Yimin Lei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yimin Lei has a total of 120 co-authors. Here are the top co-authors by number of shared publications:
Xiaohua Ma
11 shared publicationsQing Zhu
8 shared publications- Xiaohua Ma
Xidian University
8 shared publications - Jie Sun
Key Laboratory of Applied Surface and Colloid Chemistry (Ministry of Education) Shaanxi Engineering Lab for Advanced Energy Technology Shaanxi Key Laboratory for Advanced Energy Devices School of Materials Science and Engineering Shaanxi Normal University Xi'an China
7 shared publications Yuxiang Wei
7 shared publicationsPeng Zhong
School of Advanced Materials and Nanotechnology, Xidian University, Xi’an, China
5 shared publications
Latest Publications
- Open Access
- 28 July 2026
- Published by Wiley in Advanced Materials Interfaces
- Vol. 13 (17)
Cation‐π Interaction‐Based Biointerface for Low‐Cost PD‐1 Detection Toward NSCLC Immunotherapy Monitoring
Programmed death‐1 (PD‐1) is a key biomarker for monitoring therapeutic response and resistance in non‐small cell lung cancer (NSCLC) immunotherapy. Achieving highly sensitive, real‐time detection of PD‐1 is crucial for early prediction of treatment resistance and disease recurrence. However, current methods such as ELISA suffer from limitations in sensitivity, speed, and cost. To address these challenges, we develop a label‐free biosensor based on semiconducting single‐walled carbon nanotube field‐effect transistors (CNT‐FETs). The sensing interface is designed by wrapping s‐SWCNTs with poly[9‐(1‐octylnonyl)‐9H‐carbazole] (PCz), enabling immobilization of anti‐PD‐1 antibodies via cation‐π interactions. XPS analysis confirms antibody immobilization via reversible binding energy shifts in C 1s and N 1s spectra upon salt treatment, consistent with cation‐π interactions, further validated by NaCl and imidazole competition assays. Using this strategy, the sensor achieves a detection limit of 8.39 fg/mL for murine PD‐1—three orders of magnitude lower than ELISA, along with good specificity and favorable regeneration capability. In human serum, it shows promising performance, with 12 out of 14 NSCLC patient samples (85.7%) exhibiting good linear correlation. With rapid response, low cost, and simple operation, this platform offers a reliable strategy for point‐of‐care PD‐1 monitoring during NSCLC immunotherapy.
- 28 July 2026
- Published by Wiley in Advanced Materials Interfaces
- Vol. 13 (17)
Open AccessCation‐π Interaction‐Based Biointerface for Low‐Cost PD‐1 Detection Toward NSCLC Immunotherapy Monitoring
Programmed death‐1 (PD‐1) is a key biomarker for monitoring therapeutic response and resistance in non‐small cell lung cancer (NSCLC) immunotherapy. Achieving highly sensitive, real‐time detection of PD‐1 is crucial for early prediction of treatment resistance and disease recurrence. However, current methods such as ELISA suffer from limitations in sensitivity, speed, and cost. To address these challenges, we develop a label‐free biosensor based on semiconducting single‐walled carbon nanotube field‐effect transistors (CNT‐FETs). The sensing interface is designed by wrapping s‐SWCNTs with poly[9‐(1‐octylnonyl)‐9H‐carbazole] (PCz), enabling immobilization of anti‐PD‐1 antibodies via cation‐π interactions. XPS analysis confirms antibody immobilization via reversible binding energy shifts in C 1s and N 1s spectra upon salt treatment, consistent with cation‐π interactions, further validated by NaCl and imidazole competition assays. Using this strategy, the sensor achieves a detection limit of 8.39 fg/mL for murine PD‐1—three orders of magnitude lower than ELISA, along with good specificity and favorable regeneration capability. In human serum, it shows promising performance, with 12 out of 14 NSCLC patient samples (85.7%) exhibiting good linear correlation. With rapid response, low cost, and simple operation, this platform offers a reliable strategy for point‐of‐care PD‐1 monitoring during NSCLC immunotherapy.
