HBHarrison Logan Bartlett

Harrison Logan Bartlett

*This is an algorithmically generated author record based on publicly available information.

Harrison Logan Bartlett has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Design and Assist-As-Needed Control of a Lightly Powered Prosthetic Knee

    by Harrison Logan Bartlett, Shane T. King, Michael Goldfarb, Brian Edward Lawson

    This paper presents the design of a swing-assist prosthetic knee capable of providing stabilizing passive torques during the stance phase of walking and supplementing the passive swing phase behavior of the prosthetic knee with small active torques. The prosthesis design utilizes a novel actuator which integrates a symmetric multi-chamber hydraulic cylinder and a highly backdrivable linear electromechanical drive system into a single compact package. This actuator is implemented in a self-contained prosthesis design (including batteries and embedded system) which weighs 1.7 kg and is 28 cm in length, making this design comparable in size/mass to commercially available microprocessor-controlled prosthetic knees. The device is controlled using a finite state machine with a novel assist-as-needed controller operating during the swing phase. This assist-as-needed controller supplements a nominally passive swing phase behavior with small amounts of active power to enhance user safety. The device and controller were assessed on a single participant who took part in level ground walking experiments with both the swing-assist prosthesis and his daily-use device. Results indicate that the swing-assist prosthesis increases maximum swing phase knee flexion angle relative to the subject’s daily-use device. Furthermore, the swing-assist prosthesis was shown to automatically vary its assistance across walking speeds.


  • Open Access

    A Semi-Powered Ankle Prosthesis and Unified Controller for Level and Sloped Walking

    by Harrison L. Bartlett, Shane T. King, Michael Goldfarb, Brian E. Lawson

    This paper describes a semi-powered ankle prosthesis and corresponding unified controller that provides biomimetic behavior for level and sloped walking without requiring identification of ground slope or modulation of control parameters. The controller is based on the observation that healthy individuals maintain an invariant external quasi-stiffness (spring like behavior between the shank and ground) when walking on level and sloped terrain. Emulating an invariant external quasi-stiffness requires an ankle that can vary the set-point (i.e., equilibrium angle) of the ankle stiffness. A semi-powered ankle prosthesis that incorporates a novel constant-volume power-asymmetric actuator was developed to provide this behavior, and the unified controller was implemented on it. The device and unified controller were assessed on three subjects with transtibial amputations while walking on inclines, level ground, and declines. Experimental results suggest that the prosthesis and accompanying controller can provide a consistent external quasi-stiffness similar to healthy subjects across all tested ground slopes.


  • Design and Characterization of a Five-Chamber Constant-Volume Hydraulic Actuator

    by Beau Johnson, Harrison Bartlett, Michael Goldfarb

    This paper describes a new design for a constant-fluid-volume, also known as a symmetrical, hydraulic cylinder. In contrast to the two fluid volume chambers of a typical hydraulic cylinder, the constant-fluid-volume cylinder contains five potential fluid chambers. Relative to three and four chamber designs, both previously described in the engineering literature, the five chamber design enables a minimum-diameter solution with a simpler porting implementation. Following a general description of the five-chamber design and its motivation, a five-chamber cylinder prototype is described and presented. Experimental results are presented comparing some behavioral characteristics of the fivechamber cylinder to a double-rod cylinder, and to two variations of single-rod implementations. Finally, a minimum-diameter five-chamber cylinder variant is described, and its geometric characteristics compared to equivalent doublerod and four-chamber cylinder implementations.


  • Design of a Semipowered Stance-Control Swing-Assist Transfemoral Prosthesis

    by Jantzen T. Lee, Harrison Logan Bartlett, Michael Goldfarb

    This article describes the design of a new type of knee prosthesis called a stance-control swing-assist (SCSA) knee prosthesis. The device is motivated by the recognition that energetically passive stance-controlled microprocessor-controlled knees (SCMPKs) offer many desirable characteristics, such as quiet operation, low weight, high-impedance stance support, and an inertially driven swing-phase motion. Due to the latter, however, SCMPKs are also highly susceptible to swing-phase perturbations, which can increase the likelihood of falling. The SCSA prosthesis supplements the behavior of an SCMPK with a small motor that maintains the low output impedance of the SCMPK swing state, while adding a supplemental closed-loop controller around it. This article elaborates upon the motivation for the SCSA prosthesis, describes the design of a prosthesis prototype, and provides human-subject testing data that demonstrate potential device benefits relative to an SCMPK during both nonperturbed and perturbed walking.


