Samuel J. Burgess
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Samuel J. Burgess has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
N.E. Evans
Centre for Communications Engineering, School of Electrical and Mechanical Engineering, University of Ulster, Shore Road, Newtownabbey, Co. Antrim BT37 0QB, United Kingdom
3 shared publicationsA.D. Ball
Centre for Communications Engineering, School of Electrical and Mechanical Engineering, University of Ulster, Shore Road, Newtownabbey, Co. Antrim BT37 0QB, United Kingdom
1 shared publication- Ahmed A. Aboushady
Glasgow Caledonian University
1 shared publication G. Trombino
1 shared publication- Ibrahim Abdelsalam
Department of Electrical Engineering, Arab Academy for Science and Technology and Maritime Transport, Cairo, Egypt
1 shared publication - Khaled Hani Ahmed
Department of Electronic and Electrical Engineering, University of Strathclyde, Glasgow, U.K.
1 shared publication
Latest Publications
- 20 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (1) , 399-408
A Design Technique for Optimizing Resonant Coils and the Energy Transfer of Inductive Links
Power transfer efficiency (PTE) is a key performance parameter in development work on resonant inductive power transfer (IPT) systems. Geometrically optimizing the transmitter (Tx) and receiver (Rx) coil pair is a way of improving the IPT system's efficiency. In this article, a new figure-of-merit (FoM) is proposed to find an optimum coil geometry which maximizes the PTE. The employed FoM parameter, called the “strong coupling factor” (P scf ), is defined such that its value indicates how strongly the Tx and Rx coils are linked together. Considering the IPT application and its physical size constraints, a proper selection method for identifying the numerical value of P scf is essential for optimal coil geometry design. This article presents an iterative algorithm to assist in the selection of the most favorable P scf value which provides maximized PTE for the designed optimum coil geometry. Design examples of two nominal IPT systems at frequencies of 415 and 0.1 MHz are used to investigate the design algorithm. Theoretical calculations show the optimum geometry designed for the IPT system operating at 415 MHz, with coupling coefficient (K) of 0.2, can achieve maximum PTE of 85.70%. Measurements presented from a practical Tx/Rx coil pair in the IPT link operating at 0.1 MHz, with K = 0.05, show a PTE of 83.10% against a calculated PTE of 84.11% validating the design process.
- 20 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (1) , 399-408
A Design Technique for Optimizing Resonant Coils and the Energy Transfer of Inductive Links
Power transfer efficiency (PTE) is a key performance parameter in development work on resonant inductive power transfer (IPT) systems. Geometrically optimizing the transmitter (Tx) and receiver (Rx) coil pair is a way of improving the IPT system's efficiency. In this article, a new figure-of-merit (FoM) is proposed to find an optimum coil geometry which maximizes the PTE. The employed FoM parameter, called the “strong coupling factor” (P scf ), is defined such that its value indicates how strongly the Tx and Rx coils are linked together. Considering the IPT application and its physical size constraints, a proper selection method for identifying the numerical value of P scf is essential for optimal coil geometry design. This article presents an iterative algorithm to assist in the selection of the most favorable P scf value which provides maximized PTE for the designed optimum coil geometry. Design examples of two nominal IPT systems at frequencies of 415 and 0.1 MHz are used to investigate the design algorithm. Theoretical calculations show the optimum geometry designed for the IPT system operating at 415 MHz, with coupling coefficient (K) of 0.2, can achieve maximum PTE of 85.70%. Measurements presented from a practical Tx/Rx coil pair in the IPT link operating at 0.1 MHz, with K = 0.05, show a PTE of 83.10% against a calculated PTE of 84.11% validating the design process.
