Hayden Taylor
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hayden Taylor has a total of 137 co-authors. Here are the top co-authors by number of shared publications:
- Joseph Toombs
Department of Mechanical Engineering University of California Berkeley CA 94720 USA
5 shared publications - Chi Chung Li
Univ Calif Berkeley, Dept Mech Engn, Etcheverry Hall 6124,2521 Hearst Ave, Berkeley, CA 94720 USA
4 shared publications Soochan Chung
Department of Mechanical Engineering University of California 6159 Etcheverry Hall Berkeley CA 94720 USA
4 shared publications- Ciprian Iliescu
Bio-Hub Centre of Excellence in Bioengineering, National University of Science and Technology POLITEHNICA Bucharest, 060042 Bucharest, Romania
3 shared publications - Florina Silvia Iliescu
Bio-Hub Centre of Excellence in Bioengineering, National University of Science and Technology POLITEHNICA Bucharest, 060042 Bucharest, Romania
3 shared publications - Hossein Heidari
Institute for Materials Discovery, University College London, London E20 2AE, UK
3 shared publications
Latest Publications
- Open Access
- 27 May 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Enhanced volumetric additive manufacturing via Reversible Addition-Fragmentation Chain Transfer (RAFT) polymerization
Computed Axial Lithography (CAL), a Volumetric Additive Manufacturing (VAM) technology, enables the rapid, full body i.e. not layer-by-layer, fabrication of freeform geometries within seconds through the superposition of projected light patterns. However, as conventional CAL relies on free radical polymerization (FRP), it is an intrinsically exothermic process (ΔT > 60 °C) that can trigger auto-acceleration, so compromising print fidelity and limiting scalability. By regulating polymer chain length during propagation through reversible chain transfer, Reversible Addition–Fragmentation Chain Transfer (RAFT) maintains steady, controlled reaction kinetics and prevents the sharp viscosity increase characteristic of FRP. In this study, we introduce RAFT polymerization into various (meth)acrylate-based systems within CAL to effectively mitigate heat generation and suppress auto-acceleration during photopolymerization. The success of this approach is confirmed by in-situ thermal monitoring and the suppression of thermally induced buoyancy, revealing a substantial reduction in temperature rise compared to FRP. Furthermore, RAFT chemistry enables post-printing functionalization of the printed objects, expanding CAL’s chemical versatility. This study demonstrates that RAFT-mediated CAL allows the fabrication of structures inaccessible via FRP, advancing thermally stable and functionally tunable volumetric additive manufacturing.
- 27 May 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Open AccessEnhanced volumetric additive manufacturing via Reversible Addition-Fragmentation Chain Transfer (RAFT) polymerization
Computed Axial Lithography (CAL), a Volumetric Additive Manufacturing (VAM) technology, enables the rapid, full body i.e. not layer-by-layer, fabrication of freeform geometries within seconds through the superposition of projected light patterns. However, as conventional CAL relies on free radical polymerization (FRP), it is an intrinsically exothermic process (ΔT > 60 °C) that can trigger auto-acceleration, so compromising print fidelity and limiting scalability. By regulating polymer chain length during propagation through reversible chain transfer, Reversible Addition–Fragmentation Chain Transfer (RAFT) maintains steady, controlled reaction kinetics and prevents the sharp viscosity increase characteristic of FRP. In this study, we introduce RAFT polymerization into various (meth)acrylate-based systems within CAL to effectively mitigate heat generation and suppress auto-acceleration during photopolymerization. The success of this approach is confirmed by in-situ thermal monitoring and the suppression of thermally induced buoyancy, revealing a substantial reduction in temperature rise compared to FRP. Furthermore, RAFT chemistry enables post-printing functionalization of the printed objects, expanding CAL’s chemical versatility. This study demonstrates that RAFT-mediated CAL allows the fabrication of structures inaccessible via FRP, advancing thermally stable and functionally tunable volumetric additive manufacturing.
