Sanjeev Kumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sanjeev Kumar has a total of 232 co-authors. Here are the top co-authors by number of shared publications:
Arun Kumar Singh
31 shared publications- Gyaneshwar Sharma
Tilak Dhari Post Graduate College
20 shared publications Shobhna Dhiman
Physics Department, Punjab Engineering College (Deemed to be University), Chandigarh, India
15 shared publications- Arun Kumar Singh
Semiconductor Research Centre, Department of Electronics and Communication Engineering, Punjab Engineering College (Deemed to be University), Chandigarh, India
13 shared publications Mukul Kumar
11 shared publicationsManoj Kumar
Department of Physics, Punjab Engineering College (Deemed to be University), Physics Department, Punjab Engineering College (Deemed to be University), Chandigarh, India – 160012, Chandigarh, Punjab, 160012, INDIA
10 shared publications
Latest Publications
- 23 October 2026
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 8 (21) , 9459-9473
Machine-Learning-Enabled Flexible Piezoelectric Nanogenerator Based on PVDF/KNNBZ Nanofibers for Intelligent Human Motion Recognition
The performance of flexible piezoelectric nanogenerators (FPNGs) based on poly(vinylidene fluoride) (PVDF) remains limited due to a poor electroactive β-phase. The incorporation of ceramic fillers as nucleating agents into the PVDF matrix is one of the most effective strategies to enhance the β-phase content. However, conventional piezoelectric ceramics offer limited polarization. In contrast, relaxor ferroelectrics are characterized by dynamic polar nanoregions (PNRs) that readily reorient under external stimuli. This nanoscale responsiveness translates into significantly higher piezoelectric coefficients, markedly amplifying the performance of PVDF based FPNGs. Rather than relying on conventional piezoelectric ceramics, this work introduces Bi3+/Zr4+ co-doped potassium sodium niobate (K0.425Na0.425Bi0.15Nb0.85Zr0.15O3, KNNBZ) as a filler, chosen specifically for its relaxor nature. Simultaneous A- and B-site co-doping destabilizes long-range ferroelectric order and promotes the growth of PNRs. The electrostatic interaction between the negatively charged surface of KNNBZ and PVDF –CH2– dipoles locks chains into the all-trans β-phase conformation, reinforced further by the mechanical stretching and in-situ poling inherent to electrospinning. The optimized device generates an open-circuit voltage of 29 V and a peak power density of 76.3 μW/cm2 and directly powers commercial LEDs. Combined with a machine learning algorithm, the FPNG distinguishes location-specific gait signals with 95.56% accuracy, demonstrating practical utility for intelligent, self-powered wearable health monitoring.
- 23 October 2026
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 8 (21) , 9459-9473
Machine-Learning-Enabled Flexible Piezoelectric Nanogenerator Based on PVDF/KNNBZ Nanofibers for Intelligent Human Motion Recognition
The performance of flexible piezoelectric nanogenerators (FPNGs) based on poly(vinylidene fluoride) (PVDF) remains limited due to a poor electroactive β-phase. The incorporation of ceramic fillers as nucleating agents into the PVDF matrix is one of the most effective strategies to enhance the β-phase content. However, conventional piezoelectric ceramics offer limited polarization. In contrast, relaxor ferroelectrics are characterized by dynamic polar nanoregions (PNRs) that readily reorient under external stimuli. This nanoscale responsiveness translates into significantly higher piezoelectric coefficients, markedly amplifying the performance of PVDF based FPNGs. Rather than relying on conventional piezoelectric ceramics, this work introduces Bi3+/Zr4+ co-doped potassium sodium niobate (K0.425Na0.425Bi0.15Nb0.85Zr0.15O3, KNNBZ) as a filler, chosen specifically for its relaxor nature. Simultaneous A- and B-site co-doping destabilizes long-range ferroelectric order and promotes the growth of PNRs. The electrostatic interaction between the negatively charged surface of KNNBZ and PVDF –CH2– dipoles locks chains into the all-trans β-phase conformation, reinforced further by the mechanical stretching and in-situ poling inherent to electrospinning. The optimized device generates an open-circuit voltage of 29 V and a peak power density of 76.3 μW/cm2 and directly powers commercial LEDs. Combined with a machine learning algorithm, the FPNG distinguishes location-specific gait signals with 95.56% accuracy, demonstrating practical utility for intelligent, self-powered wearable health monitoring.
