Karmokar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Debabrata Kumar Karmokar has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Karu Priyathama Esselle
School of Electrical and Data Engineering, University of Technology Sydney, Ultimo, NSW, Australia
21 shared publications - Shu-Lin Chen
Global Big Data Technologies Centre (GBDTC), University of Technology Sydney (UTS), Ultimo, NSW, Australia
9 shared publications - Yingjie Jay Guo
University of Technology Sydney
9 shared publications - Dushmantha N. Thalakotuna
School of Electrical and Data Engineering, University of Technology Sydney, Ultimo, NSW, Australia
8 shared publications - Michael Heimlich
School of Engineering, Faculty of Science and Engineering, Macquarie University, Balaclava Road, North Ryde, NSW, 2109, Australia
8 shared publications - Pei-Yuan Qin
University of Technology Sydney
8 shared publications
Latest Publications
- 9 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75  (00189456) , 1-32
Chipless RFID Multisensory Tags—Trends, Strengths, Challenges, and Prospects: A Review
The concept of Chipless Radio Frequency IDentification (CRFID) multi-parameter tag-sensors is fairly new and nowadays has gained importance among the researchers for their ability to identify objects and sense multiple parameters at once without requiring integrated circuits (ICs), on-board power sources and active components. This paper presents a comprehensive review of such tag-sensors, emphasizing its current stage of development, performance comparisons, and existing research gaps. This study provides a detailed classification of resonator structures, identification (ID) & sensing mechanisms, sensing functions & factors, and smart/sensitive materials (SMs), establishing a new unified taxonomy. Further, it provides details on the sensing mechanism and physics behind it, maps resonator types to their design principles with their sensing functions, alongside their corresponding SMs and reveals their multi-parameter decoupling and selectivity techniques. It also comments on the substrates used & the adopted printing process. A critical quantitative evaluation follows based on key ID (coding capacity, spectral and spatial density) and sensing metrics (sensitivity, dynamic range, and read range). Finally, the paper discusses current challenges such as limited coding capacity, short read range, absence of dedicated readers and standards, and issues with selectivity and suggests future directions including AI integration and scalable deployment for IoT, smart logistics, environmental monitoring, and industrial automation.
- 9 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75  (00189456) , 1-32
Chipless RFID Multisensory Tags—Trends, Strengths, Challenges, and Prospects: A Review
The concept of Chipless Radio Frequency IDentification (CRFID) multi-parameter tag-sensors is fairly new and nowadays has gained importance among the researchers for their ability to identify objects and sense multiple parameters at once without requiring integrated circuits (ICs), on-board power sources and active components. This paper presents a comprehensive review of such tag-sensors, emphasizing its current stage of development, performance comparisons, and existing research gaps. This study provides a detailed classification of resonator structures, identification (ID) & sensing mechanisms, sensing functions & factors, and smart/sensitive materials (SMs), establishing a new unified taxonomy. Further, it provides details on the sensing mechanism and physics behind it, maps resonator types to their design principles with their sensing functions, alongside their corresponding SMs and reveals their multi-parameter decoupling and selectivity techniques. It also comments on the substrates used & the adopted printing process. A critical quantitative evaluation follows based on key ID (coding capacity, spectral and spatial density) and sensing metrics (sensitivity, dynamic range, and read range). Finally, the paper discusses current challenges such as limited coding capacity, short read range, absence of dedicated readers and standards, and issues with selectivity and suggests future directions including AI integration and scalable deployment for IoT, smart logistics, environmental monitoring, and industrial automation.
- 1 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1406-1409
Millimeter-Wave Wide Angle Beam Scanning Composite Right/Left-Handed Leaky- Wave Antenna
Although leaky-wave antennas (LWAs) have excel-lent radiation properties, many suffer radiation in the broadside direction. This limitation restricts the beam scanning of LWAs, particularly uniform LWAs, in the forward direction only. A composite right/left-handed (CRLH) LWA for millimeter wave application is discussed in this paper. The unit cell of the antenna consists of two patches with a gap between them, one with a slot in the middle and another shorted to the ground using four vias. The simulation results confirm that the radiating beam of the antenna scans continuously from -63° to +70° as frequency sweeps from 31.5 to 60 GHz.
