Stephen M. Walley
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Stephen M. Walley has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- John E. Field
University of Cambridge
9 shared publications Christopher H. Braithwaite
Ray Dolby Centre, Cavendish Laboratory, Department of Physics, University of Cambridge
3 shared publicationsD. M. Williamson
SMF Fracture and Shock Physics Group, The Cavendish Laboratory
3 shared publicationsDavid M. Williamson
PCS Fracture and Shock Physics Group, Cavendish Laboratory University of Cambridge J. J. Thomson Avenue Cambridge CB3 0HE UK
3 shared publicationsJ.E. Field
Fracture and Shock Physics Group, Cavendish Laboratory, J.J. Thomson Avenue, Cambridge CB3 0HE, UK
3 shared publications- Nicholas E. Taylor
Cavendish Laboratory , JJ Thomson Avenue, Cambridge CB3 0HE, United Kingdom
3 shared publications
Latest Publications
- Open Access
- 31 August 2026
- Published by Taylor & Francis in Tribology Transactions
- Vol. 69 (6) , 1448-1456
Why Do Sand Grains Glow When They Break During Erosive Impact: An Explanation of the Kopp–Etchells Effect
Explosions from unknown causes rumble through the cool nights while above drifts the Milky Way, punctuated by more shooting stars than one can remember. The Afghanistan nights will grant a wish to ...
- 31 August 2026
- Published by Taylor & Francis in Tribology Transactions
- Vol. 69 (6) , 1448-1456
Open AccessWhy Do Sand Grains Glow When They Break During Erosive Impact: An Explanation of the Kopp–Etchells Effect
Explosions from unknown causes rumble through the cool nights while above drifts the Milky Way, punctuated by more shooting stars than one can remember. The Afghanistan nights will grant a wish to ...
- Open Access
- 12 March 2025
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 11 (3) , 284-337
The High-Rate Mechanical Properties of Wood Mostly Obtained Using the Kolsky Bar: A Review
This review starts by briefly outlining the history of the study of the response of wood first to impact and second to blast. Due to its importance in the construction of naval ships, wood was one of the first substances to have the velocity dependence of its resistance to terminal ballistic impact quantified. This was achieved in England and France early in the nineteenth century. Techniques for measuring the high-rate mechanical properties of wood were developed around the start of the twentieth century. These mostly involved drop-weight and pendulum machines to quantify the dynamic fracture toughness of timbers of commercial and military importance. These studies were mostly performed in the United States by the US Forest Service with peaks in activity during the two World Wars and again in the 1950s and 1960s due to fears of the bombardment of American cities by Soviet nuclear missiles. It was not until 1977 that the first high-rate compression stress–strain curves of wood were obtained using the Kolsky bar, despite this device having been developed in Britain during World War 2 and reported in the open literature in 1949. It took until the mid-1990s and the desire to use wood to cushion the drop-impact of vessels used to transport nuclear waste that Kolsky bar studies of wood began in earnest in Britain, the Czech Republic and Russia. Even so, to date fewer than 100 such studies have been published compared to nearly 5,000 for metals. This review outlines the effects of anisotropy, stress state, multiple repeat loading, moisture content, temperature, and density on the high-rate properties of a wide range of woods determined using the Kolsky bar. Also included are the very small number of 1D shock and Taylor impact studies that have been performed. The paper ends with suggestions for what needs doing in the future.