- Open Access
- 18 August 2026
- Published by Elsevier in SSRN Electronic Journal
Phosphatidylcholine-mediated Osteoinduction by 3D-Printed Antibacterial-Piezoelectric PLA-Ag-HA-NKN Scaffolds for Dental Regeneration
Osseointegration, inflammation, and bacterial infection remain major challenges for the current clinical gold standards- titanium and zirconium based dental implant systems. One promising solution involves the use of biomaterialbased implants for the regeneration of fully functional teeth. Piezoelectric materials generate electric charges under mechanical stress, mimicking endogenous electric fields to modulate intracellular signaling and ion flux, thereby promoting tissue regeneration. In this study, we fabricated silver doped Hydroxyapatite-NKN based 3D-printed piezoelectric and anti-bacterial nanocomposite scaffolds for dental regeneration. d33 value of synthesized HA20N composite was found to 24.33 ± 1.20pC/N. Incorporation of AgHANKN filler in the PLA matrix improved the hydrophilicity and the mechanical properties of the composite scaffolds. Composite scaffolds, H20N5P and H20N10P showed contact angle value of 65.09 ± 0.81° and 65.42 ± 1.17°, with Young’s modulus of 983.5 ± 112.4MPa and 801 ± 226.27MPa, and compressive strengths of 47.93 ± 0.41MPa and 48.91 ± 17.19MPa, respectively. H20N5P and H20N10P scaffolds exhibited excellent anti-bacterial properties against Staphylococcus aureus and Escherichia coli. In vitro studies involving MG63 cells confirmed that H20N10P scaffold markedly improved cell adhesion, proliferation, and osteogenic differentiation, with enhanced expression of osteogenic markers Col1, Col2, Runx2, and OPN. ¹H NMR-based metabolomic analysis revealed elevated Phosphatidylcholine levels in cells cultured on H20N10P scaffold. Phosphatidylcholine promotes osteogenesis by upregulating Runx2 expression contributing to mineralization through matrix vesicle-mediated production of inorganic phosphate (Pi). These results demonstrate that AgHANKN-PLA offers a multifunctional composite system with improved mechanical strength, selfgenerated electrical stimulation, antimicrobial efficacy, and osteoinductive capacity for enhanced dental regeneration.
- 18 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessPhosphatidylcholine-mediated Osteoinduction by 3D-Printed Antibacterial-Piezoelectric PLA-Ag-HA-NKN Scaffolds for Dental Regeneration
Osseointegration, inflammation, and bacterial infection remain major challenges for the current clinical gold standards- titanium and zirconium based dental implant systems. One promising solution involves the use of biomaterialbased implants for the regeneration of fully functional teeth. Piezoelectric materials generate electric charges under mechanical stress, mimicking endogenous electric fields to modulate intracellular signaling and ion flux, thereby promoting tissue regeneration. In this study, we fabricated silver doped Hydroxyapatite-NKN based 3D-printed piezoelectric and anti-bacterial nanocomposite scaffolds for dental regeneration. d33 value of synthesized HA20N composite was found to 24.33 ± 1.20pC/N. Incorporation of AgHANKN filler in the PLA matrix improved the hydrophilicity and the mechanical properties of the composite scaffolds. Composite scaffolds, H20N5P and H20N10P showed contact angle value of 65.09 ± 0.81° and 65.42 ± 1.17°, with Young’s modulus of 983.5 ± 112.4MPa and 801 ± 226.27MPa, and compressive strengths of 47.93 ± 0.41MPa and 48.91 ± 17.19MPa, respectively. H20N5P and H20N10P scaffolds exhibited excellent anti-bacterial properties against Staphylococcus aureus and Escherichia coli. In vitro studies involving MG63 cells confirmed that H20N10P scaffold markedly improved cell adhesion, proliferation, and osteogenic differentiation, with enhanced expression of osteogenic markers Col1, Col2, Runx2, and OPN. ¹H NMR-based metabolomic analysis revealed elevated Phosphatidylcholine levels in cells cultured on H20N10P scaffold. Phosphatidylcholine promotes osteogenesis by upregulating Runx2 expression contributing to mineralization through matrix vesicle-mediated production of inorganic phosphate (Pi). These results demonstrate that AgHANKN-PLA offers a multifunctional composite system with improved mechanical strength, selfgenerated electrical stimulation, antimicrobial efficacy, and osteoinductive capacity for enhanced dental regeneration.
