Gang Ji
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Gang Ji has a total of 144 co-authors. Here are the top co-authors by number of shared publications:
- Chaoyue Chen
Shanghai University
5 shared publications Hanlin Liao
5 shared publicationsXinliang Xie
5 shared publicationsEric Aubry
4 shared publicationsYingchun Xie
4 shared publicationsYu Ma
4 shared publications
Latest Publications
- Open Access
- 25 April 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Strong 3D-printed aluminium reinforced with ductile-transformable eutectic nano-skeleton
Lightweight metals for additive manufacturing remain constrained by limited strength-ductility synergy, restricting their use in high-performance structural applications. Here we report a design strategy for additively manufactured alloys based on ductile-transformable eutectic nano-skeletons (DT-ENS) enabled by non-equilibrium solidification. In a near-eutectic Al-Er system, we develop an alloy family containing a deformable Al3(Er,Mg) nano-skeleton as the primary strengthening architecture. Site-specific atomic substitution and long-range chemical ordering within the Al3(Er,Mg) skeleton are associated with deformation twinning and the strain-induced formation of 9R-type long-period stacking ordered structures, which enhance work-hardening of the skeleton and promote cooperative deformation with the α-Al matrix. Laser powder bed fusion yields Al-Er alloys with strengths of 600-700 MPa, together with good printability and useful ductility. These findings establish a new benchmark for structural additively manufactured aluminium alloys, provide a route for developing ductile intermetallics to overcome the strength-ductility trade-off in high-strength aluminium alloys, and demonstrate the role of additive manufacturing in uncovering new alloy systems and deformation mechanisms.
- 25 April 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Open AccessStrong 3D-printed aluminium reinforced with ductile-transformable eutectic nano-skeleton
Lightweight metals for additive manufacturing remain constrained by limited strength-ductility synergy, restricting their use in high-performance structural applications. Here we report a design strategy for additively manufactured alloys based on ductile-transformable eutectic nano-skeletons (DT-ENS) enabled by non-equilibrium solidification. In a near-eutectic Al-Er system, we develop an alloy family containing a deformable Al3(Er,Mg) nano-skeleton as the primary strengthening architecture. Site-specific atomic substitution and long-range chemical ordering within the Al3(Er,Mg) skeleton are associated with deformation twinning and the strain-induced formation of 9R-type long-period stacking ordered structures, which enhance work-hardening of the skeleton and promote cooperative deformation with the α-Al matrix. Laser powder bed fusion yields Al-Er alloys with strengths of 600-700 MPa, together with good printability and useful ductility. These findings establish a new benchmark for structural additively manufactured aluminium alloys, provide a route for developing ductile intermetallics to overcome the strength-ductility trade-off in high-strength aluminium alloys, and demonstrate the role of additive manufacturing in uncovering new alloy systems and deformation mechanisms.
- 13 March 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (23) , 23458-23469
Effect of Tempering Heat Treatment on the Microstructure and Mechanical Properties of Wire Arc Additively Manufactured H13 Steel
- 13 March 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (23) , 23458-23469
Effect of Tempering Heat Treatment on the Microstructure and Mechanical Properties of Wire Arc Additively Manufactured H13 Steel
- Open Access
- 22 November 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1)
High-temperature strength in an additively manufactured Al-based superalloy with stable nanoscale eutectic cellular networks
Metallic materials typically experience significant strength degradation at elevated temperatures. Traditional strengthening methods, which rely on thermally stable particle dispersion, exhibit limited effectiveness owing to the challenges in suppressing thermally activated dislocation motion. This work introduces a strategy for achieving exceptional high-temperature strength through a thermally stable nanoscale eutectic cellular network (ECN) enabled by additive manufacturing. A near-eutectic AlLaScZr alloy is developed for laser powder bed fusion, incorporating an Al-La nanoscale ECN and dense intracellular nanoprecipitates. This alloy demonstrates excellent printability and remarkable high-temperature yield strength above 0.6Tm (~250 MPa at 300 °C), outperforming conventional aluminium alloys by 2–5 times with minimal degradation after prolonged annealing. Compared with the conventional configuration of particle dispersion, the nanoscale ECN architecture enhances load-bearing capacity and strengthens aluminium by caging dislocation motion within ultrafine cells (~200 nm), effectively mitigating intrinsic high-temperature softening.
