Takumi Inaba
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Takumi Inaba has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Hiroshi Oka
National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Ibaraki 305-8468, Japan
10 shared publications - Kimihiko Kato
National Institute of Advanced Industrial Science and Technology Tsukuba Center Tsukuba Central, Tsukuba, 305-8568, JAPAN
8 shared publications - Shota Iizuka
National Institute of Advanced Industrial Science and Technology Tsukuba Center Tsukuba Central, Tsukuba, 305-8568, JAPAN
8 shared publications - Hidehiro Asai
National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Japan
7 shared publications - Takahiro Mori
National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Japan
7 shared publications Shunsuke Shitakata
National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Ibaraki, 305-8568, Japan
5 shared publications
Latest Publications
- Open Access
- 17 April 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (11)
Clarifying the physical origin of long-period charge fluctuations in Si fin-type quantum dots
Si quantum bits (qubits) have attracted attention as the building block of highly integrated quantum computers due to their compatibility with the modern complementary metal-oxide-semiconductor (CMOS) technology. For the practical operation of quantum computers, it is important not only to pursue the highest performance of qubits, but also to minimize their long-period instability in performance as they necessitate the frequent monitoring and calibration of parameters. With the Si spin qubits, fluctuations of performance over a period of minutes or even hours have been reported, which originate from the charge fluctuations. However, the cause-and-effect of long-period charge fluctuations in Si spin qubits has not been thoroughly discussed. This paper provides a brief overview of the Si spin qubit technology, focusing on the issue of long-period charge fluctuations, and presents our experimental results to clarify the physical origin of long-period charge fluctuations in fin-type quantum dots through random telegraph noise (RTN) characterization.
- 17 April 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (11)
Open AccessClarifying the physical origin of long-period charge fluctuations in Si fin-type quantum dots
Si quantum bits (qubits) have attracted attention as the building block of highly integrated quantum computers due to their compatibility with the modern complementary metal-oxide-semiconductor (CMOS) technology. For the practical operation of quantum computers, it is important not only to pursue the highest performance of qubits, but also to minimize their long-period instability in performance as they necessitate the frequent monitoring and calibration of parameters. With the Si spin qubits, fluctuations of performance over a period of minutes or even hours have been reported, which originate from the charge fluctuations. However, the cause-and-effect of long-period charge fluctuations in Si spin qubits has not been thoroughly discussed. This paper provides a brief overview of the Si spin qubit technology, focusing on the issue of long-period charge fluctuations, and presents our experimental results to clarify the physical origin of long-period charge fluctuations in fin-type quantum dots through random telegraph noise (RTN) characterization.
- Open Access
- 1 March 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (1)
An electric characterization method for identifying the number and position of unintended defect dots formed in silicon quantum dot devices
We propose a simple and generic electrical characterization method to identify the number and position of quantum dots (QDs) and to distinguish between the designed and unintentionally formed defects in silicon QD devices. This method uses single-electron current mapping in relation to plunger and barrier gate voltages. The Coulomb oscillation lines exhibited in the mapping are slanted because of the capacitive coupling between the QDs and the barrier gate. The lines with different slopes originated from different QDs, which allowed us to count the number of QDs in the device. In addition, the slope value allowed the estimation of the QD position. The lines with the largest absolute slope values likely originate from the designed QD, whereas others originate from unintentionally formed QDs. This method facilitates the development of silicon qubits during the process and fabrication optimization stages.
- 1 March 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (1)
Open AccessAn electric characterization method for identifying the number and position of unintended defect dots formed in silicon quantum dot devices
We propose a simple and generic electrical characterization method to identify the number and position of quantum dots (QDs) and to distinguish between the designed and unintentionally formed defects in silicon QD devices. This method uses single-electron current mapping in relation to plunger and barrier gate voltages. The Coulomb oscillation lines exhibited in the mapping are slanted because of the capacitive coupling between the QDs and the barrier gate. The lines with different slopes originated from different QDs, which allowed us to count the number of QDs in the device. In addition, the slope value allowed the estimation of the QD position. The lines with the largest absolute slope values likely originate from the designed QD, whereas others originate from unintentionally formed QDs. This method facilitates the development of silicon qubits during the process and fabrication optimization stages.
