Maria Mitkova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Maria Mitkova has a total of 240 co-authors. Here are the top co-authors by number of shared publications:
M.N. Kozicki
13 shared publicationsMichael N. Kozicki
School of Electrical, Computer and Energy Engineering, Arizona State University Tempe AZ 85287‐5706 USA
12 shared publications- Dmitri A. Tenne
Department of Physics and Astronomy, Boise State University 5 , Boise, Idaho 83725
10 shared publications Y. Gonzalez-Velo
School of Electrical, Computer and Energy Engineering, Arizona State University, Tempe, AZ, USA
10 shared publicationsM. Ailavajhala
Boise State University, 1910 University Dr. Boise 3 Department of Electrical and Computer Engineering Idaho 83725-2075, USA
8 shared publicationsM. N. Kozicki
School of Electrical, Computer and Energy Engineering, Arizona State University, Tempe, AZ, USA
8 shared publications
Latest Publications
- Open Access
- 12 July 2021
- Published by Springer Nature in Scientific Reports
- Vol. 11 (1) , 1-15
Introduction of Chalcogenide Glasses to Additive Manufacturing: Nanoparticle Ink Formulation, Inkjet Printing, and Phase Change Devices Fabrication
Chalcogenide glasses are one of the most versatile materials that have been widely researched because of their flexible optical, chemical, electronic, and phase change properties. Their application is usually in the form of thin films, which work as active layers in sensors and memory devices. In this work, we investigate the formulation of nanoparticle ink of Ge–Se chalcogenide glasses and its potential applications. The process steps reported in this work describe nanoparticle ink formulation from chalcogenide glasses, its application via inkjet printing and dip-coating methods and sintering to manufacture phase change devices. We report data regarding nanoparticle production by ball milling and ultrasonication along with the essential characteristics of the formed inks, like contact angle and viscosity. The printed chalcogenide glass films were characterized by Raman spectroscopy, X-ray diffraction, energy dispersive spectroscopy and atomic force microscopy. The printed films exhibited similar compositional, structural, electronic and optical properties as the thermally evaporated thin films. The crystallization processes of the printed films are discussed compared to those obtained by vacuum thermal deposition. We demonstrate the formation of printed thin films using nanoparticle inks, low-temperature sintering and proof for the first time, their application in electronic and photonic temperature sensors utilizing their phase change property. This work adds chalcogenide glasses to the list of inkjet printable materials, thus offering an easy way to form arbitrary device structures for optical and electronic applications.
- 12 July 2021
- Published by Springer Nature in Scientific Reports
- Vol. 11 (1) , 1-15
Open AccessIntroduction of Chalcogenide Glasses to Additive Manufacturing: Nanoparticle Ink Formulation, Inkjet Printing, and Phase Change Devices Fabrication
Chalcogenide glasses are one of the most versatile materials that have been widely researched because of their flexible optical, chemical, electronic, and phase change properties. Their application is usually in the form of thin films, which work as active layers in sensors and memory devices. In this work, we investigate the formulation of nanoparticle ink of Ge–Se chalcogenide glasses and its potential applications. The process steps reported in this work describe nanoparticle ink formulation from chalcogenide glasses, its application via inkjet printing and dip-coating methods and sintering to manufacture phase change devices. We report data regarding nanoparticle production by ball milling and ultrasonication along with the essential characteristics of the formed inks, like contact angle and viscosity. The printed chalcogenide glass films were characterized by Raman spectroscopy, X-ray diffraction, energy dispersive spectroscopy and atomic force microscopy. The printed films exhibited similar compositional, structural, electronic and optical properties as the thermally evaporated thin films. The crystallization processes of the printed films are discussed compared to those obtained by vacuum thermal deposition. We demonstrate the formation of printed thin films using nanoparticle inks, low-temperature sintering and proof for the first time, their application in electronic and photonic temperature sensors utilizing their phase change property. This work adds chalcogenide glasses to the list of inkjet printable materials, thus offering an easy way to form arbitrary device structures for optical and electronic applications.
- Open Access
Chalcogenide Glass-Capped Fiber-Optic Sensor for Real-Time Temperature Monitoring in Extreme Environments
We demonstrate a novel chalcogenide glass (ChG)-capped optical fiber temperature sensor capable of operating within harsh environment. The sensor architecture utilizes the heat-induced phase change (amorphous-to-crystalline) property of ChGs, which rapidly (80–100 ns) changes the optical properties of the material. The sensor response to temperature variation around the phase change of the ChG cap at the tip of the fiber provides abrupt changes in the reflected power intensity. This temperature is indicative of the temperature at the sensing node. We present the sensing performance of six different compositions of ChGs and a method to interpret the temperature profile between 440 °C and 600 °C in real-time using an array structure. The unique radiation-hardness property of ChGs makes the devices compatible with high-temperature and high-radiation environments, such as monitoring the cladding temperature of Light Water (LWR) or Sodium-cooled Fast (SFR) reactors.