- 22 November 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1)
Open AccessHigh-temperature strength in an additively manufactured Al-based superalloy with stable nanoscale eutectic cellular networks
Metallic materials typically experience significant strength degradation at elevated temperatures. Traditional strengthening methods, which rely on thermally stable particle dispersion, exhibit limited effectiveness owing to the challenges in suppressing thermally activated dislocation motion. This work introduces a strategy for achieving exceptional high-temperature strength through a thermally stable nanoscale eutectic cellular network (ECN) enabled by additive manufacturing. A near-eutectic AlLaScZr alloy is developed for laser powder bed fusion, incorporating an Al-La nanoscale ECN and dense intracellular nanoprecipitates. This alloy demonstrates excellent printability and remarkable high-temperature yield strength above 0.6Tm (~250 MPa at 300 °C), outperforming conventional aluminium alloys by 2–5 times with minimal degradation after prolonged annealing. Compared with the conventional configuration of particle dispersion, the nanoscale ECN architecture enhances load-bearing capacity and strengthens aluminium by caging dislocation motion within ultrafine cells (~200 nm), effectively mitigating intrinsic high-temperature softening.
- Open Access
- 31 January 2025
- Published by Springer Nature in Research Square
Exceptional High-temperature Strength in an Additively Manufactured Al-based Superalloy with Stable Nanoscale Eutectic Cellular Network
Metallic materials typically experience significant strength degradation at elevated temperatures. Traditional strengthening methods, which rely on thermally stable particle dispersion, exhibit limited effectiveness owing to the challenges in suppressing thermally activated dislocation motion. This work introduces a novel strategy for achieving exceptional high-temperature strength through a thermally stable nanoscale eutectic cellular network (ECN) enabled by additive manufacturing. A near-eutectic AlLaScZr alloy is developed for laser powder bed fusion, incorporating an Al-La nanoscale ECN and dense intracellular nanoprecipitates. This alloy demonstrates excellent printability and remarkable high-temperature yield strength above 0.6 T m (~ 250 MPa at 300°C), outperforming conventional aluminium alloys by 2–5 times with minimal degradation after prolonged annealing. Compared with the conventional configuration of particle dispersion, the nanoscale ECN architecture enhances load-bearing capacity and strengthens aluminium by caging dislocation motion within ultrafine cells (~ 200 nm), effectively mitigating intrinsic high-temperature softening. The proposed transformative approach paves the way for designing next-generation heat-resistant alloys, unlocking new possibilities for additive manufacturing in high-temperature applications.
- 31 January 2025
- Published by Springer Nature in Research Square
Open AccessExceptional High-temperature Strength in an Additively Manufactured Al-based Superalloy with Stable Nanoscale Eutectic Cellular Network
Metallic materials typically experience significant strength degradation at elevated temperatures. Traditional strengthening methods, which rely on thermally stable particle dispersion, exhibit limited effectiveness owing to the challenges in suppressing thermally activated dislocation motion. This work introduces a novel strategy for achieving exceptional high-temperature strength through a thermally stable nanoscale eutectic cellular network (ECN) enabled by additive manufacturing. A near-eutectic AlLaScZr alloy is developed for laser powder bed fusion, incorporating an Al-La nanoscale ECN and dense intracellular nanoprecipitates. This alloy demonstrates excellent printability and remarkable high-temperature yield strength above 0.6 T m (~ 250 MPa at 300°C), outperforming conventional aluminium alloys by 2–5 times with minimal degradation after prolonged annealing. Compared with the conventional configuration of particle dispersion, the nanoscale ECN architecture enhances load-bearing capacity and strengthens aluminium by caging dislocation motion within ultrafine cells (~ 200 nm), effectively mitigating intrinsic high-temperature softening. The proposed transformative approach paves the way for designing next-generation heat-resistant alloys, unlocking new possibilities for additive manufacturing in high-temperature applications.
- Open Access
- 20 August 2024
- Published by MDPI AG in Inorganics
- Vol. 12 (8) , 227
Raman Spectroscopy and Microstructural Characterization of Hot-Rolled Copper/Graphene Composite Materials
Given the increase in current density in the constituent materials of electrical systems, improving the electrical conductivity of these materials, particularly copper (Cu), is crucial. This would also help to mitigate the heat generated by Joule heating. The incorporation of graphene (Gr) into a composite material (Cu/Gr) is a viable solution. However, to ensure the proper transfer of properties between the reinforcement and the matrix, several elements must be considered, including the orientation of the reinforcement. As a 2D material, controlling graphene’s orientation within the structure is essential but often overlooked. To address this issue, hot rolling was implemented to improve the alignment of the reinforcement. The inclusion of graphene led to a 12 HV increase in the material’s hardness, demonstrating a positive composite effect. Simultaneously, rolling increased the material’s hardness from 67.6 to 75.1 HV by introducing more dislocations into the material. To characterize the graphene’s alignment, polarized Raman spectroscopy was used. This technique highlighted the improved alignment of the reinforcement in the rolling direction, a change that was visible and confirmed by scanning electron microscopy micrographs.