- Open Access
- 22 July 2026
- Published by Wiley in Advanced Materials Interfaces
- Vol. 13 (16) , e70600
Bandgap‐Dependent Band‐to‐Band Tunneling in Carbon Nanotube Transistors
Single‐walled carbon nanotubes (SWCNTs) are considered promising channel materials for post‐Moore nanoelectronics due to their excellent carrier transport properties. However, the intrinsic chirality polydispersity of synthetic SWCNTs leads to significant bandgap non‐uniformity, which fundamentally limits the off‐state performance and integration density of carbon nanotube thin‐film transistors (CNT‐TFTs). Here, we systematically investigate the influence of statistical bandgap distributions on the transport characteristics and leakage mechanisms of CNT‐TFTs using three representative semiconducting SWCNT systems: single‐chirality‐enriched wide‐bandgap (6,5) SWCNTs, mixed‐chirality high‐pressure carbon monoxide (HiPco) SWCNTs with an intermediate average bandgap, and mixed‐chirality arc‐discharge SWCNTs with a smaller average bandgap. We show that narrow‐bandgap SWCNT networks exhibit higher on‐state currents due to reduced Schottky barriers but suffer from pronounced band‐to‐band tunneling (BTBT) under high electric fields, resulting in degraded on/off ratios and subthreshold stability. In contrast, devices based on single‐chirality‐enriched (6,5) SWCNTs effectively suppress BTBT, maintaining ultra‐low off‐state currents (I off < 10 −11 A) and high on/off ratios (>10 6 ) even at high drain bias. These findings provide a material‐selection guideline for carbon‐based integrated circuits: wide‐bandgap, single‐chirality‐enriched SWCNTs are advantageous for leakage‐sensitive low‐power logic applications, whereas mixed‐chirality SWCNT networks with smaller average bandgaps are more suitable for high‐drive‐current analog and radio‐frequency electronics.
- 22 July 2026
- Published by Wiley in Advanced Materials Interfaces
- Vol. 13 (16) , e70600
Open AccessBandgap‐Dependent Band‐to‐Band Tunneling in Carbon Nanotube Transistors
Single‐walled carbon nanotubes (SWCNTs) are considered promising channel materials for post‐Moore nanoelectronics due to their excellent carrier transport properties. However, the intrinsic chirality polydispersity of synthetic SWCNTs leads to significant bandgap non‐uniformity, which fundamentally limits the off‐state performance and integration density of carbon nanotube thin‐film transistors (CNT‐TFTs). Here, we systematically investigate the influence of statistical bandgap distributions on the transport characteristics and leakage mechanisms of CNT‐TFTs using three representative semiconducting SWCNT systems: single‐chirality‐enriched wide‐bandgap (6,5) SWCNTs, mixed‐chirality high‐pressure carbon monoxide (HiPco) SWCNTs with an intermediate average bandgap, and mixed‐chirality arc‐discharge SWCNTs with a smaller average bandgap. We show that narrow‐bandgap SWCNT networks exhibit higher on‐state currents due to reduced Schottky barriers but suffer from pronounced band‐to‐band tunneling (BTBT) under high electric fields, resulting in degraded on/off ratios and subthreshold stability. In contrast, devices based on single‐chirality‐enriched (6,5) SWCNTs effectively suppress BTBT, maintaining ultra‐low off‐state currents (I off < 10 −11 A) and high on/off ratios (>10 6 ) even at high drain bias. These findings provide a material‐selection guideline for carbon‐based integrated circuits: wide‐bandgap, single‐chirality‐enriched SWCNTs are advantageous for leakage‐sensitive low‐power logic applications, whereas mixed‐chirality SWCNT networks with smaller average bandgaps are more suitable for high‐drive‐current analog and radio‐frequency electronics.