- 14 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 9 (2) , 1328-1338
A New Active Power Controller in Dual Active Bridge DC–DC Converter With a Minimum-Current-Point-Tracking Technique
This paper proposes a new controller for power regulation in dual active bridge (DAB) DC−DC converter based on a new scheme that tracks minimum RMS current to ensure minimum losses. The proposed controller is based on an implementation of perturb and observe (P&O) tracking method that enables minimum current point tracking (MCPT) at any desired level of active power transfer and DC voltage ratio. The P&O is embedded in a closed loop control scheme which simultaneously regulates active power in DAB converter. The non-linear I-V characteristic of DAB presents the basis for this proposed controller and the rationale of using P&O algorithm. The proposed controller does not require complex non-linear converter modelling and is not circuit parameter dependent. Design procedure of the proposed controller is presented, and extensive simulation is carried out using MATLAB/Simulink to validate effectiveness of the proposed MCPT closed loop controller. An experimental prototype also substantiates the results achieved.
- 14 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 9 (2) , 1328-1338
A New Active Power Controller in Dual Active Bridge DC–DC Converter With a Minimum-Current-Point-Tracking Technique
This paper proposes a new controller for power regulation in dual active bridge (DAB) DC−DC converter based on a new scheme that tracks minimum RMS current to ensure minimum losses. The proposed controller is based on an implementation of perturb and observe (P&O) tracking method that enables minimum current point tracking (MCPT) at any desired level of active power transfer and DC voltage ratio. The P&O is embedded in a closed loop control scheme which simultaneously regulates active power in DAB converter. The non-linear I-V characteristic of DAB presents the basis for this proposed controller and the rationale of using P&O algorithm. The proposed controller does not require complex non-linear converter modelling and is not circuit parameter dependent. Design procedure of the proposed controller is presented, and extensive simulation is carried out using MATLAB/Simulink to validate effectiveness of the proposed MCPT closed loop controller. An experimental prototype also substantiates the results achieved.
- 27 September 2007
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 43 (20) , 1063-1065
Head-SAR dependence on spectacle frame shape for operator of 450 MHz personal radio
Power deposition in the head of a user wearing metal-framed spectacles was calculated with a 450 MHz personal radio transmitting in close proximity. Peak tissue SAR in the head depended on lens shape—whether circular half-rim or rectangular—with 70 and 174% increases, respectively, compared to the spectacle-free case. However, localised screening occurred with square frames, with a 40% reduction of peak SAR in the eye closest to the antenna.
- 27 September 2007
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 43 (20) , 1063-1065
Head-SAR dependence on spectacle frame shape for operator of 450 MHz personal radio
Power deposition in the head of a user wearing metal-framed spectacles was calculated with a 450 MHz personal radio transmitting in close proximity. Peak tissue SAR in the head depended on lens shape—whether circular half-rim or rectangular—with 70 and 174% increases, respectively, compared to the spectacle-free case. However, localised screening occurred with square frames, with a 40% reduction of peak SAR in the eye closest to the antenna.
- 1 January 2006
- Published by Institution of Engineering and Technology (IET)
- p. 201-205
A low-cost microstrip UWB pulse generator with integral biphase switching modulation
We report on preliminary results from the development of a low-data rate, low-cost, Ultra-wideband (UWB) pulse generator which uses an RF Step Recovery Diode (SRD) on microstrip board. A circuit employing a single Skyworks CVB1031 SRD part on Rogers RT/Duroid 5870 RF board has been developed using HP Advanced Design System (ADS) software; initial simulation results show that sub nano-second (0.4 - 0.6 ns) monocycle wideband pulses with a repetition period of 2.5 ns (400 MHz) are achievable. While wideband pulse generators using SRD parts have been verified elsewhere [5, 7], the novelty in this work is that a six-finger, interdigitated Lange Coupler, employing an LC tank switching technique previously demonstrated at integrated circuit (IC) level [8], has been added to the pulse generator to yield a bi-phase pulse modulation technique. Pilot findings show a high degree of symmetry between the bi-phase output pulses, demonstrating how an RF pulse generator, designed with low-cost microstrip board and SMD techniques, has the potential to be used as a cost-effective pulse modulator solution in the physical layer of a wideband communication system.