- Open Access
- 24 February 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (4) , 044001
BSIM4 modeling of drain voltage, gate length, and temperature-dependent I d – V g characteristics of bulk MOSFETs at cryogenic temperature using a conditional diffusion neural network
In this study, a neural-network-based approach was developed to model the drain-voltage, gate-length, and temperature-dependent drain-current–gate-voltage ( I d – V g ) characteristics of metal-oxide-semiconductor field-effect transistors (MOSFETs) at cryogenic temperatures. Using experimental data obtained at cryogenic temperatures, fifteen BSIM4 parameters were automatically tuned through this approach. As a result, a single set of BSIM4 parameters was extracted that reproduced the I d – V g characteristics of short-channel bulk MOSFETs with gate lengths of 90–250 nm over the temperature range of 4–100 K. These results contribute to continuity and convergence in Cryo-CMOS circuit simulations under self-heating effects, facilitating precise qubit control and the realization of large-scale fault-tolerant quantum computers.
- 24 February 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (4) , 044001
Open AccessBSIM4 modeling of drain voltage, gate length, and temperature-dependent I d – V g characteristics of bulk MOSFETs at cryogenic temperature using a conditional diffusion neural network
In this study, a neural-network-based approach was developed to model the drain-voltage, gate-length, and temperature-dependent drain-current–gate-voltage ( I d – V g ) characteristics of metal-oxide-semiconductor field-effect transistors (MOSFETs) at cryogenic temperatures. Using experimental data obtained at cryogenic temperatures, fifteen BSIM4 parameters were automatically tuned through this approach. As a result, a single set of BSIM4 parameters was extracted that reproduced the I d – V g characteristics of short-channel bulk MOSFETs with gate lengths of 90–250 nm over the temperature range of 4–100 K. These results contribute to continuity and convergence in Cryo-CMOS circuit simulations under self-heating effects, facilitating precise qubit control and the realization of large-scale fault-tolerant quantum computers.
- 16 February 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (3) , 03SP27
Anomalous variability of subthreshold characteristics in bulk and silicon on insulator MOSFETs at cryogenic temperatures
The variability of subthreshold characteristics in bulk and fully depleted silicon on insulator (FDSOI) MOSFETs fabricated using 65 nm CMOS technology was measured at 1.5 K and 300 K using addressable transistor arrays. Measurements were conducted at a nominal temperature of 1.5 K, which is the lowest achievable set temperature of our cryogenic measurement system, in order to minimize thermal contributions. While the variability in FDSOI is smaller than that in bulk, anomalous subthreshold variability was observed in both bulk and FDSOI at 1.5 K. Similar anomalous subthreshold variability at 1.5 K, as previously reported, was confirmed for two different technologies, suggesting the existence of a common mechanism independent of process technologies.
- 16 February 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (3) , 03SP27
Anomalous variability of subthreshold characteristics in bulk and silicon on insulator MOSFETs at cryogenic temperatures
The variability of subthreshold characteristics in bulk and fully depleted silicon on insulator (FDSOI) MOSFETs fabricated using 65 nm CMOS technology was measured at 1.5 K and 300 K using addressable transistor arrays. Measurements were conducted at a nominal temperature of 1.5 K, which is the lowest achievable set temperature of our cryogenic measurement system, in order to minimize thermal contributions. While the variability in FDSOI is smaller than that in bulk, anomalous subthreshold variability was observed in both bulk and FDSOI at 1.5 K. Similar anomalous subthreshold variability at 1.5 K, as previously reported, was confirmed for two different technologies, suggesting the existence of a common mechanism independent of process technologies.
- 13 January 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (1) , 01SP14
Demonstration of n-type WSe 2 FET via surface plasma treatment and neural network-assisted device modeling for single-channel WSe 2 CMOS circuit applications
This study demonstrates an n-type WSe 2 FET achieved by introducing selenium (Se) vacancies in the source/drain (S/D) regions. The Se vacancies act as electron dopants, forming electron injection layers beneath the S/D electrodes and enabling efficient carrier transport in the WSe 2 channel. The fabricated devices exhibit clear n-type conduction, representing a key step toward WSe 2 -based CMOS technology. Furthermore, neural network (NN)-assisted device modeling accurately reproduces the electrical characteristics of the n- and p-type WSe 2 FETs, offering a data-driven framework for circuit-level simulation and design of emerging devices.
