LVLyudmila V. Volkova

Lyudmila V. Volkova

*This is an algorithmically generated author record based on publicly available information.

Lyudmila V. Volkova has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Acoustic properties of 15-5 PH maraging steel after energy deposition

    by Olga V. Muravieva, Vitaly V. Muraviev, Lyudmila V. Volkova, Aleksey L. Vladykin, Konstantin Yu. Belosludtsev, Udmurt Federal Research Center of the Ural branch of the RAS, Муравьев Виталий Васильевич

    The study of the acoustic properties of maraging steels operated under various energy force and temperature actions is a critical task, since it is the method of acoustic structuroscopy that provides the most reliable connection with the structure, stress-strain state and mechanical properties of steels. The paper is devoted to research of the acoustic properties of the 15-5 PH maraging steel samples under various types of heat treatment under the conditions of mechanical tensile and cyclic loads. Samples of the 15-5 PH maraging steel were studied in three structural states: solid solution annealing and subsequent aging at 470 and 565 °C; during tensile tests; during cyclic tension-compression loading. The research used a unique scientific installation “Information-measuring complex for investigation of acoustic properties of materials and products”. It implements the acoustic mirror-shadow multiple reflections method using electromagnetic-acoustic and piezoelectric transducers based on polyvinylidene fluoride film to excite and receive waves and allows determining the velocity of wave propagation with an error of no more than 2 m/s. The acoustic (wave velocity, elastic moduli, electromagnetic-acoustical (EMA) transformation coefficients, acoustic anisotropy coefficients, acoustoelastic coupling coefficients) and electromagnetic (coercive force and electrical conductivity) characteristics of the samples were examined. The samples were studied in the initial state (before loading); stepwise in the process of tensile loads and subsequent unloading; after tensile tests; during cyclic tension-compression loading. It was revealed that the following acoustic parameters of 15-5 PH steel samples are the greatest structural sensitivity to mechanical tensile load and cyclic loading: transverse wave velocity, Poisson’s ratio, double EMA-transformation coefficient, and acoustic anisotropy coefficient.


  • Open Access

    Measurement of Residual Stresses of Locomotive Wheel Treads During the Manufacturing Technological Cycle

    by Vitaly V. Muravev, Olga V. Muraveva, Ludmila V. Volkova, Milan Sága, Zuzana Ságová

    The production of two-wheeled rolling stock represents, at first glance, a simple assembly process that significantly affects the overall functionality and safety of the vehicle. This is due to residual stresses that arise after assembly by pressing the wheel on the axle. The state of stress after assembly remains in the design has a decisive influence on the load-bearing capacity of the two-wheel drive, its lifespan but also the transfer of the pulling force in the case of locomotives. Therefore, it is very important to find suitable methods for determining residual stresses. Numerical and experimental approaches are already in place to gain information on the state of stress after compression, or during a real operation. The developed techniques and tools for estimation of residual stresses in locomotive wheel treads based on the acoustoelasticity effect using electromagnetic acoustic transformation are described in the paper. The original results of residual stress measurement in the treads during a technological cycle of locomotive wheel pair manufacturing are presented.


  • Open Access

    Numerical simulation of electromagnetic-acoustic transformation using Jiles-Atherton magnetic hysteresis model

    by Yu V Myshkin, L V Volkova

    The paper presents the results of numerical simulation of electromagnetic-acoustic transformation using Jiles-Atherton magnetic hysteresis on the example of excitation and reception of a transverse wave through the thickness of the reference block CO-2 based on the W-shaped magnetic core and inductor in the form of a meander coil with in-phased conductors. Distributions and graphs of time dependence for the magnetic field, the field of eddy currents and the field of elastic deformations are given in comparison with the classical modeling approaches. Satisfactory convergence of the simulation results with experimental data was established by the example of the signal received by the inductor, the distribution of the normal component of the magnetic flux density in the gap of inductor positioning and the calculated double transformation coefficient.


  • Strain Stress Model of the Rail with Crack in its Head and Estimation of its Operational Lifetime

    by Vitaliy V. Muravev, Kirill A. Tapkov, Ludmila V. Volkova, Andrei V. Platunov

    The most common reason of the fatigue crack appearance is the presence of stresses in the rail. The process of stress strain state simulation for the R65 rail is presented in the paper. Values of residual stresses were modeled and chosen to be maximum allowed by GOST (State Standard): -77 MPa in the rail head, -125 MPa in the web and 106 MPa in rail foot. These stresses match the value-77 MPa measured by the acoustoelastic method from the center of the rolling surface of the rail. The influence of the crack at the highest level of the stress strain state was studied in cases of the maximum train load and its absence. According to results of modeling, stresses in the sharp edge of the crack can exceed the lowest acceptable by GOST (State Standard) value of the yield strength by more than 5 times in case of the presence of the train load. In case of the absence of the train load, the crack does not have a significant influence on the stress strain state. The modelling process was also used to study the influence of the installation temperature difference on the operational lifetime of the rail. The paper presents the description of the influence between the installation temperature difference and the crack initiation. According to modeling results and the rail defect catalogue, rails with the lowest acceptable mechanical characteristics are prohibited to be used after 300∙109 kg and higher tonnage.