- 1 January 2006
- Published by Institution of Engineering and Technology (IET)
- p. 201-205
A low-cost microstrip UWB pulse generator with integral biphase switching modulation
We report on preliminary results from the development of a low-data rate, low-cost, Ultra-wideband (UWB) pulse generator which uses an RF Step Recovery Diode (SRD) on microstrip board. A circuit employing a single Skyworks CVB1031 SRD part on Rogers RT/Duroid 5870 RF board has been developed using HP Advanced Design System (ADS) software; initial simulation results show that sub nano-second (0.4 - 0.6 ns) monocycle wideband pulses with a repetition period of 2.5 ns (400 MHz) are achievable. While wideband pulse generators using SRD parts have been verified elsewhere [5, 7], the novelty in this work is that a six-finger, interdigitated Lange Coupler, employing an LC tank switching technique previously demonstrated at integrated circuit (IC) level [8], has been added to the pulse generator to yield a bi-phase pulse modulation technique. Pilot findings show a high degree of symmetry between the bi-phase output pulses, demonstrating how an RF pulse generator, designed with low-cost microstrip board and SMD techniques, has the potential to be used as a cost-effective pulse modulator solution in the physical layer of a wideband communication system.
- 1 April 1999
- Published by Institution of Engineering and Technology (IET) in Electronics & Communication Engineering Journal
- Vol. 11 (2) , 95-104
Short-haul communications using NVIS HF radio
In geographical regions poorly served by land-lines or line-of-sight repeaters, high-frequency (HF) radio can still provide a low-cost alternative to satellite links. In particular, the near vertical incidence sky-wave (NVIS) propagation mode gives omnidirectional coverage from a central site; 300 km ranges are possible and the technique has an inherent ability to fill in `blind spots' lying in hilly ground. Normal voice and data services may be readily established. This paper introduces NVIS radio, discusses some of its roles to date and examines the hardware required for basic link implementation; emphasis is placed on antenna design and selection. Channel availability and fading characteristics (depth and frequency) gathered from a 6793 kHz oblique sounder over the 1997/8 winter-summer transition are included to illustrate the potential of the technique for non-real-time remote monitoring applications.
- 1 April 1999
- Published by Institution of Engineering and Technology (IET) in Electronics & Communication Engineering Journal
- Vol. 11 (2) , 95-104
Short-haul communications using NVIS HF radio
In geographical regions poorly served by land-lines or line-of-sight repeaters, high-frequency (HF) radio can still provide a low-cost alternative to satellite links. In particular, the near vertical incidence sky-wave (NVIS) propagation mode gives omnidirectional coverage from a central site; 300 km ranges are possible and the technique has an inherent ability to fill in `blind spots' lying in hilly ground. Normal voice and data services may be readily established. This paper introduces NVIS radio, discusses some of its roles to date and examines the hardware required for basic link implementation; emphasis is placed on antenna design and selection. Channel availability and fading characteristics (depth and frequency) gathered from a 6793 kHz oblique sounder over the 1997/8 winter-summer transition are included to illustrate the potential of the technique for non-real-time remote monitoring applications.
- 1 January 1999
- Published by Institution of Engineering and Technology (IET)
- Vol. 1999, 101-104
Characteristics of a mid-latitude NVIS HF radio channel
This paper reports on the initial findings of measurements taken using a low cost, near vertical incidence skywave (NVIS) single channel sounder. The path investigated is unique in that although it is truly non-line-of-sight, operational results have been documented for coverage just beyond the ground-wave range; in the literature to date a commonly suggested NVIS lower boundary is 80 km. The consistency of the link reflects the potential of the NVIS technique for many practical short- to medium-range data communication scenarios, especially if store-and-forward techniques can be adopted.
- 1 January 1999
- Published by Institution of Engineering and Technology (IET)
- Vol. 1999, 101-104
Characteristics of a mid-latitude NVIS HF radio channel
This paper reports on the initial findings of measurements taken using a low cost, near vertical incidence skywave (NVIS) single channel sounder. The path investigated is unique in that although it is truly non-line-of-sight, operational results have been documented for coverage just beyond the ground-wave range; in the literature to date a commonly suggested NVIS lower boundary is 80 km. The consistency of the link reflects the potential of the NVIS technique for many practical short- to medium-range data communication scenarios, especially if store-and-forward techniques can be adopted.