- 9 April 2026
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 13 (2)
Electric field-directed anisotropic failure of β -Ga2O3
As one of the critical materials for ultra-high-voltage power devices, β-gallium oxide (β-Ga2O3) faces significant reliability challenges. Under the coupled effects of repeated electrical stress and high-temperature thermal fields, the stability of this material directly determines the reliability of power devices under extreme service conditions. However, to date, atomic-scale real-time observations and mechanistic explanations of the failure process of this material under coupled electro-thermal fields remain lacking. In this study, using in situ transmission electron microscopy (in situ TEM) under coupled thermal-electrical field (500 °C and 1 V bias), we directly observed the anisotropic failure of β-Ga2O3 along low-index planes such as (200). Controlled decoupling experiments confirm that the electric field serves as the key driver in initiating and guiding this anisotropic melting process. Moreover, electro-thermal stress markedly accelerates the failure, increasing the melting rate from 1.145 to 4.937 nm2/s. By combining experimental observations with theoretical analysis, we establish a complete physical chain in which the synergistic effect of the electric field and the material's intrinsic anisotropy drives external field-induced defect generation and migration, ultimately leading to the anisotropic failure of β-Ga2O3. This work not only provides direct evidence for understanding the failure behavior of β-Ga2O3 under extreme operating conditions, but also offers crucial design guidance for developing highly reliable high-voltage power devices.
- 9 April 2026
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 13 (2)
Electric field-directed anisotropic failure of β -Ga2O3
As one of the critical materials for ultra-high-voltage power devices, β-gallium oxide (β-Ga2O3) faces significant reliability challenges. Under the coupled effects of repeated electrical stress and high-temperature thermal fields, the stability of this material directly determines the reliability of power devices under extreme service conditions. However, to date, atomic-scale real-time observations and mechanistic explanations of the failure process of this material under coupled electro-thermal fields remain lacking. In this study, using in situ transmission electron microscopy (in situ TEM) under coupled thermal-electrical field (500 °C and 1 V bias), we directly observed the anisotropic failure of β-Ga2O3 along low-index planes such as (200). Controlled decoupling experiments confirm that the electric field serves as the key driver in initiating and guiding this anisotropic melting process. Moreover, electro-thermal stress markedly accelerates the failure, increasing the melting rate from 1.145 to 4.937 nm2/s. By combining experimental observations with theoretical analysis, we establish a complete physical chain in which the synergistic effect of the electric field and the material's intrinsic anisotropy drives external field-induced defect generation and migration, ultimately leading to the anisotropic failure of β-Ga2O3. This work not only provides direct evidence for understanding the failure behavior of β-Ga2O3 under extreme operating conditions, but also offers crucial design guidance for developing highly reliable high-voltage power devices.
- 30 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (13)
Atomic-scale in situ TEM investigation of electron beam-induced repair of multiple defects in α -Ga2O3 heterogeneous epitaxial single-crystal films
In the process of epitaxial growth of α-Ga2O3, high density dislocations influence the quality of materials and the performance of devices. In this work, the effects of electron beam irradiation in transmission electron microscope (TEM) on different kinds of defects in α-Ga2O3 were studied. For dislocations, in situ dark field images based on different diffraction vectors and high-resolution TEM images both indicate that after electron beam irradiation (2500 e/Å2s), the repair phenomenon of dislocations with a Burgers vector of 1/3 ⟨112¯3⟩ and 1/3 ⟨11¯00⟩ is observed. With respect to larger size defects, the nano pit (8 × 5 nm2)was repaired to a large extent along (101¯4) after irradiation by an electron beam of 2500 e/Å2s for 39 min. Under electron beam irradiation with the same intensity for 42 min, the nanopore (10 × 9 nm2) was partially repaired along (0006) due to the more severe damage. This discovery provides a method to reduce the defects in two-dimensional α-Ga2O3, which is conducive to the further understanding of the properties of two-dimensional α-Ga2O3 and the development of a variety of devices based on it. At the same time, the potential impact of electron beam irradiation needs to be considered in the process of device manufacturing and the reliability of devices in space. On the contrary, this work also provides positive guidance for defect repair in other semiconductor materials that may be sensitive to electron beam irradiation.