- Open Access
- 15 August 2026
- Published by Elsevier in SSRN Electronic Journal
Tailoring Excellent Electrocaloric and Energy Storage Performance in Compositionally Manipulated BaTiO3-Based Ceramics Through the Synergistic Effect of Morphotropic Phase Boundary Evolution
A revival interest in barium titanate (BaTiO3) and its derivatives has been sparked by the recent focus on ecologically friendly and sustainable solid-state refrigeration and energy storage systems. Therefore, the main focus of current research is to develop lead-free ceramics that possess improved electrocaloric temperature change (ΔT) and energy storage performance at relatively low electric fields. Furthermore, tailoring phase boundaries is a potential way to enhance the electrocaloric and energy storage properties in ferroelectric ceramics. This is often accomplished using a composition variation approach. Consequently, in the present study, the electrocaloric effect and energy-storage performance of the BaHfxTi1-xO3 (BHT) ceramic were investigated with varied Hf concentrations x = 0, 10, and 0.15. XRD pattern analysis reveals the formation of multiple phase boundaries in Hf-modified BT ceramics, especially the morphotropic phase boundary (MPB) between tetragonal and orthorhombic phases, which emerges in BHT10 ceramic, and polymorphotropic phase boundaries (PPT) in BHT15 ceramic. The FESEM and dielectric results demonstrate that the incorporation of Hf in BT reduces the grain size, enhances the relaxation degree, and prompts the formation of DPT or relaxor-like characteristics with PNR. Compared to pure BT, the electrocaloric response and energy storage performance of BHT ceramics are remarkably enhanced by the Hf substitution. The BHT10 ceramic exhibited the highest electrocaloric temperature change, ΔTmax ~ 1.26 K, under an applied electric field of 40 kV/cm, and also a high electrocaloric responsivity of 0.32 K.mm/kV. High recoverable energy density Jrec ~ 186.53 × 10-3J/cm3 and a high efficiency η ~ 93.96% were also observed for the BHT10 ceramic. The improved microstructure, MPB evolution, and high relative density in the BHT10 sample collectively contribute to enhanced electrocaloric effect and improved energy storage response. Furthermore, Hf doping improves the thermal stability of temperature-dependent energy storage density, or Jrec, in BHT ceramics. These results broaden the scope of optimizing the environmentally friendly BT-based ceramic for solid-state refrigeration and pulse power capacitor applications.
- 15 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessTailoring Excellent Electrocaloric and Energy Storage Performance in Compositionally Manipulated BaTiO3-Based Ceramics Through the Synergistic Effect of Morphotropic Phase Boundary Evolution
A revival interest in barium titanate (BaTiO3) and its derivatives has been sparked by the recent focus on ecologically friendly and sustainable solid-state refrigeration and energy storage systems. Therefore, the main focus of current research is to develop lead-free ceramics that possess improved electrocaloric temperature change (ΔT) and energy storage performance at relatively low electric fields. Furthermore, tailoring phase boundaries is a potential way to enhance the electrocaloric and energy storage properties in ferroelectric ceramics. This is often accomplished using a composition variation approach. Consequently, in the present study, the electrocaloric effect and energy-storage performance of the BaHfxTi1-xO3 (BHT) ceramic were investigated with varied Hf concentrations x = 0, 10, and 0.15. XRD pattern analysis reveals the formation of multiple phase boundaries in Hf-modified BT ceramics, especially the morphotropic phase boundary (MPB) between tetragonal and orthorhombic phases, which emerges in BHT10 ceramic, and polymorphotropic phase boundaries (PPT) in BHT15 ceramic. The FESEM and dielectric results demonstrate that the incorporation of Hf in BT reduces the grain size, enhances the relaxation degree, and prompts the formation of DPT or relaxor-like characteristics with PNR. Compared to pure BT, the electrocaloric response and energy storage performance of BHT ceramics are remarkably enhanced by the Hf substitution. The BHT10 ceramic exhibited the highest electrocaloric temperature change, ΔTmax ~ 1.26 K, under an applied electric field of 40 kV/cm, and also a high electrocaloric responsivity of 0.32 K.mm/kV. High recoverable energy density Jrec ~ 186.53 × 10-3J/cm3 and a high efficiency η ~ 93.96% were also observed for the BHT10 ceramic. The improved microstructure, MPB evolution, and high relative density in the BHT10 sample collectively contribute to enhanced electrocaloric effect and improved energy storage response. Furthermore, Hf doping improves the thermal stability of temperature-dependent energy storage density, or Jrec, in BHT ceramics. These results broaden the scope of optimizing the environmentally friendly BT-based ceramic for solid-state refrigeration and pulse power capacitor applications.