  • Design, Control, and Preliminary Assessment of a Multifunctional Semipowered Ankle Prosthesis

    by Harrison L. Bartlett, Brian E. Lawson, Michael Goldfarb

    This paper describes the design, control, and preliminary assessment of a novel microprocessor-controlled multifunction ankle prosthesis that provides three microprocessor-controlled behaviors - a selectable stiffness equilibrium angle, lockable conformal damping, and swing-phase repositioning. Following a description of the motivation for providing these behaviors, the authors provide a detailed description of the device and walking controller design. This device utilizes a power-asymmetric linear actuator to provide the desired functionality in a compact and lightweight package through a combination of both hydraulic and electromechanical actuation approaches. The device is controlled for level ground walking via a finite state machine. The functionality of the prosthesis is demonstrated by: 1) a set of benchtop experiments that characterize the ability of the prosthesis to provide the three desired behaviors; and 2) an experiment in which the prosthesis was worn by a transtibial amputee during walking. Both sets of experiments indicate that the prosthesis provides the functionality for which it was designed.


  • Open Access

    On the design of power gear trains: Insight regarding number of stages and their respective ratios

    by Harrison L Bartlett, Brian E Lawson, Michael Goldfarb

    This paper presents a formulation for selecting the stage ratios and number of stages in a multistage transmission with a given desired total transmission ratio in a manner that maximizes efficiency, maximizes acceleration, or minimizes the mass of the transmission. The formulation is used to highlight several implications for gear train design, including the fact that minimizing rotational inertia and mass are competing objectives with respect to optimal selection of stage ratios, and that both rotational inertia and mass can often be minimized by increasing the total number of stages beyond a minimum realizable number. Additionally, a multistage transmission will generally provide maximum acceleration when the stage ratios increase monotonically from the motor to the load. The transmission will have minimum mass when the stage ratios decrease monotonically. The transmission will also provide maximum efficiency when the corresponding stages employ constant stage ratios. This paper aims to use this optimization formulation to elucidate tradeoffs between various common objectives in gear train design (efficiency, acceleration, and mass).


  • A Stair Ascent and Descent Controller for a Powered Ankle Prosthesis

    by Steven Culver, Harrison Bartlett, Amanda Shultz, Michael Goldfarb

    This paper presents a control system for a powered transtibial prosthesis that provides stair ascent and descent capability, as well as an ability for user-controlled transitions between walking, standing, stair ascent, and stair descent. The control system was implemented on a powered prosthesis and evaluated on a single unilateral transtibial amputee subject. The ability of the prosthesis to provide appropriate functionality during stair ascent and descent was assessed by comparing gait kinematics and kinetics of the prosthesis to those of a passive dynamic elastic response (DER) prosthesis and those of a set of non-amputee subjects. Data from the assessment indicates that the powered prosthesis is able to provide some desirable stair ascent and stair descent characteristics, relative to the passive prosthesis.


  • A Phase Variable Approach for IMU-Based Locomotion Activity Recognition

    by Harrison L. Bartlett, Michael Goldfarb

    Objective: This paper describes a gait classification method which utilizes measured motion of the thigh segment provided by an inertial measurement unit (IMU). Methods: The classification method employs a phase-variable description of gait, and identifies a given activity based on the expected curvature characteristics of that activity over a gait cycle. The classification method was tested in experiments conducted with seven healthy subjects performing three different locomotor activities: level ground walking, stair descent, and stair ascent. Classification accuracy of the phase variable classification method was assessed for classifying each activity, and transitions between activities, and compared to a linear discriminant analysis (LDA) classifier as a benchmark. Results: For the subjects tested, the phase variable classification method outperformed LDA when using non-subject-specific training data, while the LDA outperformed the phase variable approach when using subject-specific training. Conclusions: The proposed method may provide improved classification accuracy for gait classification applications trained with non-subject-specific data. Significance: This paper offers a new method of gait classification based on a phase variable description. The method is shown to provide improved classification accuracy relative to an LDA pattern recognition framework when trained with non-subject-specific data.


  • Open Access

    Optimal Transmission Ratio Selection for Electric Motor Driven Actuators With Known Output Torque and Motion Trajectories

    by Harrison L. Bartlett, Brian E. Lawson, Michael Goldfarb

    This paper presents a method for selecting the optimal transmission ratio for an electric motor for applications for which the desired torque and motion at the transmission output are known a priori. Representative applications for which the desired output torque and motion are periodic and known include robotic manipulation, robotic locomotion, powered prostheses, and exoskeletons. Optimal transmission ratios are presented in two senses: one that minimizes the root-mean-square (RMS) electrical current and one that minimizes the RMS electrical power. An example application is presented in order to demonstrate the method for optimal transmission ratio selection.