  • Open Access

    Device and Methods for Measuring of Acoustic Anisotropy and the Residual Stress in the Main Gas Pipelines’ Metal

    by L. V. Volkova, O. V. Murav’eVa, V. V. Murav’eV, I. V. Buldakova

    One of the main conditions of safe operation of gas pipelines is the use of non-destructive diagnostic methods. Particularly important problem is the earlier operational diagnosis of pipes’ material of main gas pipelines based on the evaluation of the stress-strain state, elastic moduli and properties anisotropy by acoustic methods. The aim of the work is to develop methods for acoustic assessment of the stress-strain state, the elastic moduli and the properties anisotropy of pipeline material and to study these characteristics in different sections of main pipelines using a device based on contactlessEMAtransducers.Methods are implemented using specialized equipment (the structurescopeSEMA) and non-contact electromagnetic acoustic transducers. As an object of research, we used fragments – the cuttings of gas pipelines with circumferential welds both after fabrication and removed from service with stress corrosion cracking, including ones with corrosion damage and without visible damage.The method of determining the plane stress-strain state of pipeline elements is based on the phenomenon of acoustoelasticity – the dependence of the propagation velocity of ultrasonic waves on mechanical stresses. The method for determining the elastic characteristics of materials and the anisotropy of their properties is based on the relationship between the velocities of ultrasonic waves and the elastic properties of the medium. Both techniques are implemented by sounding the sample in one section using a longitudinal wave and two shear waves with mutually perpendicular polarization planes coinciding with the main stresses, and measuring their propagation times.It is shown that the stress state distribution both in the circumferential direction and along the generatrix is uneven which is caused by the peculiarities of samples (presence of a welded joint, stress corrosion cracking, long-term operation). The smallest acoustic anisotropy is observed for the Young's modulus. The anisotropy of the properties of most samples is in the range of 12–14 % for shear modulus, 9–10 % for Young’s modulus, 13–15 % for Poisson’s ratio. For samples with stress corrosion cracking a sharp decrease in the anisotropy coefficient is observed which makes it possible to use the indicated characteristics as informative parameters in detecting stress corrosion cracking.A feature of the proposed methods is high accuracy, due to the absence of necessity to determine the material density and precision measurement of its thickness, the measurement error of which is significant by known methods.Keywords:main gas pipeline, elastic moduli, acoustic anisotropy of properties, the biaxial stress-strain state, longitudinal and transversal waves.


  • Acoustic Assessment of the Internal Stress and Mechanical Properties of Differentially Hardened Rail

    by V. V. Murav’EV, L. V. Volkova, A. V. Platunov, L. V. Gushchina

    An acoustic method of determining the longitudinal residual stress in DT-350 differentially hardened rail is described. The measurements are made by means of an electromagnetic–acoustic converter on...


  • Influence of the mechanical anisotropy of thin steel sheets on the parameters of Lamb waves

    by V. V. Murav’EV, O. V. Murav’EVa, L. V. Volkova

    The textural anisotropy in thin low-carbon 08ps and DC01 steel sheet is investigated by an electromagnetic–acoustic method. The sensitivity of Lamb waves of symmetric and antisymmetric zero-order modes to change in the elastic modulus of the medium is determined. The relation between the anisotropy of the properties and the mechanical characteristics of the metal sheet is established.


  • The distribution of residual stresses in railroad wheels after electrocontact strengthening of the rolling surface

    by V. V. Murav’EV, S. Yu. Petrov, L. V. Volkova

    A procedure for the quality control of residual stresses in the rims of rolled wheels and locomotive tires via the ultrasound method using electromagnetic–acoustic excitation–reception of elastic...


  • Ultrasonic in-process control of residual stresses in locomotive tires

    by V. V. Muravyev, L. V. Volkova, M. A. Lapchenko

    The methods and means of controlling residual stresses in locomotive tires, developed on the basis of acoustoelasticity and involving electromagnetic acoustic transformation, are described. The...