Taishi Kimura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Taishi Kimura has a total of 80 co-authors. Here are the top co-authors by number of shared publications:
- Daisuke Nakamura
Toyota Central R&D Labs., Inc. Nagakute, Aichi 480-1192, Japan
13 shared publications Keita Kataoka
Toyota Cent Res & Dev Labs Inc, Nagakute, Aichi 4801192, Japan
4 shared publicationsAkira Fujimaki
Dept. of Quantum Eng., Nagoya Univ., Nagoya, Japan
3 shared publicationsKayo Horibuchi
3 shared publicationsMasumi Inoue
Dept. of Quantum Eng., Nagoya Univ., Nagoya, Japan
3 shared publicationsMitsuhiro Watanabe
Dept. of Quantum Eng., Nagoya Univ., Nagoya, Japan
3 shared publications
Latest Publications
- Open Access
- 20 October 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65  (20) , 207501
Spatially resolved probing of near-field magnetic shielding by planar micro-metallic loops in the GHz range
Precise control of near-field magnetic fields is essential for advancing microwave devices in quantum sensing and computing applications. In this study, we present a near-field magnetic shield based on a microscale planar metallic loop array operating in the GHz range. The fundamental shielding properties are elucidated through the analysis of a single loop element. Utilizing optically detected magnetic resonance and Rabi oscillation measurements of nitrogen-vacancy centers in diamond, we directly probe the microwave magnetic field in proximity to the loop element. Our measurements demonstrate that loop structures with a width of 200 μm attenuate the local magnetic field by approximately 70% at 2.84 GHz. Furthermore, numerical simulations reveal that effective shielding is preserved for loop widths down to several micrometers. These findings provide valuable design guidelines for near-field magnetic field management and provide a scalable strategy for mitigating unwanted magnetic flux in integrated microwave devices.
- 20 October 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65  (20) , 207501
Open AccessSpatially resolved probing of near-field magnetic shielding by planar micro-metallic loops in the GHz range
Precise control of near-field magnetic fields is essential for advancing microwave devices in quantum sensing and computing applications. In this study, we present a near-field magnetic shield based on a microscale planar metallic loop array operating in the GHz range. The fundamental shielding properties are elucidated through the analysis of a single loop element. Utilizing optically detected magnetic resonance and Rabi oscillation measurements of nitrogen-vacancy centers in diamond, we directly probe the microwave magnetic field in proximity to the loop element. Our measurements demonstrate that loop structures with a width of 200 μm attenuate the local magnetic field by approximately 70% at 2.84 GHz. Furthermore, numerical simulations reveal that effective shielding is preserved for loop widths down to several micrometers. These findings provide valuable design guidelines for near-field magnetic field management and provide a scalable strategy for mitigating unwanted magnetic flux in integrated microwave devices.
- 6 May 2025
- Published by American Physical Society (APS) in Physical Review B
- Vol. 111  (17)
Surface acoustic wave direction sensing enabled by resonant mode interference in a single micropillar resonator
- 6 May 2025
- Published by American Physical Society (APS) in Physical Review B
- Vol. 111  (17)
Surface acoustic wave direction sensing enabled by resonant mode interference in a single micropillar resonator
- Open Access
- 21 April 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126  (16)
Computationally guided experimental validation of divacancy defect formation in 4H-SiC
Recent research into solid-state qubits for quantum information science has focused on optically addressable spin defects such as the negatively charged nitrogen-vacancy center in diamond and the neutrally charged divacancy (VV) in 4H-SiC as scalable quantum sensors and networking qubits. Within this context, direct investigations of the structural origin and defect formation dynamics of a sub-set of the VV center in 4H-SiC remain lacking. Here, we take a systematic experimental approach guided by predictions from first-principles simulations to gain a thorough mechanistic understanding of the VV defect formation and control in 4H-SiC. We study the effect of annealing time and temperature on VV formation in high-purity semi-insulating 4H-SiC samples following electron irradiation. Three different temperatures (1123, 1273, and 1473 K) and annealing duration (from 0.5 to 72 h) are chosen to explore VV formation in different regions. We find that samples annealed at 1273 K give the highest VV-related photoluminescence (PL) intensities, in agreement with the prediction from first-principles calculations. Furthermore, the logarithmic dependence of VV-related PL intensities on the annealing duration at 1273 K indicates that 1273 K provides sufficient thermal energy for silicon vacancy migration but not for VV migration. Together, these results suggest that efficient VV formation occurs above the VSi migration temperature and below the VV migration threshold.
