Wolfgang Häßler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wolfgang Häßler has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
K. Nenkov
International Laboratory of High Magnetic Fields and Low Temperatures (HMF and LT) 1 , Gajowicka 95, 53-421 Wrocław, Poland
3 shared publicationsAli Bateni
Department of Chemistry, Koç University 1 , Rumelifeneri Yolu, Sariyer, Istanbul, Turkey
2 shared publications- Andrzej Janusz Zaleski
Institute of Low Temperature and Structure Research, Polish Academy of Sciences , 50-422 Wroclaw
2 shared publications - Andrzej Morawski
Institute of High Pressure Physics PAS, Sokolowska 29/37, 01-142 Warsaw, Poland
2 shared publications - Emre Erdem
Faculty of Engineering and Natural Sciences, Sabanci University, Istanbul, Turkey
2 shared publications M. A. Rindfleisch
Hyper Tech Research, Inc. 6 , 539 Industrial Mile Rd, Columbus, Ohio 43228, USA
2 shared publications
Latest Publications
- Open Access
- 1 April 2019
- Published by AIP Publishing in AIP Advances
- Vol. 9 (4) , 045018
High-quality MgB2 nanocrystals synthesized by using modified amorphous nano-boron powders: Study of defect structures and superconductivity properties
Nano sized magnesium diboride (MgB2) samples were synthesized using various high-quality nano-B precursor powders. The microscopic defect structures of MgB2 samples were systematically investigated using X-ray powder diffraction, Raman, resistivity measurements and electron paramagnetic resonance spectroscopy. A significant deviation in the critical temperature Tc was observed due to defects and crystal distortion. The symmetry effect of the latter is also reflected on the vibrational modes in the Raman spectra. Scanning electron microscopy analysis demonstrate uniform and ultrafine morphology for the modified MgB2. Defect center in particular Mg vacancies influence the connectivity and the conductivity properties which are crucial for the superconductivity applications.
- 1 April 2019
- Published by AIP Publishing in AIP Advances
- Vol. 9 (4) , 045018
Open AccessHigh-quality MgB2 nanocrystals synthesized by using modified amorphous nano-boron powders: Study of defect structures and superconductivity properties
Nano sized magnesium diboride (MgB2) samples were synthesized using various high-quality nano-B precursor powders. The microscopic defect structures of MgB2 samples were systematically investigated using X-ray powder diffraction, Raman, resistivity measurements and electron paramagnetic resonance spectroscopy. A significant deviation in the critical temperature Tc was observed due to defects and crystal distortion. The symmetry effect of the latter is also reflected on the vibrational modes in the Raman spectra. Scanning electron microscopy analysis demonstrate uniform and ultrafine morphology for the modified MgB2. Defect center in particular Mg vacancies influence the connectivity and the conductivity properties which are crucial for the superconductivity applications.
- Open Access
The Aerosol Deposition Method: A Modified Aerosol Generation Unit to Improve Coating Quality
Owing to its ability to produce dense thick-films at room temperature directly from a ceramic powder, the Aerosol Deposition Method (AD) possesses a unique feature in ceramics processing. For this technology, the aerosol generation of particles is a decisive part of reliable process control. However, there has only been a small amount of work published addressing this topic. In this work, we compare the aerosolization and deposition behavior of a fluidized bed generator with an aerosol generator with the rotary brush principle. While film properties very much depend on deposition time for the fluidized bed generator, films produced with the brush generator show a constant film profile, and their film thickness correlates with the controllable aerosol concentration and the duration of deposition. This type of aerosol generation may improve the setup towards a more reliable AD process.
Open AccessThe Aerosol Deposition Method: A Modified Aerosol Generation Unit to Improve Coating Quality
Owing to its ability to produce dense thick-films at room temperature directly from a ceramic powder, the Aerosol Deposition Method (AD) possesses a unique feature in ceramics processing. For this technology, the aerosol generation of particles is a decisive part of reliable process control. However, there has only been a small amount of work published addressing this topic. In this work, we compare the aerosolization and deposition behavior of a fluidized bed generator with an aerosol generator with the rotary brush principle. While film properties very much depend on deposition time for the fluidized bed generator, films produced with the brush generator show a constant film profile, and their film thickness correlates with the controllable aerosol concentration and the duration of deposition. This type of aerosol generation may improve the setup towards a more reliable AD process.
- 12 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (4) , 1-4
Magnetic Flux Invasion and Field-Capturing in Pulsed-Field Magnetization for Layered MgB2 Bulk Magnets
The pulsed-field magnetization experiments have been carried out for the layered MgB 2 bulk magnets to clarify the magnetic flux motion during the activation processes. Since MgB 2 is characterized as homogeneous, lightweight, and inexpensive HTS materialin comparison to RE123 compounds (RE = rare earth), the material may have an advantage of possibly uniform magnetic field generation. The values of applied field B a which begin to reach the sample center were responsible for the total sample thickness, reflecting the shielding effect to suppress the flux invasion. As well, the estimation on the ratios of trapped field BT over penetration field B p showed us the reluctant field invasion with increasing sample thickness. The field trapping ratios B T /B p decreased with increasing applied field due to heat generation. In the region over 1.4 T, the drastic flux flow and sudden flux jumps were often observed, which lowered the field-capturing ability. The arriving time which corresponds to the flux increasing speed showed us that the rapid flux invasions which occur in the low-field ranges resulted in the highest field-capturing. This suggests us the possible promotion of field-capturing without significant heat generation.