- 12 March 2025
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 11 (3) , 284-337
Open AccessThe High-Rate Mechanical Properties of Wood Mostly Obtained Using the Kolsky Bar: A Review
This review starts by briefly outlining the history of the study of the response of wood first to impact and second to blast. Due to its importance in the construction of naval ships, wood was one of the first substances to have the velocity dependence of its resistance to terminal ballistic impact quantified. This was achieved in England and France early in the nineteenth century. Techniques for measuring the high-rate mechanical properties of wood were developed around the start of the twentieth century. These mostly involved drop-weight and pendulum machines to quantify the dynamic fracture toughness of timbers of commercial and military importance. These studies were mostly performed in the United States by the US Forest Service with peaks in activity during the two World Wars and again in the 1950s and 1960s due to fears of the bombardment of American cities by Soviet nuclear missiles. It was not until 1977 that the first high-rate compression stress–strain curves of wood were obtained using the Kolsky bar, despite this device having been developed in Britain during World War 2 and reported in the open literature in 1949. It took until the mid-1990s and the desire to use wood to cushion the drop-impact of vessels used to transport nuclear waste that Kolsky bar studies of wood began in earnest in Britain, the Czech Republic and Russia. Even so, to date fewer than 100 such studies have been published compared to nearly 5,000 for metals. This review outlines the effects of anisotropy, stress state, multiple repeat loading, moisture content, temperature, and density on the high-rate properties of a wide range of woods determined using the Kolsky bar. Also included are the very small number of 1D shock and Taylor impact studies that have been performed. The paper ends with suggestions for what needs doing in the future.
- 26 January 2023
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 9 (1) , 128-130
DYMAT Journal (1994–1995): A Precursor to Journal of Dynamic Behavior of Materials?
- 26 January 2023
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 9 (1) , 128-130
DYMAT Journal (1994–1995): A Precursor to Journal of Dynamic Behavior of Materials?
- Open Access
Is Wood a Material? Taking the Size Effect Seriously
This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.
Open AccessIs Wood a Material? Taking the Size Effect Seriously
This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.
- Open Access
- 24 June 2022
- Published by MDPI AG in Preprints.org
Is Wood a Material?
This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.
- 24 June 2022
- Published by MDPI AG in Preprints.org
Open AccessIs Wood a Material?
This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.
- Open Access
- 15 February 2022
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 8 (2) , 178-213
Measuring the Effect of Strain Rate on Deformation and Damage in Fibre-Reinforced Composites: A Review
This review aims to assess publications relevant to understanding the rate-dependent dynamic behaviour of glass- and carbon-fibre reinforced polymer composites (FRPs). FRPs are complex structures composed of fibres embedded in a polymer matrix, making them highly anisotropic. Their properties depend on their constituent materials as well as micro-, meso- and macro-scale structure. Deformation proceeds via a variety of damage mechanisms which degrade them, and failure can occur by one or more different processes. The damage and failure mechanisms may exhibit complex and unpredictable rate-dependence, with certain phenomena only observable under specific loading conditions or geometries. This review focusses on experimental methods for measuring the rate-dependent deformation of fibre composites: it considers high-stain-rate testing of both specimens of ‘simple’ geometry as well as more complex loadings such as joints, ballistic impact and underwater blast. The effects of strain rate on damage and energy-based processes are also considered, and several scenarios identified where strength and toughness may substantially decrease with an increase in strain rate.
- 15 February 2022
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 8 (2) , 178-213
Open AccessMeasuring the Effect of Strain Rate on Deformation and Damage in Fibre-Reinforced Composites: A Review
This review aims to assess publications relevant to understanding the rate-dependent dynamic behaviour of glass- and carbon-fibre reinforced polymer composites (FRPs). FRPs are complex structures composed of fibres embedded in a polymer matrix, making them highly anisotropic. Their properties depend on their constituent materials as well as micro-, meso- and macro-scale structure. Deformation proceeds via a variety of damage mechanisms which degrade them, and failure can occur by one or more different processes. The damage and failure mechanisms may exhibit complex and unpredictable rate-dependence, with certain phenomena only observable under specific loading conditions or geometries. This review focusses on experimental methods for measuring the rate-dependent deformation of fibre composites: it considers high-stain-rate testing of both specimens of ‘simple’ geometry as well as more complex loadings such as joints, ballistic impact and underwater blast. The effects of strain rate on damage and energy-based processes are also considered, and several scenarios identified where strength and toughness may substantially decrease with an increase in strain rate.