- Open Access
- 21 May 2026
- Published by Elsevier in Acta Astronautica
- Vol. 247, 827-842
Demonstration and analysis of volumetric additive manufacturing via sub-orbital spaceflight testing
- 21 May 2026
- Published by Elsevier in Acta Astronautica
- Vol. 247, 827-842
Open AccessDemonstration and analysis of volumetric additive manufacturing via sub-orbital spaceflight testing
- Open Access
- 23 July 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Enhanced Volumetric Additive Manufacturing via Reversible Addition-Fragmentation Chain Transfer (RAFT) Polymerization
In this study, we introduce Reversible Addition-Fragmentation Chain Transfer (RAFT) polymerization into various (meth)acrylate-based polymer systems to effectively mitigate heat generation and expand the design space of CAL. RAFT also allows for post-printing-functionalization of the printed objects, expanding the potential application scope of CAL. The success of this approach to mitigate auto-acceleration is demonstrated through in-situ thermal monitoring. Computed Axial Lithography (CAL), the most widely adopted Volumetric Additive Manufacturing (VAM) technology, has shown great potential for manufacturing freeform geometries in seconds. In CAL, regions of photopolymer exposed to a threshold light dose level solidify rapidly and simultaneously through the superposition of projected light patterns from multiple angular positions. While free radical polymerization (FRP) has been the primary reaction mechanism enabling CAL’s rapid fabrication, its exothermic effects (ΔT > 60 °C) can trigger auto-acceleration, compromising print fidelity and limiting the scalability of VAM. The fabrication of novel structures that cannot be printed via FRP is enabled by RAFT both via direct VAM processing and post-polymerization.
- 23 July 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessEnhanced Volumetric Additive Manufacturing via Reversible Addition-Fragmentation Chain Transfer (RAFT) Polymerization
In this study, we introduce Reversible Addition-Fragmentation Chain Transfer (RAFT) polymerization into various (meth)acrylate-based polymer systems to effectively mitigate heat generation and expand the design space of CAL. RAFT also allows for post-printing-functionalization of the printed objects, expanding the potential application scope of CAL. The success of this approach to mitigate auto-acceleration is demonstrated through in-situ thermal monitoring. Computed Axial Lithography (CAL), the most widely adopted Volumetric Additive Manufacturing (VAM) technology, has shown great potential for manufacturing freeform geometries in seconds. In CAL, regions of photopolymer exposed to a threshold light dose level solidify rapidly and simultaneously through the superposition of projected light patterns from multiple angular positions. While free radical polymerization (FRP) has been the primary reaction mechanism enabling CAL’s rapid fabrication, its exothermic effects (ΔT > 60 °C) can trigger auto-acceleration, compromising print fidelity and limiting the scalability of VAM. The fabrication of novel structures that cannot be printed via FRP is enabled by RAFT both via direct VAM processing and post-polymerization.
- 13 December 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (26) , 47620
Intensity-coupled multi-beam phase retrieval for holographic volumetric additive manufacturing
Multi-beam holographic projection is a promising yet underexplored avenue for advanced volumetric additive manufacturing (VAM) systems to control image focus in 3D, compensate for aberrations, and overcome resolution anisotropy. Nevertheless, there is currently no formal method to jointly optimize multiple holographic projections for maximum reconstruction fidelity of the printed object. This work introduces an optimization framework to search for the optimal set of projection parameters, namely phase modulation values and amplitudes, for multi-beam holographic lithography. The proposed framework is more general than classical phase retrieval algorithms in the sense that it can simultaneously optimize multiple holographic beams and model the coupled non-linear material response created by co-illumination of the holograms. The framework incorporates efficient methods to evaluate holographic light fields, resample quantities across coordinate grids, and compute the coupled exposure effect. The efficacy of this optimization method is tested for a variety of setup configurations that involve multi-wavelength illumination and time-multiplexed scanning beams. Among all demonstrations, a special test case of holo-tomographic patterning achieved the lowest error with 128 simultaneously optimized holograms, highlighting its potential in high-contrast microscale fabrication. All testing results indicate that a fully coupled optimization offers superior solutions relative to a decoupled optimization approach.