- 21 April 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126  (16)
Open AccessComputationally guided experimental validation of divacancy defect formation in 4H-SiC
Recent research into solid-state qubits for quantum information science has focused on optically addressable spin defects such as the negatively charged nitrogen-vacancy center in diamond and the neutrally charged divacancy (VV) in 4H-SiC as scalable quantum sensors and networking qubits. Within this context, direct investigations of the structural origin and defect formation dynamics of a sub-set of the VV center in 4H-SiC remain lacking. Here, we take a systematic experimental approach guided by predictions from first-principles simulations to gain a thorough mechanistic understanding of the VV defect formation and control in 4H-SiC. We study the effect of annealing time and temperature on VV formation in high-purity semi-insulating 4H-SiC samples following electron irradiation. Three different temperatures (1123, 1273, and 1473 K) and annealing duration (from 0.5 to 72 h) are chosen to explore VV formation in different regions. We find that samples annealed at 1273 K give the highest VV-related photoluminescence (PL) intensities, in agreement with the prediction from first-principles calculations. Furthermore, the logarithmic dependence of VV-related PL intensities on the annealing duration at 1273 K indicates that 1273 K provides sufficient thermal energy for silicon vacancy migration but not for VV migration. Together, these results suggest that efficient VV formation occurs above the VSi migration temperature and below the VV migration threshold.
- Open Access
- 1 April 2024
- Published by AIP Publishing in APL Materials
- Vol. 12  (4)
Evolution of quantum spin sensing: From bench-scale ODMR to compact integrations
This paper provides a comprehensive review of quantum spin sensing with a focus on the nitrogen vacancy (NV) center in diamond. Beginning with the discovery of optically detected magnetic resonance in NV centers, we trace the evolution of this technology and its integration with complementary metal-oxide-semiconductor technology, marking a significant advancement in measurement science. The unique optical and spin properties of NV centers, operational at room temperature and under ambient conditions, have broadened their application spectrum, notably in magnetometry for nanoscale magnetic field detection. This work describes the transition from isolated NV centers to dense ensembles, highlighting the challenges and advancements in microfabrication and nanofabrication that have facilitated the integration of these centers with photonic structures and electronic devices. The efficient readout of NV spin states and the challenges in miniaturization are addressed, showcasing the development of compact, portable quantum sensors. We also discuss the potential impact of these sensors in various domains, including vehicle sensor systems and biomedical applications, underscoring the significance of environmental influences on magnetometric readings.
- 1 April 2024
- Published by AIP Publishing in APL Materials
- Vol. 12  (4)
Open AccessEvolution of quantum spin sensing: From bench-scale ODMR to compact integrations
This paper provides a comprehensive review of quantum spin sensing with a focus on the nitrogen vacancy (NV) center in diamond. Beginning with the discovery of optically detected magnetic resonance in NV centers, we trace the evolution of this technology and its integration with complementary metal-oxide-semiconductor technology, marking a significant advancement in measurement science. The unique optical and spin properties of NV centers, operational at room temperature and under ambient conditions, have broadened their application spectrum, notably in magnetometry for nanoscale magnetic field detection. This work describes the transition from isolated NV centers to dense ensembles, highlighting the challenges and advancements in microfabrication and nanofabrication that have facilitated the integration of these centers with photonic structures and electronic devices. The efficient readout of NV spin states and the challenges in miniaturization are addressed, showcasing the development of compact, portable quantum sensors. We also discuss the potential impact of these sensors in various domains, including vehicle sensor systems and biomedical applications, underscoring the significance of environmental influences on magnetometric readings.
- Open Access
- 29 January 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124  (5)
Impurity reduction in lightly doped n-type gallium nitride layer grown via halogen-free vapor-phase epitaxy
The development of gallium nitride (GaN) vertical-type metal-oxide-semiconductor field-effect transistors and p–i–n diode devices has gathered increasing attention. These devices require an n-type drift layer with a low doping level of 1016 cm−3 or less, minimized point defects inhibiting electron conduction, and a layer approximately 10 μm thick. Therefore, a practical method with a growth rate of at least several tens of μm/h and impurity concentrations of less than 1015 cm−3, except for that of dopants, is necessary. Halogen-free vapor-phase epitaxy (HF-VPE) has a high growth rate suitable for fabricating thick drift layers and utilizes a simple reaction between Ga vapor and ammonia gas (without a corrosive halogen gas), resulting in lower impurity levels. Herein, we eliminated the quartz content from the high-temperature zone to reduce the excess unintentional Si doping and identified that the nitrile gloves used for the growth preparation are other impurity contamination sources. We obtained a lightly n-type ([Si]=∼1016 cm−3) GaN layer, in which C, O, B, Fe, Mg, Al, Ca, Cr, Zn, Ni, Mn, and Ti impurity contents were below the detection limits of secondary ion mass spectrometry. Deep-level transient spectroscopy revealed that electron traps at EC − 0.26 and at EC − 0.59 eV were 2.7 × 1013 and 5.2 × 1014 cm−3, respectively. Moreover, the Hall effect analysis showed the acceptor-type defect-compensating donor content as approximately 2.7 × 1015 cm−3, resulting in a high electron mobility of HF-VPE GaN in the 30–710 K temperature range. Furthermore, we identified the Ca impurity as a deep acceptor, another killer defect leading to mobility collapse.