- Open Access
- 16 November 2021
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 8 (2) , 162-177
Vibration-Induced Heating of Energetic Materials: A Review
The transport of energetic materials—whether by truck over rough terrain, or attached to the undercarriage of a high-performance jet aircraft—carries a certain level of inherent risk as the repeatedly applied stresses from vibration may lead to heating, mechanical degradation, and potentially even the triggering of an ignition event. Increasing knowledge of the underlying physics which control ignition is allowing us to better understand, and thus reduce, the risk of a catastrophic event occurring. The Apollo and Space Shuttle programmes provided motivation for research into the topic in the 1960s and 1970s, and some recent studies have focussed on the grain-scale physics of ignition. However, much of the useful insight has arisen from work with other primary applications in mind. Therefore, this review aims to bring together literature from several fields, with the intention of better understanding vibration-induced heating (VIH) phenomena in energetic materials. Sensitivity, VIH in viscoelastic polymers and inert composites, and a technique known as vibrothermography which uses VIH to detect cracks, are all considered where relevant read-across can be found. Often being viscoelastic materials and composites with complex rheology, energetic materials subjected to vibrational loading tend to warm up, with potential for even greater temperature rises due to anisotropy-driven localised heating mechanisms. Binders soften as temperature rises, and the chance of damage increases, which may lead to runaway heating and thermal failure (if mechanical failure does not occur first).
- 16 November 2021
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 8 (2) , 162-177
Open AccessVibration-Induced Heating of Energetic Materials: A Review
The transport of energetic materials—whether by truck over rough terrain, or attached to the undercarriage of a high-performance jet aircraft—carries a certain level of inherent risk as the repeatedly applied stresses from vibration may lead to heating, mechanical degradation, and potentially even the triggering of an ignition event. Increasing knowledge of the underlying physics which control ignition is allowing us to better understand, and thus reduce, the risk of a catastrophic event occurring. The Apollo and Space Shuttle programmes provided motivation for research into the topic in the 1960s and 1970s, and some recent studies have focussed on the grain-scale physics of ignition. However, much of the useful insight has arisen from work with other primary applications in mind. Therefore, this review aims to bring together literature from several fields, with the intention of better understanding vibration-induced heating (VIH) phenomena in energetic materials. Sensitivity, VIH in viscoelastic polymers and inert composites, and a technique known as vibrothermography which uses VIH to detect cracks, are all considered where relevant read-across can be found. Often being viscoelastic materials and composites with complex rheology, energetic materials subjected to vibrational loading tend to warm up, with potential for even greater temperature rises due to anisotropy-driven localised heating mechanisms. Binders soften as temperature rises, and the chance of damage increases, which may lead to runaway heating and thermal failure (if mechanical failure does not occur first).
- Open Access
- 15 April 2020
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 6 (3) , 278-286
The Effect of Temperature Gradients on Elastic Wave Propagation in Split Hopkinson Pressure Bars
If it is desired to obtain high rate mechanical data of materials at non-ambient temperatures using the split Hopkinson (Kolsky) bar technique, it is necessary either to consider what effect a temperature gradient has on the propagation of elastic waves along a metallic rod or to design a mechanism that minimises the exposure of the Hopkinson bars to heating or cooling. Two main mechanical systems have been devised: the first where the bars are brought into contact with the specimen a short time (less than one second) before the specimen is dynamically loaded; the second where the specimen is moved into position just before it is dynamically loaded. As these mechanisms are complex to design and build, many researchers choose the simpler option of heating (or cooling) the ends of the bars as well as the specimen. This review summarises issues that should be considered if this option is taken.
- 15 April 2020
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 6 (3) , 278-286
Open AccessThe Effect of Temperature Gradients on Elastic Wave Propagation in Split Hopkinson Pressure Bars
If it is desired to obtain high rate mechanical data of materials at non-ambient temperatures using the split Hopkinson (Kolsky) bar technique, it is necessary either to consider what effect a temperature gradient has on the propagation of elastic waves along a metallic rod or to design a mechanism that minimises the exposure of the Hopkinson bars to heating or cooling. Two main mechanical systems have been devised: the first where the bars are brought into contact with the specimen a short time (less than one second) before the specimen is dynamically loaded; the second where the specimen is moved into position just before it is dynamically loaded. As these mechanisms are complex to design and build, many researchers choose the simpler option of heating (or cooling) the ends of the bars as well as the specimen. This review summarises issues that should be considered if this option is taken.