- 1 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1406-1409
Millimeter-Wave Wide Angle Beam Scanning Composite Right/Left-Handed Leaky- Wave Antenna
Although leaky-wave antennas (LWAs) have excel-lent radiation properties, many suffer radiation in the broadside direction. This limitation restricts the beam scanning of LWAs, particularly uniform LWAs, in the forward direction only. A composite right/left-handed (CRLH) LWA for millimeter wave application is discussed in this paper. The unit cell of the antenna consists of two patches with a gap between them, one with a slot in the middle and another shorted to the ground using four vias. The simulation results confirm that the radiating beam of the antenna scans continuously from -63° to +70° as frequency sweeps from 31.5 to 60 GHz.
- 5 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71  (11) , 8429-8440
Wideband Fixed-Beam Single-Piece Leaky Wave Antenna With Controlled Dispersion Slope
Leaky wave antennas (LWAs) have been widely investigated for wireless systems because of their simple feed, low profile, and easy integration. They typically have a dispersive traveling wave leading to beam squinting behavior, which can significantly decrease the useful operating bandwidth in point-to-point communications. An innovative method that avoids beam squint with frequency over a wide band is developed in this work using a negative dispersion slope. By integrating a baffle of square bracket-shaped metal pieces into a transverse-slot LWA, the main beam angle is almost fixed at an angle, $\theta = 37^{\circ } \pm 2^{\circ }$ , across a wide frequency band from 9.5 to 12.2 GHz. The wide bandwidth is a consequence of the negative dispersion slope produced by the interaction between the baffle and the slotted waveguide. In the $\theta = 37^{\circ }$ direction, the gain variation is less than 3 dB across this band. Equivalent circuit analysis and full-wave modeling are presented to demonstrate the negative-slope dispersion diagram. The obtained 3-dB gain curve exhibits a filter characteristic. In addition, the bandwidth can be chosen by a suitable selection of parameters. It is the first time that these desirable features have been reported for wideband fixed-beam LWAs. The final antenna was fabricated with a low-cost additive manufacturing (3-D printing) technology. The measured results agree well with the simulated ones and verify the effectiveness of the antennas developed in this way.
- 5 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71  (11) , 8429-8440
Wideband Fixed-Beam Single-Piece Leaky Wave Antenna With Controlled Dispersion Slope
Leaky wave antennas (LWAs) have been widely investigated for wireless systems because of their simple feed, low profile, and easy integration. They typically have a dispersive traveling wave leading to beam squinting behavior, which can significantly decrease the useful operating bandwidth in point-to-point communications. An innovative method that avoids beam squint with frequency over a wide band is developed in this work using a negative dispersion slope. By integrating a baffle of square bracket-shaped metal pieces into a transverse-slot LWA, the main beam angle is almost fixed at an angle, $\theta = 37^{\circ } \pm 2^{\circ }$ , across a wide frequency band from 9.5 to 12.2 GHz. The wide bandwidth is a consequence of the negative dispersion slope produced by the interaction between the baffle and the slotted waveguide. In the $\theta = 37^{\circ }$ direction, the gain variation is less than 3 dB across this band. Equivalent circuit analysis and full-wave modeling are presented to demonstrate the negative-slope dispersion diagram. The obtained 3-dB gain curve exhibits a filter characteristic. In addition, the bandwidth can be chosen by a suitable selection of parameters. It is the first time that these desirable features have been reported for wideband fixed-beam LWAs. The final antenna was fabricated with a low-cost additive manufacturing (3-D printing) technology. The measured results agree well with the simulated ones and verify the effectiveness of the antennas developed in this way.