- 12 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 28 (4) , 1-4
Magnetic Flux Invasion and Field-Capturing in Pulsed-Field Magnetization for Layered MgB2 Bulk Magnets
The pulsed-field magnetization experiments have been carried out for the layered MgB 2 bulk magnets to clarify the magnetic flux motion during the activation processes. Since MgB 2 is characterized as homogeneous, lightweight, and inexpensive HTS materialin comparison to RE123 compounds (RE = rare earth), the material may have an advantage of possibly uniform magnetic field generation. The values of applied field B a which begin to reach the sample center were responsible for the total sample thickness, reflecting the shielding effect to suppress the flux invasion. As well, the estimation on the ratios of trapped field BT over penetration field B p showed us the reluctant field invasion with increasing sample thickness. The field trapping ratios B T /B p decreased with increasing applied field due to heat generation. In the region over 1.4 T, the drastic flux flow and sudden flux jumps were often observed, which lowered the field-capturing ability. The arriving time which corresponds to the flux increasing speed showed us that the rapid flux invasions which occur in the low-field ranges resulted in the highest field-capturing. This suggests us the possible promotion of field-capturing without significant heat generation.
- Open Access
- 15 September 2016
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 120 (11)
Experimental research of high field pinning centers in 2% C doped MgB2 wires at 20 K and 25 K
High field pinning centers in MgB2 doped with 2 at. % carbon under a low and a high hot isostatic pressures have been investigated by transport measurements. The field dependence of the transport critical current density was analyzed within the different pinning mechanisms: surface pinning, point pinning, and pinning due to spatial variation in the Ginzburg-Landau parameter (Δκ pinning). Research indicates that a pressure of 1 GPa allows similar pinning centers to Δκ pinning centers to be obtained. This pinning is very important, because it makes it possible to increase the critical current density in high magnetic fields at 20 K and 25 K. Our results indicate that the δTc and δl pinning mechanisms, which are due to a spatial variation in the critical temperature (Tc) and the mean free path, l, respectively, create dislocations. The high density of dislocations with inhomogeneous distribution in the structure of the superconducting material creates the δl pinning mechanism. The low density of dislocations with inhomogeneous distribution creates the δTc pinning mechanism. Research indicates that the hot isostatic pressure process makes it possible to obtain a high dislocation density with a homogeneous distribution. This allows us to obtain the δTc pinning mechanism in MgB2 wires. In addition, a high pressure increases the crossover field from the single vortex to the small vortex bundle regime (Bsb) and improves the δTc pinning mechanism. Our research has proved that a high pressure significantly increases the crossover field from the small bundle to the thermal regime (Bth), with only a modest decrease in Tc of 1.5 K, decreases the thermal fluctuations, increases the irreversibility magnetic field (Birr) and the upper critical field (Bc2) in the temperature range from 4.2 K to 25 K, and reduces Birr and Bc2 above 25 K.
- 15 September 2016
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 120 (11)
Open AccessExperimental research of high field pinning centers in 2% C doped MgB2 wires at 20 K and 25 K
High field pinning centers in MgB2 doped with 2 at. % carbon under a low and a high hot isostatic pressures have been investigated by transport measurements. The field dependence of the transport critical current density was analyzed within the different pinning mechanisms: surface pinning, point pinning, and pinning due to spatial variation in the Ginzburg-Landau parameter (Δκ pinning). Research indicates that a pressure of 1 GPa allows similar pinning centers to Δκ pinning centers to be obtained. This pinning is very important, because it makes it possible to increase the critical current density in high magnetic fields at 20 K and 25 K. Our results indicate that the δTc and δl pinning mechanisms, which are due to a spatial variation in the critical temperature (Tc) and the mean free path, l, respectively, create dislocations. The high density of dislocations with inhomogeneous distribution in the structure of the superconducting material creates the δl pinning mechanism. The low density of dislocations with inhomogeneous distribution creates the δTc pinning mechanism. Research indicates that the hot isostatic pressure process makes it possible to obtain a high dislocation density with a homogeneous distribution. This allows us to obtain the δTc pinning mechanism in MgB2 wires. In addition, a high pressure increases the crossover field from the single vortex to the small vortex bundle regime (Bsb) and improves the δTc pinning mechanism. Our research has proved that a high pressure significantly increases the crossover field from the small bundle to the thermal regime (Bth), with only a modest decrease in Tc of 1.5 K, decreases the thermal fluctuations, increases the irreversibility magnetic field (Birr) and the upper critical field (Bc2) in the temperature range from 4.2 K to 25 K, and reduces Birr and Bc2 above 25 K.