- Open Access
- 24 February 2020
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 6 (2) , 113-158
Highways and Byways in the History of High Rate Mechanical Testing
Up until the Industrial Revolution, the dynamic mechanical properties of materials were only of importance in warfare, particularly after the powder-driven gun was invented. With the invention of the steam engine, the explosion of steam boilers (which is similar to the explosion of cannon) became a concern. When railways began to be built, the lack of knowledge of the dynamic properties of the iron alloys used in rails and railway bridges was understood to be a problem, but no way of measuring them was devised until the end of the nineteenth century. Ingenious mechanical (and later electromechanical) methods of recording signals onto rotating drums or moving smoked glass plates began to be developed from the middle of the nineteenth century onwards. Optical/photographic methods of recording information from dynamic experiments date from the 1890s. The rod-on-anvil technique (later named after Taylor) was developed in France at the beginning of the twentieth century but not mathematically analysed until the 1940s. The Hopkinson pressure bar was invented just before the start of the First World War and found to be useful in improving British artillery shells. It was then forgotten about until the Second World War when a two-bar version was developed for measuring the dynamic properties of soft materials such as explosives and polyethylene. As the story of high rate mechanical testing from about 1950 onwards is quite well known to the high rate testing community, this date is taken as the end point of this article.
- 24 February 2020
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 6 (2) , 113-158
Open AccessHighways and Byways in the History of High Rate Mechanical Testing
Up until the Industrial Revolution, the dynamic mechanical properties of materials were only of importance in warfare, particularly after the powder-driven gun was invented. With the invention of the steam engine, the explosion of steam boilers (which is similar to the explosion of cannon) became a concern. When railways began to be built, the lack of knowledge of the dynamic properties of the iron alloys used in rails and railway bridges was understood to be a problem, but no way of measuring them was devised until the end of the nineteenth century. Ingenious mechanical (and later electromechanical) methods of recording signals onto rotating drums or moving smoked glass plates began to be developed from the middle of the nineteenth century onwards. Optical/photographic methods of recording information from dynamic experiments date from the 1890s. The rod-on-anvil technique (later named after Taylor) was developed in France at the beginning of the twentieth century but not mathematically analysed until the 1940s. The Hopkinson pressure bar was invented just before the start of the First World War and found to be useful in improving British artillery shells. It was then forgotten about until the Second World War when a two-bar version was developed for measuring the dynamic properties of soft materials such as explosives and polyethylene. As the story of high rate mechanical testing from about 1950 onwards is quite well known to the high rate testing community, this date is taken as the end point of this article.