- 13 December 2024
- Published by Optica Publishing Group in Optics Express
- Vol. 32 (26) , 47620
Intensity-coupled multi-beam phase retrieval for holographic volumetric additive manufacturing
Multi-beam holographic projection is a promising yet underexplored avenue for advanced volumetric additive manufacturing (VAM) systems to control image focus in 3D, compensate for aberrations, and overcome resolution anisotropy. Nevertheless, there is currently no formal method to jointly optimize multiple holographic projections for maximum reconstruction fidelity of the printed object. This work introduces an optimization framework to search for the optimal set of projection parameters, namely phase modulation values and amplitudes, for multi-beam holographic lithography. The proposed framework is more general than classical phase retrieval algorithms in the sense that it can simultaneously optimize multiple holographic beams and model the coupled non-linear material response created by co-illumination of the holograms. The framework incorporates efficient methods to evaluate holographic light fields, resample quantities across coordinate grids, and compute the coupled exposure effect. The efficacy of this optimization method is tested for a variety of setup configurations that involve multi-wavelength illumination and time-multiplexed scanning beams. Among all demonstrations, a special test case of holo-tomographic patterning achieved the lowest error with 128 simultaneously optimized holograms, highlighting its potential in high-contrast microscale fabrication. All testing results indicate that a fully coupled optimization offers superior solutions relative to a decoupled optimization approach.
- 30 October 2024
- Published by Springer Nature in Nature
- Vol. 634 (8036) , 1061-1062
Rapid 3D-printing method could be used on space missions
- 30 October 2024
- Published by Springer Nature in Nature
- Vol. 634 (8036) , 1061-1062
Rapid 3D-printing method could be used on space missions
- Top Cited PapersOpen Access
- 21 July 2023
- Published by Springer Nature in Nature Communications
- Vol. 14 (1) , 1-11
Deconvolution volumetric additive manufacturing
Volumetric additive manufacturing techniques are a promising pathway to ultra-rapid light-based 3D fabrication. Their widespread adoption, however, demands significant improvement in print fidelity. Currently, volumetric additive manufacturing prints suffer from systematic undercuring of fine features, making it impossible to print objects containing a wide range of feature sizes, precluding effective adoption in many applications. Here, we uncover the reason for this limitation: light dose spread in the resin due to chemical diffusion and optical blurring, which becomes significant for features ⪅0.5 mm. We develop a model that quantitatively predicts the variation of print time with feature size and demonstrate a deconvolution method to correct for this error. This enables prints previously beyond the capabilities of volumetric additive manufacturing, such as a complex gyroid structure with variable thickness and a fine-toothed gear. These results position volumetric additive manufacturing as a mature 3D printing method, all but eliminating the gap to industry-standard print fidelity.
- 21 July 2023
- Published by Springer Nature in Nature Communications
- Vol. 14 (1) , 1-11
Top Cited PapersOpen AccessDeconvolution volumetric additive manufacturing
Volumetric additive manufacturing techniques are a promising pathway to ultra-rapid light-based 3D fabrication. Their widespread adoption, however, demands significant improvement in print fidelity. Currently, volumetric additive manufacturing prints suffer from systematic undercuring of fine features, making it impossible to print objects containing a wide range of feature sizes, precluding effective adoption in many applications. Here, we uncover the reason for this limitation: light dose spread in the resin due to chemical diffusion and optical blurring, which becomes significant for features ⪅0.5 mm. We develop a model that quantitatively predicts the variation of print time with feature size and demonstrate a deconvolution method to correct for this error. This enables prints previously beyond the capabilities of volumetric additive manufacturing, such as a complex gyroid structure with variable thickness and a fine-toothed gear. These results position volumetric additive manufacturing as a mature 3D printing method, all but eliminating the gap to industry-standard print fidelity.