- 13 January 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (1) , 01SP14
Demonstration of n-type WSe 2 FET via surface plasma treatment and neural network-assisted device modeling for single-channel WSe 2 CMOS circuit applications
This study demonstrates an n-type WSe 2 FET achieved by introducing selenium (Se) vacancies in the source/drain (S/D) regions. The Se vacancies act as electron dopants, forming electron injection layers beneath the S/D electrodes and enabling efficient carrier transport in the WSe 2 channel. The fabricated devices exhibit clear n-type conduction, representing a key step toward WSe 2 -based CMOS technology. Furthermore, neural network (NN)-assisted device modeling accurately reproduces the electrical characteristics of the n- and p-type WSe 2 FETs, offering a data-driven framework for circuit-level simulation and design of emerging devices.
- 28 April 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (17)
Mechanism of the negative linear temperature coefficient of resistance in defective nanocarbon materials
This paper presents the evidential results of the negative linear temperature coefficient mechanism commonly observed in defect-containing nanocarbon materials. Single-walled carbon nanotubes (CNTs) were annealed at high temperatures ranging from 1200 to 3000 °C. These samples exhibited a general hopping conduction-like behavior between the CNTs in the pristine state. However, the high-temperature annealed samples exhibited a resistance change with a negative temperature coefficient. Recently, we proposed that the origin of this negative linear temperature dependence of resistance behavior is a scattering phenomenon due to Friedel oscillations occurring in a flat graphene sheet containing defects. In fact, from the cross-sectional high-resolution transmission electron microscopy images, we found that the tube structure of the CNTs collapsed and fused with each other in the high-temperature annealed samples, revealing a stacked, flat graphite structure. These results show that the Friedel scattering phenomenon originates from the negative linear temperature coefficient widely observed in defect-containing nanocarbon materials. This negative linear temperature coefficient provides important information on the application of nanocarbon materials to thermistors, which have recently attracted significant attention, and on the optimal design guidelines for such thermistors. Moreover, the nonzero current and nondivergent resistance behavior based on the Friedel scattering phenomenon provide more stable measurement conditions for the quantum research field, including quantum computing, cryptography, and communications.
- 28 April 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (17)
Mechanism of the negative linear temperature coefficient of resistance in defective nanocarbon materials
This paper presents the evidential results of the negative linear temperature coefficient mechanism commonly observed in defect-containing nanocarbon materials. Single-walled carbon nanotubes (CNTs) were annealed at high temperatures ranging from 1200 to 3000 °C. These samples exhibited a general hopping conduction-like behavior between the CNTs in the pristine state. However, the high-temperature annealed samples exhibited a resistance change with a negative temperature coefficient. Recently, we proposed that the origin of this negative linear temperature dependence of resistance behavior is a scattering phenomenon due to Friedel oscillations occurring in a flat graphene sheet containing defects. In fact, from the cross-sectional high-resolution transmission electron microscopy images, we found that the tube structure of the CNTs collapsed and fused with each other in the high-temperature annealed samples, revealing a stacked, flat graphite structure. These results show that the Friedel scattering phenomenon originates from the negative linear temperature coefficient widely observed in defect-containing nanocarbon materials. This negative linear temperature coefficient provides important information on the application of nanocarbon materials to thermistors, which have recently attracted significant attention, and on the optimal design guidelines for such thermistors. Moreover, the nonzero current and nondivergent resistance behavior based on the Friedel scattering phenomenon provide more stable measurement conditions for the quantum research field, including quantum computing, cryptography, and communications.
- Open Access
- 11 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 13, 308-316
Hot Carrier Degradation in Si n-MOSFETs at Cryogenic Temperatures
This study experimentally investigated hot carrier degradation (HCD) in Si-MOSFETs at cryogenic temperatures. Stress was applied to the devices at 4 K and 300 K, followed by temperature-dependent characterization from 4 K to 300 K to evaluate the degradation mechanism. The results indicated that at 4 K, the effect of HCD on current-voltage characteristics is attributable to band-edge states, whereas at 300 K, it is primarily due to deep states. Despite the temperature at which HCD occurred, both states are induced simultaneously by hot carriers. Deuterium termination of dangling bonds mitigates HCD even at 4 K, where degradation is caused by band-edge states. These results suggest that the band-edge states and deep states should be considered in conjunction, rather than in isolation, to fully understand the degradation behavior.