- 29 January 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124  (5)
Open AccessImpurity reduction in lightly doped n-type gallium nitride layer grown via halogen-free vapor-phase epitaxy
The development of gallium nitride (GaN) vertical-type metal-oxide-semiconductor field-effect transistors and p–i–n diode devices has gathered increasing attention. These devices require an n-type drift layer with a low doping level of 1016 cm−3 or less, minimized point defects inhibiting electron conduction, and a layer approximately 10 μm thick. Therefore, a practical method with a growth rate of at least several tens of μm/h and impurity concentrations of less than 1015 cm−3, except for that of dopants, is necessary. Halogen-free vapor-phase epitaxy (HF-VPE) has a high growth rate suitable for fabricating thick drift layers and utilizes a simple reaction between Ga vapor and ammonia gas (without a corrosive halogen gas), resulting in lower impurity levels. Herein, we eliminated the quartz content from the high-temperature zone to reduce the excess unintentional Si doping and identified that the nitrile gloves used for the growth preparation are other impurity contamination sources. We obtained a lightly n-type ([Si]=∼1016 cm−3) GaN layer, in which C, O, B, Fe, Mg, Al, Ca, Cr, Zn, Ni, Mn, and Ti impurity contents were below the detection limits of secondary ion mass spectrometry. Deep-level transient spectroscopy revealed that electron traps at EC − 0.26 and at EC − 0.59 eV were 2.7 × 1013 and 5.2 × 1014 cm−3, respectively. Moreover, the Hall effect analysis showed the acceptor-type defect-compensating donor content as approximately 2.7 × 1015 cm−3, resulting in a high electron mobility of HF-VPE GaN in the 30–710 K temperature range. Furthermore, we identified the Ca impurity as a deep acceptor, another killer defect leading to mobility collapse.
- Open Access
- 27 June 2022
- Published by Royal Society of Chemistry (RSC) in Nanoscale Advances
- Vol. 4  (18) , 3718-3724
Self-assembled single-crystal bimodal porous GaN exhibiting a petal effect: application as a sensing platform and substrate for optical devices
Petal effect (hydrophobicity and strong adhesion) exhibited by single-crystalline bimodal-porous-GaN creating high uniform attachment of chemical molecules and quantum dots.
- 27 June 2022
- Published by Royal Society of Chemistry (RSC) in Nanoscale Advances
- Vol. 4  (18) , 3718-3724
Open AccessSelf-assembled single-crystal bimodal porous GaN exhibiting a petal effect: application as a sensing platform and substrate for optical devices
Petal effect (hydrophobicity and strong adhesion) exhibited by single-crystalline bimodal-porous-GaN creating high uniform attachment of chemical molecules and quantum dots.
- Open Access
- 1 February 2022
- Published by IOP Publishing in Applied Physics Express
- Vol. 15  (2) , 026504
Reductions of implantation induced defects and leakage current by annealing in NH3/N2 atmosphere for Mg- and N-implanted GaN
We demonstrate the advantage of post-implantation annealing (PIA) in NH3/N2 for a p-n diode (PND) fabricated by the implantation of Mg and N ions into an n-type GaN layer by comparison with that annealed in N2. The leakage current for the PND with a reverse bias was lower in the case of NH3/N2 annealing. The cathodoluminescence spectrum measured for NH3/N2 annealing indicated a reduction in the densities of non-radiative recombination centers and nitrogen vacancy complexes. PIA in NH3/N2 is thus effective to suppress the density of implantation induced defects as leakage current sources.
- 1 February 2022
- Published by IOP Publishing in Applied Physics Express
- Vol. 15  (2) , 026504
Open AccessReductions of implantation induced defects and leakage current by annealing in NH3/N2 atmosphere for Mg- and N-implanted GaN
We demonstrate the advantage of post-implantation annealing (PIA) in NH3/N2 for a p-n diode (PND) fabricated by the implantation of Mg and N ions into an n-type GaN layer by comparison with that annealed in N2. The leakage current for the PND with a reverse bias was lower in the case of NH3/N2 annealing. The cathodoluminescence spectrum measured for NH3/N2 annealing indicated a reduction in the densities of non-radiative recombination centers and nitrogen vacancy complexes. PIA in NH3/N2 is thus effective to suppress the density of implantation induced defects as leakage current sources.