- 19 December 2019
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 45 (1) , 53-76
An Assessment of Printing Methods for Producing Two‐Dimensional Lead‐Free Functional Pyrotechnic Delay‐Lines for Mining Applications
Shock‐tube detonators, used in the mining industry to initiate charges of blasting explosives, often contain pyrotechnic delay‐lines for controlling the sequence of blasts. Traditionally, delay‐lines consist of pyrotechnic compounds of toxic metals such as lead which are pressed into the metallic tubing. Since lead is well‐known to be a hazard both to people and the environment, lead‐free alternatives were investigated to create a delay‐line composition. Further, to create delay‐lines cheaply and reproducibly, a composition was developed that could be printed onto a substrate. Screen printing was investigated for this purpose. The pyrotechnic ink that we developed consists of two inert inks (a fuel and an oxidiser) so that it can be stored and transported safely and conveniently without being classified as an energetic. After being transported to its destination, the two inks can be mixed to form an energetic (wet) ink, printed, and used as a delay‐line when dry. A silicon‐bismuth trioxide composition bonded together using nitrocellulose was found to be a suitable ink for screen printing. The burning rate was measured as 52±7 mm s−1 for a thickness of 100 μm. This thickness reduces the raw delay‐line material by over 90 % compared to traditional 3D delay‐lines. The target burning rate was 24 mm/s, but the measured rate is sufficiently close to this that changes in geometry could meet this requirement. The critical thickness for a self‐sustainable burn was measured as 40±5 μm. The thermal output and viscosity of the ink were determined as functions of the particle size. The viscosity of the ink was determined as 7.04±0.05 Pa s, which is suitable for screen printing. Milling was used to reduce the particle size below 1 μm. Ignition of the printed delay‐line using shock tubing was achieved through overprinting with a shock‐sensitive ink. The burning rate of a delay‐line is one of its most defining properties when used in mining applications. Thus the effect on the delay‐line's burning rate of the pyrotechnic composition printed thickness, and the ink solvent was investigated. We found that the burning rate could be modified by changing the silicon content in the pyrotechnic, and to some extent, by adding aluminum. Adding a third, slowly evaporating solvent, to the ink vehicle was found to reduce the critical thickness to less than 40 μm, decrease the burning rate to 46±7 mm s−1, and enhance the ink's flow properties. We found that the width of printed lines did not affect the burning rate for widths between 1–5 mm. This is an interesting result and could be used to determine the most cost‐effective shape to produce printed delay‐lines. Ignition of the printed delay‐line using shock tubing was achieved through overprinting with a shock‐sensitive ink.
- 19 December 2019
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 45 (1) , 53-76
An Assessment of Printing Methods for Producing Two‐Dimensional Lead‐Free Functional Pyrotechnic Delay‐Lines for Mining Applications
Shock‐tube detonators, used in the mining industry to initiate charges of blasting explosives, often contain pyrotechnic delay‐lines for controlling the sequence of blasts. Traditionally, delay‐lines consist of pyrotechnic compounds of toxic metals such as lead which are pressed into the metallic tubing. Since lead is well‐known to be a hazard both to people and the environment, lead‐free alternatives were investigated to create a delay‐line composition. Further, to create delay‐lines cheaply and reproducibly, a composition was developed that could be printed onto a substrate. Screen printing was investigated for this purpose. The pyrotechnic ink that we developed consists of two inert inks (a fuel and an oxidiser) so that it can be stored and transported safely and conveniently without being classified as an energetic. After being transported to its destination, the two inks can be mixed to form an energetic (wet) ink, printed, and used as a delay‐line when dry. A silicon‐bismuth trioxide composition bonded together using nitrocellulose was found to be a suitable ink for screen printing. The burning rate was measured as 52±7 mm s−1 for a thickness of 100 μm. This thickness reduces the raw delay‐line material by over 90 % compared to traditional 3D delay‐lines. The target burning rate was 24 mm/s, but the measured rate is sufficiently close to this that changes in geometry could meet this requirement. The critical thickness for a self‐sustainable burn was measured as 40±5 μm. The thermal output and viscosity of the ink were determined as functions of the particle size. The viscosity of the ink was determined as 7.04±0.05 Pa s, which is suitable for screen printing. Milling was used to reduce the particle size below 1 μm. Ignition of the printed delay‐line using shock tubing was achieved through overprinting with a shock‐sensitive ink. The burning rate of a delay‐line is one of its most defining properties when used in mining applications. Thus the effect on the delay‐line's burning rate of the pyrotechnic composition printed thickness, and the ink solvent was investigated. We found that the burning rate could be modified by changing the silicon content in the pyrotechnic, and to some extent, by adding aluminum. Adding a third, slowly evaporating solvent, to the ink vehicle was found to reduce the critical thickness to less than 40 μm, decrease the burning rate to 46±7 mm s−1, and enhance the ink's flow properties. We found that the width of printed lines did not affect the burning rate for widths between 1–5 mm. This is an interesting result and could be used to determine the most cost‐effective shape to produce printed delay‐lines. Ignition of the printed delay‐line using shock tubing was achieved through overprinting with a shock‐sensitive ink.