- Open Access
Beam-Switching Antennas for 5G Millimeter-Wave Wireless Terminals
Beam-switching is one of the paramount focuses of 28 GHz millimeter-wave 5G devices. In this paper, a one-dimensional (1D) pattern reconfigurable leaky-wave antenna (LWA) was investigated and developed for wireless terminals. In order to provide a cost-effective solution, a uniform half-width LWA was used. The 1D beam-switching LWA was designed using three feed points at three different positions; by selecting the feeds, the direction of the beam can be switched. The antenna can switch the beam in three different directions along the antenna axis, such as backward, broadside, and forward. The 1D beam-switching antenna was fabricated, and because of the wide beamwidth, the measured radiation patterns can fill 128 of space (3 dB coverage), from = −64 to +64 at = 0. Following this, two of these antennas were placed at right angles to each other to achieve two-directional (2D) beam switching. The 2D beam-switching antenna pair was also prototyped and tested after integrating them into the ground plane of a wireless device. The antenna is able to point the beam in five different directions; moreover, its beam covers 167 ( = −89 to +78) at = 0, and 154 ( = −72 to +82) at = 90.Open AccessBeam-Switching Antennas for 5G Millimeter-Wave Wireless Terminals
Beam-switching is one of the paramount focuses of 28 GHz millimeter-wave 5G devices. In this paper, a one-dimensional (1D) pattern reconfigurable leaky-wave antenna (LWA) was investigated and developed for wireless terminals. In order to provide a cost-effective solution, a uniform half-width LWA was used. The 1D beam-switching LWA was designed using three feed points at three different positions; by selecting the feeds, the direction of the beam can be switched. The antenna can switch the beam in three different directions along the antenna axis, such as backward, broadside, and forward. The 1D beam-switching antenna was fabricated, and because of the wide beamwidth, the measured radiation patterns can fill 128 of space (3 dB coverage), from = −64 to +64 at = 0. Following this, two of these antennas were placed at right angles to each other to achieve two-directional (2D) beam switching. The 2D beam-switching antenna pair was also prototyped and tested after integrating them into the ground plane of a wireless device. The antenna is able to point the beam in five different directions; moreover, its beam covers 167 ( = −89 to +78) at = 0, and 154 ( = −72 to +82) at = 90. - Open Access
Antennas for Licensed Shared Access in 5G Communications with LTE Mid- and High-Band Coverage
Two novel antennas are presented for mobile devices to enable them to access both licensed shared access (LSA) bands (1452–1492 and 2300–2400 MHz) and all the long-term evolution (LTE) mid (1427–2690 MHz) and high (3400–3800 MHz) bands, together with the GSM1800, GSM1900, UMTS, and 3.3 GHz WiMAX bands. These antennas do not require any passive or active lumped elements for input impedance matching. One of them is a dual-band antenna and the other is a wideband antenna. Both antennas have high efficiency in all the LSA bands, as well as the mid- and high-LTE bands, and nearly omnidirectional radiation patterns in the mid band. In the high band, the radiation patterns of the wideband antenna are less directional than those of the dual-band antenna. The wideband antenna was fabricated and tested and the measurements demonstrated that it had good wideband performance in a wide frequency range from 1.37 to 4 GHz, covering all the above-mentioned bands.
Open AccessAntennas for Licensed Shared Access in 5G Communications with LTE Mid- and High-Band Coverage
Two novel antennas are presented for mobile devices to enable them to access both licensed shared access (LSA) bands (1452–1492 and 2300–2400 MHz) and all the long-term evolution (LTE) mid (1427–2690 MHz) and high (3400–3800 MHz) bands, together with the GSM1800, GSM1900, UMTS, and 3.3 GHz WiMAX bands. These antennas do not require any passive or active lumped elements for input impedance matching. One of them is a dual-band antenna and the other is a wideband antenna. Both antennas have high efficiency in all the LSA bands, as well as the mid- and high-LTE bands, and nearly omnidirectional radiation patterns in the mid band. In the high band, the radiation patterns of the wideband antenna are less directional than those of the dual-band antenna. The wideband antenna was fabricated and tested and the measurements demonstrated that it had good wideband performance in a wide frequency range from 1.37 to 4 GHz, covering all the above-mentioned bands.