- Open Access
- 6 July 2023
- Published by Elsevier in Acta Astronautica
- Vol. 211, 474-482
Use of volumetric additive manufacturing as an in-space manufacturing technology
- 6 July 2023
- Published by Elsevier in Acta Astronautica
- Vol. 211, 474-482
Open AccessUse of volumetric additive manufacturing as an in-space manufacturing technology
- Open Access
- 22 April 2023
- Published by Elsevier in Materials & Design
- Vol. 230
Highly compressible concrete: The effect of reinforcement design on concrete’s compressive behavior at high strains
- 22 April 2023
- Published by Elsevier in Materials & Design
- Vol. 230
Open AccessHighly compressible concrete: The effect of reinforcement design on concrete’s compressive behavior at high strains
- 22 February 2023
- Published by Wiley in Macromolecular Rapid Communications
- Vol. 44 (7) , e2200872
Ethyl Cellulose‐Based Thermoreversible Organogel Photoresist for Sedimentation‐Free Volumetric Additive Manufacturing
Liquid photoresists are abundant in the field of light‐based additive manufacturing (AM). However, printing unsupported directly into a vat of material in emerging volumetric AM technologies―typically a benefit due to fewer geometric constraints and less material waste―can be a limitation when printing low‐viscosity liquid monomers and multimaterial constructs due to part drift or sedimentation. With ethyl cellulose (EC), a thermoplastic soluble in organic liquids, a simple three‐component transparent thermoreversible gel photoresist with melting temperature of ≈64 °C is formulated. The physically crosslinked network of the gel leads to storage moduli in the range of 0.1−10 kPa and maximum yield stress of 2.7 kPa for a 10 wt% EC gel photoresist. Nonzero yield stress enables sedimentation‐free tomographic volumetric patterning in low‐viscosity monomer without additional hardware or modification of apparatus. In addition, objects inserted into the print container can be suspended in the gel material which enables overprinting of multimaterial devices without anchors connecting the object to the printing container. Flexural strength is also improved by 100% compared to the neat monomer for a formulation with 7 wt% EC.
- 22 February 2023
- Published by Wiley in Macromolecular Rapid Communications
- Vol. 44 (7) , e2200872
Ethyl Cellulose‐Based Thermoreversible Organogel Photoresist for Sedimentation‐Free Volumetric Additive Manufacturing
Liquid photoresists are abundant in the field of light‐based additive manufacturing (AM). However, printing unsupported directly into a vat of material in emerging volumetric AM technologies―typically a benefit due to fewer geometric constraints and less material waste―can be a limitation when printing low‐viscosity liquid monomers and multimaterial constructs due to part drift or sedimentation. With ethyl cellulose (EC), a thermoplastic soluble in organic liquids, a simple three‐component transparent thermoreversible gel photoresist with melting temperature of ≈64 °C is formulated. The physically crosslinked network of the gel leads to storage moduli in the range of 0.1−10 kPa and maximum yield stress of 2.7 kPa for a 10 wt% EC gel photoresist. Nonzero yield stress enables sedimentation‐free tomographic volumetric patterning in low‐viscosity monomer without additional hardware or modification of apparatus. In addition, objects inserted into the print container can be suspended in the gel material which enables overprinting of multimaterial devices without anchors connecting the object to the printing container. Flexural strength is also improved by 100% compared to the neat monomer for a formulation with 7 wt% EC.
- 2 February 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (3)
A Bioinspired Triple‐Hierarchical Superhydrophobic Surface with Exceptional Robustness to Water Impingement
- 2 February 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (3)
A Bioinspired Triple‐Hierarchical Superhydrophobic Surface with Exceptional Robustness to Water Impingement