- 30 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (13)
Atomic-scale in situ TEM investigation of electron beam-induced repair of multiple defects in α -Ga2O3 heterogeneous epitaxial single-crystal films
In the process of epitaxial growth of α-Ga2O3, high density dislocations influence the quality of materials and the performance of devices. In this work, the effects of electron beam irradiation in transmission electron microscope (TEM) on different kinds of defects in α-Ga2O3 were studied. For dislocations, in situ dark field images based on different diffraction vectors and high-resolution TEM images both indicate that after electron beam irradiation (2500 e/Å2s), the repair phenomenon of dislocations with a Burgers vector of 1/3 ⟨112¯3⟩ and 1/3 ⟨11¯00⟩ is observed. With respect to larger size defects, the nano pit (8 × 5 nm2)was repaired to a large extent along (101¯4) after irradiation by an electron beam of 2500 e/Å2s for 39 min. Under electron beam irradiation with the same intensity for 42 min, the nanopore (10 × 9 nm2) was partially repaired along (0006) due to the more severe damage. This discovery provides a method to reduce the defects in two-dimensional α-Ga2O3, which is conducive to the further understanding of the properties of two-dimensional α-Ga2O3 and the development of a variety of devices based on it. At the same time, the potential impact of electron beam irradiation needs to be considered in the process of device manufacturing and the reliability of devices in space. On the contrary, this work also provides positive guidance for defect repair in other semiconductor materials that may be sensitive to electron beam irradiation.
- 15 September 2025
- Published by IOP Publishing in Chinese Physics B
- Vol. 35 (5)
A novel stack-HfO2 top-gate structure for improving the performance of network carbon nanotube transistor
Carbon nanotubes (CNTs) are regarded as a powerful contender to replace Si transistors after Moore's Law due to their advantages such as quasi-ballistic transport, high carrier mobility, and low power consumption. In the traditional CNT preparation process, CNTs are deposited on SiO2 substrate and then the gate dielectric is deposited. In this structure, pinholes will appear between CNTs and dielectric layer, which will affect the gate-control and increase the gate leakage current. Therefore, in this paper, we designed a new stack-HfO2 top-gate (STG) network CNTFET. By filling the pinholes between CNTs and dielectric layer, the contact interface condition is improved, reducing the subthreshold swing and improving I on/I off of the device. Meanwhile, through first-principles calculations, compared with the conventional structure, the interface charge transfer value of the CNT/HfO2 interface for STG is about 5 times smaller than that of CNT/SiO2 interface. Specifically, the mobility and SS, and I on/I off of the STG structure are 130 cm2/V·s, 156 mV/dec, and 107, respectively. Taking into account the above advantages, the proposed STG structure has reference value for improving the performance of CNTFET.
- 15 September 2025
- Published by IOP Publishing in Chinese Physics B
- Vol. 35 (5)
A novel stack-HfO2 top-gate structure for improving the performance of network carbon nanotube transistor
Carbon nanotubes (CNTs) are regarded as a powerful contender to replace Si transistors after Moore's Law due to their advantages such as quasi-ballistic transport, high carrier mobility, and low power consumption. In the traditional CNT preparation process, CNTs are deposited on SiO2 substrate and then the gate dielectric is deposited. In this structure, pinholes will appear between CNTs and dielectric layer, which will affect the gate-control and increase the gate leakage current. Therefore, in this paper, we designed a new stack-HfO2 top-gate (STG) network CNTFET. By filling the pinholes between CNTs and dielectric layer, the contact interface condition is improved, reducing the subthreshold swing and improving I on/I off of the device. Meanwhile, through first-principles calculations, compared with the conventional structure, the interface charge transfer value of the CNT/HfO2 interface for STG is about 5 times smaller than that of CNT/SiO2 interface. Specifically, the mobility and SS, and I on/I off of the STG structure are 130 cm2/V·s, 156 mV/dec, and 107, respectively. Taking into account the above advantages, the proposed STG structure has reference value for improving the performance of CNTFET.