- Open Access
- 13 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 142084-142094
A Compact Reconfigurable 1-D Periodic Structure in GaAs MMIC With Stopband Switching, Dual-Band Operation and Tuning Capabilities
This paper presents a systematic study of a compact and reconfigurable periodic structure in GaAs MMIC technology. Compactness is achieved by the introduction of spiral inductors in a conventional unit cell without disturbing the reactive loading mechanism. The proposed architecture exhibits a 28.3% wider stopband with 62.6% smaller footprint compared to a conventional structure. The compactness and bandwidth improvement in the proposed structure is explained with the help of dispersion and circuit analysis. The reconfigurability built into the design using PIN diodes allows stopband switching, dual-band operation and tuning capabilities with the mere use of a single reactive load in its unit cell. To the best of the authors knowledge, it is the first time a reconfigurable MMIC implementation is realized using the proposed structure or even the conventional design. As a guide to design, sensitivity analysis to filter performance is presented for important structure parameters. Switching element parasitics are discussed in two ways: firstly, with the design and measurement of structures with idealized switching conditions and in second, with the circuit and full-wave EM modelling of the finite periodic structure with the actual PIN diodes. The on-chip measurements of the fully reconfigurable filter show excellent agreement with simulations.
- 13 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 142084-142094
Open AccessA Compact Reconfigurable 1-D Periodic Structure in GaAs MMIC With Stopband Switching, Dual-Band Operation and Tuning Capabilities
This paper presents a systematic study of a compact and reconfigurable periodic structure in GaAs MMIC technology. Compactness is achieved by the introduction of spiral inductors in a conventional unit cell without disturbing the reactive loading mechanism. The proposed architecture exhibits a 28.3% wider stopband with 62.6% smaller footprint compared to a conventional structure. The compactness and bandwidth improvement in the proposed structure is explained with the help of dispersion and circuit analysis. The reconfigurability built into the design using PIN diodes allows stopband switching, dual-band operation and tuning capabilities with the mere use of a single reactive load in its unit cell. To the best of the authors knowledge, it is the first time a reconfigurable MMIC implementation is realized using the proposed structure or even the conventional design. As a guide to design, sensitivity analysis to filter performance is presented for important structure parameters. Switching element parasitics are discussed in two ways: firstly, with the design and measurement of structures with idealized switching conditions and in second, with the circuit and full-wave EM modelling of the finite periodic structure with the actual PIN diodes. The on-chip measurements of the fully reconfigurable filter show excellent agreement with simulations.
- 1 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 22  (11) , 38-51
Periodic Structures for Reconfigurable Filter Design: A Comprehensive Review
With the advent of 5G, software-defined radios (SDRs), and ultra-wideband systems, there is a rapid rise in the demand for reconfigurable RF front ends. Conventional methods of using filter banks or cascading multiple devices to achieve wideband performance would result in bulky hardware. Devices that can change their characteristics and respond in a controlled manner to a desired input are suitable for such designs. In filtering applications, the most desirable adaptive features include band-switching capabilities, the use of a cutoff frequency and/or bandwidth tuning, and a change in filter response from passband to stopband. Periodic structures have demonstrated great potential in achieving these characteristics.
- 1 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave Magazine
- Vol. 22  (11) , 38-51
Periodic Structures for Reconfigurable Filter Design: A Comprehensive Review
With the advent of 5G, software-defined radios (SDRs), and ultra-wideband systems, there is a rapid rise in the demand for reconfigurable RF front ends. Conventional methods of using filter banks or cascading multiple devices to achieve wideband performance would result in bulky hardware. Devices that can change their characteristics and respond in a controlled manner to a desired input are suitable for such designs. In filtering applications, the most desirable adaptive features include band-switching capabilities, the use of a cutoff frequency and/or bandwidth tuning, and a change in filter response from passband to stopband. Periodic structures have demonstrated great potential in achieving these characteristics.