- 5 May 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (17) , 173908
The critical parameters in in-situ MgB2 wires and tapes with ex-situ MgB2 barrier after hot isostatic pressure, cold drawing, cold rolling and doping
MgB2 precursor wires were prepared using powder in tube technique by Institute of High Pressure PAS in Warsaw. All samples were annealed under isostatic pressure generated by liquid Argon in the range from 0.3 GPa to 1 GPa. In this paper, we show the effects of different processing routes, namely, cold drawing (CD), cold rolling (CR), hot isostatic pressure (HIP) and doping on critical current density (Jc), pinning force (Fp), irreversible magnetic-field (Birr), critical temperature (Tc), n value, and dominant pinning mechanism in MgB2/Fe wires with ex situ MgB2 barrier. The results show that medium pressures (∼0.35 GPa) lead to high Jc in low and medium magnetic fields (0 T – 9 T). On the other hand, higher pressures (∼1 GPa) lead to enhanced Jc in high magnetic fields (above 9 T). Transport measurements show that CD, CR, and HIP have small effects on Birr and Tc, but CD, CR, HIP, and doping enhance Jc and Fp in in situ MgB2 wires with ex situ MgB2 barrier. Transport measurements on in situ undoped MgB2 wire with ex situ MgB2 barrier yield a Jc of about 100 A/mm2 at 4.2 K in 6 T, at 10 K in 4 T and at 20 K in 2 T. The results also show that cold drawing causes increase of n value.
- 5 May 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (17) , 173908
The critical parameters in in-situ MgB2 wires and tapes with ex-situ MgB2 barrier after hot isostatic pressure, cold drawing, cold rolling and doping
MgB2 precursor wires were prepared using powder in tube technique by Institute of High Pressure PAS in Warsaw. All samples were annealed under isostatic pressure generated by liquid Argon in the range from 0.3 GPa to 1 GPa. In this paper, we show the effects of different processing routes, namely, cold drawing (CD), cold rolling (CR), hot isostatic pressure (HIP) and doping on critical current density (Jc), pinning force (Fp), irreversible magnetic-field (Birr), critical temperature (Tc), n value, and dominant pinning mechanism in MgB2/Fe wires with ex situ MgB2 barrier. The results show that medium pressures (∼0.35 GPa) lead to high Jc in low and medium magnetic fields (0 T – 9 T). On the other hand, higher pressures (∼1 GPa) lead to enhanced Jc in high magnetic fields (above 9 T). Transport measurements show that CD, CR, and HIP have small effects on Birr and Tc, but CD, CR, HIP, and doping enhance Jc and Fp in in situ MgB2 wires with ex situ MgB2 barrier. Transport measurements on in situ undoped MgB2 wire with ex situ MgB2 barrier yield a Jc of about 100 A/mm2 at 4.2 K in 6 T, at 10 K in 4 T and at 20 K in 2 T. The results also show that cold drawing causes increase of n value.
- 20 April 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (15) , 153905
Electron paramagnetic resonance and Raman spectroscopy studies on carbon-doped MgB2 superconductor nanomaterials
Undoped and carbon-doped magnesium diboride (MgB2) samples were synthesized using two sets of mixtures prepared from the precursors, amorphous nanoboron, and as-received amorphous carbon-doped nanoboron. The microscopic defect structures of carbon-doped MgB2 samples were systematically investigated using X-ray powder diffraction, Raman and electron paramagnetic resonance spectroscopy. Mg vacancies and C-related dangling-bond active centers could be distinguished, and sp3-hybridized carbon radicals were detected. A strong reduction in the critical temperature Tc was observed due to defects and crystal distortion. The symmetry effect of the latter is also reflected on the vibrational modes in the Raman spectra.
- 20 April 2015
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 117 (15) , 153905
Electron paramagnetic resonance and Raman spectroscopy studies on carbon-doped MgB2 superconductor nanomaterials
Undoped and carbon-doped magnesium diboride (MgB2) samples were synthesized using two sets of mixtures prepared from the precursors, amorphous nanoboron, and as-received amorphous carbon-doped nanoboron. The microscopic defect structures of carbon-doped MgB2 samples were systematically investigated using X-ray powder diffraction, Raman and electron paramagnetic resonance spectroscopy. Mg vacancies and C-related dangling-bond active centers could be distinguished, and sp3-hybridized carbon radicals were detected. A strong reduction in the critical temperature Tc was observed due to defects and crystal distortion. The symmetry effect of the latter is also reflected on the vibrational modes in the Raman spectra.
- 3 December 2011
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 473, 34-40
Effect of heat treatment temperature on superconducting performance of B4C added MgB2/Nb conductors
- 3 December 2011
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 473, 34-40
Effect of heat treatment temperature on superconducting performance of B4C added MgB2/Nb conductors
- 30 June 2007
- Published by Springer Nature
- p. 753-768
AC properties of high-temperature superconductors
- 19 May 2004
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 406, 121-130
Critical current densities of superconducting MgB2 tapes prepared on the base of mechanically alloyed precursors
- 19 May 2004
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 406, 121-130
Critical current densities of superconducting MgB2 tapes prepared on the base of mechanically alloyed precursors