- 15 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (11)
Trap-suppressed channel temperature measurement and thermal resistance characterization model for GaN HEMTs
This study proposes a hybrid ultraviolet (UV) electrical characterization method for the precise evaluation of channel temperature (Tch) and thermal resistance (Rth) in gallium nitride-based high electron mobility transistors. In terms of experimental design, by employing UV irradiation to suppress the influence of surface trap effects, the temperature-dependent variation of drain current (Id) is ensured to primarily reflect self-heating phenomena. Based on this approach, high-accuracy of thermal resistance extraction was obtained. Furthermore, in terms of data processing, this work optimizes the conventional Rth calculation equation, demonstrating significantly high consistency between computational results and experimental data. A quantitative relationship between Tch and power dissipation (Pd) was derived, enabling the acquisition of continuous temperature values and Rth characteristics under various bias conditions. This research provides more reliable theoretical foundations and experimental methodologies for thermal management design and performance optimization of such devices.
- 15 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (11)
Trap-suppressed channel temperature measurement and thermal resistance characterization model for GaN HEMTs
This study proposes a hybrid ultraviolet (UV) electrical characterization method for the precise evaluation of channel temperature (Tch) and thermal resistance (Rth) in gallium nitride-based high electron mobility transistors. In terms of experimental design, by employing UV irradiation to suppress the influence of surface trap effects, the temperature-dependent variation of drain current (Id) is ensured to primarily reflect self-heating phenomena. Based on this approach, high-accuracy of thermal resistance extraction was obtained. Furthermore, in terms of data processing, this work optimizes the conventional Rth calculation equation, demonstrating significantly high consistency between computational results and experimental data. A quantitative relationship between Tch and power dissipation (Pd) was derived, enabling the acquisition of continuous temperature values and Rth characteristics under various bias conditions. This research provides more reliable theoretical foundations and experimental methodologies for thermal management design and performance optimization of such devices.
- Open Access
Buried SWCNTs Interlayer Promotes Hole Extraction and Stability in Inverted CsPbI2.85Br0.15 Perovskite Solar Cells
Inverted (p-i-n) CsPbIxBr3−x (x = 0~3) perovskite solar cells (PSCs) are of growing interest due to their excellent thermal stability and optoelectronic performance. However, they suffer from severe energy level mismatch and significant interfacial energy losses at the bottom hole transport layers (HTLs). Herein, we propose a strategy to simultaneously enhance the crystallinity of CsPbI2.85Br0.15 and facilitate hole extraction at the HTL/CsPbI2.85Br0.15 interface by incorporating semiconducting single-walled carbon nanotubes (SWCNTs) onto [2-(3,6-dimethoxy-9H-carbazol-9-yl)ethyl] phosphonic acid (MeO-2PACz) HTL. The unique electrical properties of SWCNTs enable the MeO-2PACz/SWCNT HTL to achieve high conductivity, optimal energy level alignment, and an adaptable surface. Consequently, the defect density is reduced, hole extraction is accelerated, and interfacial charge recombination is effectively suppressed. As a result, these synergistic benefits boost the power conversion efficiency (PCE) from 15.74% to 18.78%. Moreover, unencapsulated devices retained 92.35% of their initial PCE after 150 h of storage in ambient air and 89.03% after accelerated aging at 85 °C for 10 h. These findings highlight the strong potential of SWCNTs as an effective interlayer for inverted CsPbI2.85Br0.15 PSCs and provide a promising strategy for designing high-performance HTLs by integrating SWCNTs with self-assembled monolayers (SAMs).