- 14 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69  (5) , 2987-2992
Backward-to-Forward Wide-Angle Fast Beam-Scanning Leaky-Wave Antenna With Consistent Gain
A planar periodic leaky-wave antenna (PLWA) with continuous backward-to-forward beam-scanning capability and consistent gain is presented. The PLWA is made of a new type of periodically arranging meander line structures, in which the capacitive coupling between neighboring units plays the key role in achieving a high scanning rate. In detail, the beam-scanning rate of the proposed PLWA is efficiently tuned by varying the gap between two adjacent units, without considerably changing the working frequency band. To mitigate the open stopband (OSB) and to improve the impedance matching, several inductive open stubs are introduced into a single meander line unit cell to enhance the radiation. In the experiment, a prototype of the proposed PLWA was fabricated and measured. The simulated and measured beams show good agreement in terms of scanning range and radiation performance. A continuous beam scanning from -60° to +58° through broadside in the frequency band of 5.95-7.1 GHz is observed, and hence, a 102.6°/GHz scanning rate is realized in practice. Besides, the PLWA shows an average gain level of 11.96 dBi with a variation lower than 2 dB and a sidelobe below -10 dB at all the measured frequencies. The proposed PLWA may have potential applications in radar, microwave imaging, and wireless communication due to its compact structure, easy to fabricate, and dispersionless performance.
- 14 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69  (5) , 2987-2992
Backward-to-Forward Wide-Angle Fast Beam-Scanning Leaky-Wave Antenna With Consistent Gain
A planar periodic leaky-wave antenna (PLWA) with continuous backward-to-forward beam-scanning capability and consistent gain is presented. The PLWA is made of a new type of periodically arranging meander line structures, in which the capacitive coupling between neighboring units plays the key role in achieving a high scanning rate. In detail, the beam-scanning rate of the proposed PLWA is efficiently tuned by varying the gap between two adjacent units, without considerably changing the working frequency band. To mitigate the open stopband (OSB) and to improve the impedance matching, several inductive open stubs are introduced into a single meander line unit cell to enhance the radiation. In the experiment, a prototype of the proposed PLWA was fabricated and measured. The simulated and measured beams show good agreement in terms of scanning range and radiation performance. A continuous beam scanning from -60° to +58° through broadside in the frequency band of 5.95-7.1 GHz is observed, and hence, a 102.6°/GHz scanning rate is realized in practice. Besides, the PLWA shows an average gain level of 11.96 dBi with a variation lower than 2 dB and a sidelobe below -10 dB at all the measured frequencies. The proposed PLWA may have potential applications in radar, microwave imaging, and wireless communication due to its compact structure, easy to fabricate, and dispersionless performance.
- Open Access
- 24 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 155492-155505
Bandstop Filter Synthesis Scheme for Reactively Loaded Microstrip Line Based 1-D Periodic Structures
A 1-D finite electromagnetic bandgap (EBG) periodic structure is studied. In the structure, EBG behaviour arises from a unit cell comprised of a metallic patch sandwiched between microstrip line and ground plane. Reactive loading offered by patch size determines the bandgap position. A detailed parametric study of various physical structure parameters is presented as a basis to develop a interrelation between physical parameters of the structure and cutoff frequencies. Closed-form synthesis equations are then formulated using curve fitting techniques. Subsequently, a step-by-step design methodology is presented to get a close first pass approximation of structure dimensions for a given specification. This design method reduces the effort required for a designer to perform extensive electromagnetic simulations at early stages of the design. The proposed synthesis method is tested for a variety of commercially available substrates and different frequency ranges for validation. Comparison with electromagnetic (EM) simulations and measurement show that the proposed synthesis method provides first pass approximation of the physical structure dimensions with 94% accuracy.