- 17 July 2020
- Published by IOP Publishing in Applied Physics Express
- Vol. 13  (8) , 085509
Growth of high-quality GaN by halogen-free vapor phase epitaxy
- 17 July 2020
- Published by IOP Publishing in Applied Physics Express
- Vol. 13  (8) , 085509
Growth of high-quality GaN by halogen-free vapor phase epitaxy
- 3 March 2020
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 22  (15) , 2632-2641
Tungsten carbide layers deposited on graphite substrates via a wet powder process as anti-parasitic-reaction coatings for reactor components in GaN growth
To prevent or suppress parasitic reactions (polycrystalline GaN deposition on the surface of susceptors) in the bulk GaN growth process, catalytic tungsten carbide (WC) layers are proposed as anti-parasitic-reaction (APR) coatings. An industrially feasible technique for producing APR coatings on a graphite substrate via a wet powder process is developed and the WC layers are confirmed to effectively prevent or suppress polycrystalline GaN deposition on APR-coated practical reactor components during the bulk growth processes of hydride vapor-phase epitaxy and halogen-free vapor-phase epitaxy. The mechanism of the APR function is investigated using X-ray photoelectron spectroscopy. It is found that a surface nitride layer forms on the topmost surface of the WC catalytic layer after annealing in an NH3 atmosphere. It is supposed that this nitride layer inhibits the adsorption of active nitrogen adsorbates and Ga species on the catalytic WC layers. The deposition of APR coatings on graphite substrates allows the growth of large bulk GaN crystals, which is necessary for low-cost GaN wafers for vertical GaN power devices.
- 3 March 2020
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 22  (15) , 2632-2641
Tungsten carbide layers deposited on graphite substrates via a wet powder process as anti-parasitic-reaction coatings for reactor components in GaN growth
To prevent or suppress parasitic reactions (polycrystalline GaN deposition on the surface of susceptors) in the bulk GaN growth process, catalytic tungsten carbide (WC) layers are proposed as anti-parasitic-reaction (APR) coatings. An industrially feasible technique for producing APR coatings on a graphite substrate via a wet powder process is developed and the WC layers are confirmed to effectively prevent or suppress polycrystalline GaN deposition on APR-coated practical reactor components during the bulk growth processes of hydride vapor-phase epitaxy and halogen-free vapor-phase epitaxy. The mechanism of the APR function is investigated using X-ray photoelectron spectroscopy. It is found that a surface nitride layer forms on the topmost surface of the WC catalytic layer after annealing in an NH3 atmosphere. It is supposed that this nitride layer inhibits the adsorption of active nitrogen adsorbates and Ga species on the catalytic WC layers. The deposition of APR coatings on graphite substrates allows the growth of large bulk GaN crystals, which is necessary for low-cost GaN wafers for vertical GaN power devices.
- 1 July 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58  (7) , 075509
Resistive heater element made of highly durable TaC-coated graphite for high-temperature and highly corrosive processes: application to MOCVD GaN epitaxial growth
Ultra-thick TaC-coated graphite prepared via a novel process was verified for use as a highly durable heater material in high-temperature and highly corrosive process environments such as those for SiC, GaN, and AlN bulk/epitaxial growth. As fundamental data for heater design, the temperature dependence of the electrical resistivity of the ultra-thick TaC layer was assessed. Estimation based on resistivity data indicates that the TaC-coated graphite heater element requires a slightly higher electrical current than that for conventional heaters. A coil-shaped ultra-thick TaC-coated heater for a MOCVD GaN growth system was fabricated using the proposed process. It was found to successfully heat the system to the target temperature for GaN epilayer growth. The quality of the MOCVD-grown GaN epilayers obtained with the TaC-coated heater was confirmed to be almost identical to that of those obtained with a conventional heater in terms of crystallinity, thickness homogeneity, intrinsic defects, impurity incorporation, and contamination.
- 1 July 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58  (7) , 075509
Resistive heater element made of highly durable TaC-coated graphite for high-temperature and highly corrosive processes: application to MOCVD GaN epitaxial growth
Ultra-thick TaC-coated graphite prepared via a novel process was verified for use as a highly durable heater material in high-temperature and highly corrosive process environments such as those for SiC, GaN, and AlN bulk/epitaxial growth. As fundamental data for heater design, the temperature dependence of the electrical resistivity of the ultra-thick TaC layer was assessed. Estimation based on resistivity data indicates that the TaC-coated graphite heater element requires a slightly higher electrical current than that for conventional heaters. A coil-shaped ultra-thick TaC-coated heater for a MOCVD GaN growth system was fabricated using the proposed process. It was found to successfully heat the system to the target temperature for GaN epilayer growth. The quality of the MOCVD-grown GaN epilayers obtained with the TaC-coated heater was confirmed to be almost identical to that of those obtained with a conventional heater in terms of crystallinity, thickness homogeneity, intrinsic defects, impurity incorporation, and contamination.