Open AccessBuried SWCNTs Interlayer Promotes Hole Extraction and Stability in Inverted CsPbI2.85Br0.15 Perovskite Solar Cells
Inverted (p-i-n) CsPbIxBr3−x (x = 0~3) perovskite solar cells (PSCs) are of growing interest due to their excellent thermal stability and optoelectronic performance. However, they suffer from severe energy level mismatch and significant interfacial energy losses at the bottom hole transport layers (HTLs). Herein, we propose a strategy to simultaneously enhance the crystallinity of CsPbI2.85Br0.15 and facilitate hole extraction at the HTL/CsPbI2.85Br0.15 interface by incorporating semiconducting single-walled carbon nanotubes (SWCNTs) onto [2-(3,6-dimethoxy-9H-carbazol-9-yl)ethyl] phosphonic acid (MeO-2PACz) HTL. The unique electrical properties of SWCNTs enable the MeO-2PACz/SWCNT HTL to achieve high conductivity, optimal energy level alignment, and an adaptable surface. Consequently, the defect density is reduced, hole extraction is accelerated, and interfacial charge recombination is effectively suppressed. As a result, these synergistic benefits boost the power conversion efficiency (PCE) from 15.74% to 18.78%. Moreover, unencapsulated devices retained 92.35% of their initial PCE after 150 h of storage in ambient air and 89.03% after accelerated aging at 85 °C for 10 h. These findings highlight the strong potential of SWCNTs as an effective interlayer for inverted CsPbI2.85Br0.15 PSCs and provide a promising strategy for designing high-performance HTLs by integrating SWCNTs with self-assembled monolayers (SAMs).
- 23 June 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (7) , 075020
Tunable negative and positive photoresponses base on s-SWCNT/Ga2O3 MSM solar-blind UV photodetector
Tunable photodetectors have shown great applications in visual signal processing, optoelectronic logic circuits, and memory systems. Nevertheless, deep ultraviolet (DUV) tunable photodetectors still face many challenges such as power consumption, integration and photoelectric performance. This work presents a structural innovation by constructing heterostructures between gallium oxide (Ga2O3) and semiconducting single-wall carbon nanotubes (s-SWCNTs) with varying densities, achieving a tunable photoconductive phenomenon in the DUV area. Both positive and negative photoconductivity (PPC and NPC) exhibit excellent performance under a low bias of 200 mV. Notably, the NPC-effect device achieves a current variation rate of 2.6 × 102, which indicates the potential for advanced optoelectronic applications. The emergence of the NPC photoconductivity can be attributed to the transfer of photogenerated electrons from the Ga2O3 absorption layer to the conductive layer of s-SWCNTs under the built-in electric field. This work demonstrates a promising strategy for developing Ga2O3-based optoelectronic devices with tunable performance.
- 23 June 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (7) , 075020
Tunable negative and positive photoresponses base on s-SWCNT/Ga2O3 MSM solar-blind UV photodetector
Tunable photodetectors have shown great applications in visual signal processing, optoelectronic logic circuits, and memory systems. Nevertheless, deep ultraviolet (DUV) tunable photodetectors still face many challenges such as power consumption, integration and photoelectric performance. This work presents a structural innovation by constructing heterostructures between gallium oxide (Ga2O3) and semiconducting single-wall carbon nanotubes (s-SWCNTs) with varying densities, achieving a tunable photoconductive phenomenon in the DUV area. Both positive and negative photoconductivity (PPC and NPC) exhibit excellent performance under a low bias of 200 mV. Notably, the NPC-effect device achieves a current variation rate of 2.6 × 102, which indicates the potential for advanced optoelectronic applications. The emergence of the NPC photoconductivity can be attributed to the transfer of photogenerated electrons from the Ga2O3 absorption layer to the conductive layer of s-SWCNTs under the built-in electric field. This work demonstrates a promising strategy for developing Ga2O3-based optoelectronic devices with tunable performance.