Open AccessChalcogenide Glass-Capped Fiber-Optic Sensor for Real-Time Temperature Monitoring in Extreme Environments
We demonstrate a novel chalcogenide glass (ChG)-capped optical fiber temperature sensor capable of operating within harsh environment. The sensor architecture utilizes the heat-induced phase change (amorphous-to-crystalline) property of ChGs, which rapidly (80–100 ns) changes the optical properties of the material. The sensor response to temperature variation around the phase change of the ChG cap at the tip of the fiber provides abrupt changes in the reflected power intensity. This temperature is indicative of the temperature at the sensing node. We present the sensing performance of six different compositions of ChGs and a method to interpret the temperature profile between 440 °C and 600 °C in real-time using an array structure. The unique radiation-hardness property of ChGs makes the devices compatible with high-temperature and high-radiation environments, such as monitoring the cladding temperature of Light Water (LWR) or Sodium-cooled Fast (SFR) reactors.
- 20 October 2020
- Published by Wiley in Physica Status Solidi (b)
- Vol. 258 (9) , 2000429
Effect of Ion Irradiation on Amorphous and Crystalline Ge–Se and Their Application as Phase Change Temperature Sensor
Research on phase change materials is predominantly focused on their application as memory devices or for temperature control which requires low phase change temperature. The Ge–Se binary chalcogenide glass system with its wide glass‐forming region is a potential candidate for high‐temperature and high‐radiation phase change applications. Herein, the concept of employing Ge x Se100−x glasses to monitor high temperature (450–528 °C) using the phase change effect, is reported. Materials selection, device structure, and performance of prototype sensors are analyzed. In addition, the effect of heavy ion irradiation by Xe ions with energies of 200, 600, and 1000 keV (fluence ≈1014 cm−2) on the Ge x Se100−x (x = 30, 33, 40) thin films and phase change devices is studied. The irradiation effect on the amorphous and crystalline structure of the thin films is evaluated by Raman spectroscopy and X‐ray diffraction (XRD). Although the changes in the structural units of amorphous films are negligible, in crystalline films orthorhombic‐GeSe2 crystals are found to be most affected by irradiation and a new phase, orthorhombic GeSe is found in the thin films after irradiation. The performance of a sensor with an active film of Ge40Se60 is also shown as an example.
- 20 October 2020
- Published by Wiley in Physica Status Solidi (b)
- Vol. 258 (9) , 2000429
Effect of Ion Irradiation on Amorphous and Crystalline Ge–Se and Their Application as Phase Change Temperature Sensor
Research on phase change materials is predominantly focused on their application as memory devices or for temperature control which requires low phase change temperature. The Ge–Se binary chalcogenide glass system with its wide glass‐forming region is a potential candidate for high‐temperature and high‐radiation phase change applications. Herein, the concept of employing Ge x Se100−x glasses to monitor high temperature (450–528 °C) using the phase change effect, is reported. Materials selection, device structure, and performance of prototype sensors are analyzed. In addition, the effect of heavy ion irradiation by Xe ions with energies of 200, 600, and 1000 keV (fluence ≈1014 cm−2) on the Ge x Se100−x (x = 30, 33, 40) thin films and phase change devices is studied. The irradiation effect on the amorphous and crystalline structure of the thin films is evaluated by Raman spectroscopy and X‐ray diffraction (XRD). Although the changes in the structural units of amorphous films are negligible, in crystalline films orthorhombic‐GeSe2 crystals are found to be most affected by irradiation and a new phase, orthorhombic GeSe is found in the thin films after irradiation. The performance of a sensor with an active film of Ge40Se60 is also shown as an example.