- 24 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 155492-155505
Open AccessBandstop Filter Synthesis Scheme for Reactively Loaded Microstrip Line Based 1-D Periodic Structures
A 1-D finite electromagnetic bandgap (EBG) periodic structure is studied. In the structure, EBG behaviour arises from a unit cell comprised of a metallic patch sandwiched between microstrip line and ground plane. Reactive loading offered by patch size determines the bandgap position. A detailed parametric study of various physical structure parameters is presented as a basis to develop a interrelation between physical parameters of the structure and cutoff frequencies. Closed-form synthesis equations are then formulated using curve fitting techniques. Subsequently, a step-by-step design methodology is presented to get a close first pass approximation of structure dimensions for a given specification. This design method reduces the effort required for a designer to perform extensive electromagnetic simulations at early stages of the design. The proposed synthesis method is tested for a variety of commercially available substrates and different frequency ranges for validation. Comparison with electromagnetic (EM) simulations and measurement show that the proposed synthesis method provides first pass approximation of the physical structure dimensions with 94% accuracy.
- 26 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68  (7) , 5257-5268
Uniplanar High-Gain 2-D Scanning Leaky-Wave Multibeam Array Antenna at Fixed Frequency
A new topology for 2-D scanning multibeam array antenna (MAA) design is proposed. Different from the traditional 2-D scanning scheme, this new design approach is composed of a 1-D beam-forming network (BFN) and a set of 1-D pattern-reconfigurable antennas, which can together realize 2-D multibeam scanning. Compare with traditional schemes, the proposed topology has advantages of uniplanar configuration and better flexibility in scaling up the array. To demonstrate the validity of the proposed topology, a high-gain 2-D scanning leaky-wave MAA operating at 10 GHz is designed. A horn BFN and a fixed-frequency leaky-wave antenna (LWA) are designed as the feeding and radiation part, respectively. A number of new techniques are also developed for the design. For the horn BFN, a new phase-compensation method to reduce the gain drop is presented and phase inverters are introduced to provide an extra 180: of phase shift. Meanwhile, some modification of the LWA is conducted for better compatibility between the horn BFN and the LWA. A substrate integrated waveguide (SIW) to half-mode SIW (HMSIW) transition is introduced between the horn BFN and the LWA. The LWAs are terminally shorted to avoid the usage of matched loads. The width of the LWA is investigated to achieve suitable beam coverage and S-parameters. Finally, the antenna is fabricated and experiments are conducted to verify the agreement between simulation and measurement.
- 26 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 68  (7) , 5257-5268
Uniplanar High-Gain 2-D Scanning Leaky-Wave Multibeam Array Antenna at Fixed Frequency
A new topology for 2-D scanning multibeam array antenna (MAA) design is proposed. Different from the traditional 2-D scanning scheme, this new design approach is composed of a 1-D beam-forming network (BFN) and a set of 1-D pattern-reconfigurable antennas, which can together realize 2-D multibeam scanning. Compare with traditional schemes, the proposed topology has advantages of uniplanar configuration and better flexibility in scaling up the array. To demonstrate the validity of the proposed topology, a high-gain 2-D scanning leaky-wave MAA operating at 10 GHz is designed. A horn BFN and a fixed-frequency leaky-wave antenna (LWA) are designed as the feeding and radiation part, respectively. A number of new techniques are also developed for the design. For the horn BFN, a new phase-compensation method to reduce the gain drop is presented and phase inverters are introduced to provide an extra 180: of phase shift. Meanwhile, some modification of the LWA is conducted for better compatibility between the horn BFN and the LWA. A substrate integrated waveguide (SIW) to half-mode SIW (HMSIW) transition is introduced between the horn BFN and the LWA. The LWAs are terminally shorted to avoid the usage of matched loads. The width of the LWA is investigated to achieve suitable beam coverage and S-parameters. Finally, the antenna is fabricated and experiments are conducted to verify the agreement between simulation and measurement.