- 20 August 2024
- Published by MDPI AG in Inorganics
- Vol. 12 (8) , 227
Open AccessRaman Spectroscopy and Microstructural Characterization of Hot-Rolled Copper/Graphene Composite Materials
Given the increase in current density in the constituent materials of electrical systems, improving the electrical conductivity of these materials, particularly copper (Cu), is crucial. This would also help to mitigate the heat generated by Joule heating. The incorporation of graphene (Gr) into a composite material (Cu/Gr) is a viable solution. However, to ensure the proper transfer of properties between the reinforcement and the matrix, several elements must be considered, including the orientation of the reinforcement. As a 2D material, controlling graphene’s orientation within the structure is essential but often overlooked. To address this issue, hot rolling was implemented to improve the alignment of the reinforcement. The inclusion of graphene led to a 12 HV increase in the material’s hardness, demonstrating a positive composite effect. Simultaneously, rolling increased the material’s hardness from 67.6 to 75.1 HV by introducing more dislocations into the material. To characterize the graphene’s alignment, polarized Raman spectroscopy was used. This technique highlighted the improved alignment of the reinforcement in the rolling direction, a change that was visible and confirmed by scanning electron microscopy micrographs.
- 12 May 2022
- Published by Springer Nature in Metals and Materials International
- Vol. 28 (11) , 2583-2595
Effect of Cr on Phase Transformation Behavior of Austenite in Fe-20Mn-9Al-1.2C-xCr Low-Density Steels During Isothermal Aging
- 12 May 2022
- Published by Springer Nature in Metals and Materials International
- Vol. 28 (11) , 2583-2595
Effect of Cr on Phase Transformation Behavior of Austenite in Fe-20Mn-9Al-1.2C-xCr Low-Density Steels During Isothermal Aging
- 18 March 2022
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 33 (13) , 10677-10692
On the study of morphological characteristics and growth mechanism of intermetallic compounds in ultrasonically fabricated Cu–Sn solder joints
- 18 March 2022
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 33 (13) , 10677-10692
On the study of morphological characteristics and growth mechanism of intermetallic compounds in ultrasonically fabricated Cu–Sn solder joints
- Open Access
- 31 January 2022
- Published by Taylor & Francis in Materials Research Letters
- Vol. 10 (3) , 141-148
Probing the effect of intragranular premature κ-carbide on incipient plasticity behavior in austenite-based Fe-Mn-Al-(Cr)-C steels
The effect of nanoscale intragranular premature κ-carbide precipitates, having an ordered structure but without chemical partitioning, on the incipient plasticity behavior of austenite in Fe-Mn-Al-(Cr)-C low-density steels was investigated by nanoindentation. We found that the incipient plasticity was dominated by a heterogeneous dislocation nucleation mechanism via atom-vacancy exchange. Although the content of κ-carbide decreased with Cr addition, its negligible effect on incipient plasticity strength was witnessed by the slightly increased shear stress for dislocation nucleation. Comparatively, the increased interstitial C atoms with Cr content in austenite enhanced lattice cohesions which impeded the nucleation events by increasing the requisite shear stress. GRAPHICAL ABSTRACT IMPACT STATEMENT Despite being one of the most important strengthening phases, nanoscale premature κ-carbide precipitates surprisingly have a negligible effect on incipient plasticity of austenite in Fe-Mn-Al-(Cr)-C low-density steels.
- 31 January 2022
- Published by Taylor & Francis in Materials Research Letters
- Vol. 10 (3) , 141-148
Open AccessProbing the effect of intragranular premature κ-carbide on incipient plasticity behavior in austenite-based Fe-Mn-Al-(Cr)-C steels
The effect of nanoscale intragranular premature κ-carbide precipitates, having an ordered structure but without chemical partitioning, on the incipient plasticity behavior of austenite in Fe-Mn-Al-(Cr)-C low-density steels was investigated by nanoindentation. We found that the incipient plasticity was dominated by a heterogeneous dislocation nucleation mechanism via atom-vacancy exchange. Although the content of κ-carbide decreased with Cr addition, its negligible effect on incipient plasticity strength was witnessed by the slightly increased shear stress for dislocation nucleation. Comparatively, the increased interstitial C atoms with Cr content in austenite enhanced lattice cohesions which impeded the nucleation events by increasing the requisite shear stress. GRAPHICAL ABSTRACT IMPACT STATEMENT Despite being one of the most important strengthening phases, nanoscale premature κ-carbide precipitates surprisingly have a negligible effect on incipient plasticity of austenite in Fe-Mn-Al-(Cr)-C low-density steels.
- 1 July 2020
- Published by Elsevier in Scripta Materialia
- Vol. 183, 86-90
From 1D to 2D arrangements of graphite flakes in an aluminium matrix composite: Impact on thermal properties
- 1 July 2020
- Published by Elsevier in Scripta Materialia
- Vol. 183, 86-90
From 1D to 2D arrangements of graphite flakes in an aluminium matrix composite: Impact on thermal properties