- 30 May 2020
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 31 (14) , 11211-11226
Phase change in Ge–Se chalcogenide glasses and its implications on optical temperature-sensing devices
- 30 May 2020
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 31 (14) , 11211-11226
Phase change in Ge–Se chalcogenide glasses and its implications on optical temperature-sensing devices
- 1 December 2019
- Published by International Association of Advanced Materials in Advanced Materials Letters
- Vol. 10 (12) , 868-873
Dual Effect of Light Irradiation for Surface Relief Gratings Formation in Se-rich Ge-Se Thin Films
- 1 December 2019
- Published by International Association of Advanced Materials in Advanced Materials Letters
- Vol. 10 (12) , 868-873
Dual Effect of Light Irradiation for Surface Relief Gratings Formation in Se-rich Ge-Se Thin Films
- Open Access
- 19 March 2019
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 3 (3) , 035601
Structural transformation in network glasses: Structural varieties in short-range, medium-range, and nanoscopic scalePrecise x-ray diffraction measurements using high-energy x rays of synchrotron radiation and systematic Raman scattering measurements were carried out for network glasses. The structural models of the network glasses were proposed based on the results. In the stoichiometric composition , tetrahedral units are connected forming either corner-sharing or edge-sharing structures. In the S-rich glasses, S atoms are inserted between two neighboring tetrahedra, resulting in a flexible floppy network. In a much more S-rich region, some ring molecules are isolated from the network, and assemble to form a crystal in nanoscopic scale. In this respect, samples are regarded as crystallized glasses. In the Ge-rich region, the tetrahedra are connected with bridging Ge atoms. The connection makes a new rigid network. The bridging Ge-S bond is weaker than the intratetrahedron bond, and this leads to drastic changes in the optical properties.- 19 March 2019
- Published by American Physical Society (APS) in Physical Review Materials
- Vol. 3 (3) , 035601
Open AccessStructural transformation in network glasses: Structural varieties in short-range, medium-range, and nanoscopic scalePrecise x-ray diffraction measurements using high-energy x rays of synchrotron radiation and systematic Raman scattering measurements were carried out for network glasses. The structural models of the network glasses were proposed based on the results. In the stoichiometric composition , tetrahedral units are connected forming either corner-sharing or edge-sharing structures. In the S-rich glasses, S atoms are inserted between two neighboring tetrahedra, resulting in a flexible floppy network. In a much more S-rich region, some ring molecules are isolated from the network, and assemble to form a crystal in nanoscopic scale. In this respect, samples are regarded as crystallized glasses. In the Ge-rich region, the tetrahedra are connected with bridging Ge atoms. The connection makes a new rigid network. The bridging Ge-S bond is weaker than the intratetrahedron bond, and this leads to drastic changes in the optical properties. - 15 December 2018
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 30 (3) , 2389-2402
CBRAM devices based on a nanotube chalcogenide glass structure
- 15 December 2018
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 30 (3) , 2389-2402
CBRAM devices based on a nanotube chalcogenide glass structure
- 11 December 2018
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 30 (3) , 2470-2478
Nanotube structures: material characterization and structural analysis of Ge–Se thin films
- 11 December 2018
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 30 (3) , 2470-2478
Nanotube structures: material characterization and structural analysis of Ge–Se thin films
- 20 June 2018
- Published by Wiley in Physica Status Solidi (a)
- Vol. 215 (12)
Kinetics of Silver Photodiffusion Into Amorphous Ge20S80 Films: Case of Pre‐Reaction (Phys. Status Solidi A 12∕2018)
- 20 June 2018
- Published by Wiley in Physica Status Solidi (a)
- Vol. 215 (12)
Kinetics of Silver Photodiffusion Into Amorphous Ge20S80 Films: Case of Pre‐Reaction (Phys. Status Solidi A 12∕2018)
- 24 March 2018
- Published by Wiley in Physica Status Solidi (a)
- Vol. 215 (12)
Kinetics of Silver Photodiffusion Into Amorphous Ge20S80 Films: Case of Pre‐Reaction
Silver photodiffusion into amorphous chalcogenide has attracted much attention because of its potential applications for example in memory devices. For its development, it is important to know how Ag ions diffuse in chalcogenide layers upon light exposure. In this paper, the photo‐induced effect on “pre‐reacted” films before light exposure, originating from Ag/Ge20S80/Si substrate and Ge20S80/Ag/Si substrate is investigated, using neutron reflectivity, X‐ray reflectivity, and X‐ray diffraction. Two types of “pre‐reacted” films according to the original stacking order are obtained. In both cases, a pure Ag layer almost disappeared, and there is a small amount of monoclinic Ag2S. The reaction time for the photodiffusion is shorter, in both cases, than that in Ag/Ge20S80 with a pure Ag layer, indicating a different reaction process. After prolonged light exposure, a uniform amorphous reaction layer is produced in the films originating from the Ag/Ge20S80/Si substrate, while both an amorphous reaction product and the Ag2S fragments exist in the films originating from Ge20S80/Ag/Si substrate. The mechanism of the specific photo‐reaction is discussed in terms of the role of the Ag2S fragments.
- 24 March 2018
- Published by Wiley in Physica Status Solidi (a)
- Vol. 215 (12)
Kinetics of Silver Photodiffusion Into Amorphous Ge20S80 Films: Case of Pre‐Reaction
Silver photodiffusion into amorphous chalcogenide has attracted much attention because of its potential applications for example in memory devices. For its development, it is important to know how Ag ions diffuse in chalcogenide layers upon light exposure. In this paper, the photo‐induced effect on “pre‐reacted” films before light exposure, originating from Ag/Ge20S80/Si substrate and Ge20S80/Ag/Si substrate is investigated, using neutron reflectivity, X‐ray reflectivity, and X‐ray diffraction. Two types of “pre‐reacted” films according to the original stacking order are obtained. In both cases, a pure Ag layer almost disappeared, and there is a small amount of monoclinic Ag2S. The reaction time for the photodiffusion is shorter, in both cases, than that in Ag/Ge20S80 with a pure Ag layer, indicating a different reaction process. After prolonged light exposure, a uniform amorphous reaction layer is produced in the films originating from the Ag/Ge20S80/Si substrate, while both an amorphous reaction product and the Ag2S fragments exist in the films originating from Ge20S80/Ag/Si substrate. The mechanism of the specific photo‐reaction is discussed in terms of the role of the Ag2S fragments.