- 11 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 13, 308-316
Open AccessHot Carrier Degradation in Si n-MOSFETs at Cryogenic Temperatures
This study experimentally investigated hot carrier degradation (HCD) in Si-MOSFETs at cryogenic temperatures. Stress was applied to the devices at 4 K and 300 K, followed by temperature-dependent characterization from 4 K to 300 K to evaluate the degradation mechanism. The results indicated that at 4 K, the effect of HCD on current-voltage characteristics is attributable to band-edge states, whereas at 300 K, it is primarily due to deep states. Despite the temperature at which HCD occurred, both states are induced simultaneously by hot carriers. Deuterium termination of dangling bonds mitigates HCD even at 4 K, where degradation is caused by band-edge states. These results suggest that the band-edge states and deep states should be considered in conjunction, rather than in isolation, to fully understand the degradation behavior.
- Open Access
- 20 January 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (2)
Effect of interface trap charge on Coulomb oscillation in MOS-type quantum dots
We have theoretically investigated the effect of an interface trap charge (ITC) on the Coulomb oscillation characteristics in a Si MOS-type quantum dot (Q-dot). We found that the ITC causes a variation in the fundamental characteristics of the Coulomb oscillation: a peak position, a peak height, and a peak interval. We clarified that the dependence of each variation on the ITC position is different from that of the other because of their different physical origins. We also discussed the amount of the peak position variation from the viewpoint of the operation of the Q-dots required in Si quantum computers (QCs). Mitigating the large variation caused by the ITC will be a critical issue for achieving large-scale Si QCs.
- 20 January 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (2)
Open AccessEffect of interface trap charge on Coulomb oscillation in MOS-type quantum dots
We have theoretically investigated the effect of an interface trap charge (ITC) on the Coulomb oscillation characteristics in a Si MOS-type quantum dot (Q-dot). We found that the ITC causes a variation in the fundamental characteristics of the Coulomb oscillation: a peak position, a peak height, and a peak interval. We clarified that the dependence of each variation on the ITC position is different from that of the other because of their different physical origins. We also discussed the amount of the peak position variation from the viewpoint of the operation of the Q-dots required in Si quantum computers (QCs). Mitigating the large variation caused by the ITC will be a critical issue for achieving large-scale Si QCs.
- Open Access
- 2 December 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (12) , 12SP19
Neural-network-based prediction of cryogenic BSIM4 model parameters from small datasets
Neural-network-based prediction of BSIM4 model parameters for current-voltage (I-V) characteristics of short-channel bulk MOSFETs at 4 K was examined. Combining two neural network (NN) models and the least-squares method enabled the extraction of model parameters from only 4 experimentally obtained Id-Vg characteristics of 2 cryogenic MOSFETs, contributing to reducing time and financial costs for cryogenic device modeling. The proposed protocol provided lower root-mean-squared errors than the case where the least-squares method was solely employed. The superiority of the proposed protocol became evident as the number of model parameters increased, attributed to NNs providing good initial guesses for the least-squares method. As a result, cryogenic MOSFETs’ characteristics were fit by BSIM4 with the 6.6% error. This study also emphasizes the superiority of generative NN models over regression NN models for model parameter extraction by demonstrating the parameter extraction for highly correlated model parameters relating to threshold voltage.
- 2 December 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (12) , 12SP19
Open AccessNeural-network-based prediction of cryogenic BSIM4 model parameters from small datasets
Neural-network-based prediction of BSIM4 model parameters for current-voltage (I-V) characteristics of short-channel bulk MOSFETs at 4 K was examined. Combining two neural network (NN) models and the least-squares method enabled the extraction of model parameters from only 4 experimentally obtained Id-Vg characteristics of 2 cryogenic MOSFETs, contributing to reducing time and financial costs for cryogenic device modeling. The proposed protocol provided lower root-mean-squared errors than the case where the least-squares method was solely employed. The superiority of the proposed protocol became evident as the number of model parameters increased, attributed to NNs providing good initial guesses for the least-squares method. As a result, cryogenic MOSFETs’ characteristics were fit by BSIM4 with the 6.6% error. This study also emphasizes the superiority of generative NN models over regression NN models for model parameter extraction by demonstrating the parameter extraction for highly correlated model parameters relating to threshold voltage.