- Open Access
- 24 February 2026
- Published by Elsevier in SSRN Electronic Journal
Morphotropic Phase Boundary Engineering: Unlocking High-Performance Low-Field Electrocaloric and Energy Storage Responses in Lead-Free BCST Ceramics
Lead-free ferroelectric ceramics hold significant promise for capacitive energy storage and solid-state cooling applications. However, attaining high energy density and efficiency simultaneously remains a critical challenge in dielectric capacitor research, as the limited saturation polarization of barium titanate fundamentally constrains its achievable energy storage density. Similarly, achieving effective electrocaloric cooling at room temperature is crucial for solid-state cooling solutions. Since barium titanate shows strong electrocaloric effects near its Curie temperature, adjusting this temperature to near room temperature through morphotropic phase boundary (MPB) development is advantageous. In this work, Sn4+ substitution content is optimized as a B-site cation to create MPB with rhombohedral-orthorhombic-tetragonal phase coexistence, nanoscale polar regions and relaxor-like features in BCST ceramics. This approach enhances energy storage density to Wrec ~ 118 mJ/cm3, Wtot ~ 179 mJ/cm3, and η ~ 66% for the sample with optimized Sn4+ concentration i.e. Ba0.95Ca0.05Sn0.09Ti0.91O3. It also exhibits a notable electrocaloric cooling effect with ΔT ~ 1.4K, ΔS ~ 1.67 J/kg K, ΔT/ΔE ~ 0.32 K.mm/kV and ΔS/ΔE ~ 0.42 J.mm/K.kg.kV. The results offer a novel approach for relatively high energy storage density and electrocaloric cooling in BCST ceramics at ambient temperatures, providing a practical pathway for advancing capacitive energy storage and electrocaloric cooling technologies.
- 24 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMorphotropic Phase Boundary Engineering: Unlocking High-Performance Low-Field Electrocaloric and Energy Storage Responses in Lead-Free BCST Ceramics
Lead-free ferroelectric ceramics hold significant promise for capacitive energy storage and solid-state cooling applications. However, attaining high energy density and efficiency simultaneously remains a critical challenge in dielectric capacitor research, as the limited saturation polarization of barium titanate fundamentally constrains its achievable energy storage density. Similarly, achieving effective electrocaloric cooling at room temperature is crucial for solid-state cooling solutions. Since barium titanate shows strong electrocaloric effects near its Curie temperature, adjusting this temperature to near room temperature through morphotropic phase boundary (MPB) development is advantageous. In this work, Sn4+ substitution content is optimized as a B-site cation to create MPB with rhombohedral-orthorhombic-tetragonal phase coexistence, nanoscale polar regions and relaxor-like features in BCST ceramics. This approach enhances energy storage density to Wrec ~ 118 mJ/cm3, Wtot ~ 179 mJ/cm3, and η ~ 66% for the sample with optimized Sn4+ concentration i.e. Ba0.95Ca0.05Sn0.09Ti0.91O3. It also exhibits a notable electrocaloric cooling effect with ΔT ~ 1.4K, ΔS ~ 1.67 J/kg K, ΔT/ΔE ~ 0.32 K.mm/kV and ΔS/ΔE ~ 0.42 J.mm/K.kg.kV. The results offer a novel approach for relatively high energy storage density and electrocaloric cooling in BCST ceramics at ambient temperatures, providing a practical pathway for advancing capacitive energy storage and electrocaloric cooling technologies.
- Open Access
- 18 February 2026
- Published by Springer Nature in Research Square
Multifunctional Pyroelectric and Electrocaloric response through Eu3+ doping in 0.55Pb(Ni1/3Nb2/3)O3-0.135PbZrO3-0.315PbTiO3 ceramics at Morphotropic Phase Boundary
This study presents a strategy to enhance the pyroelectric and electrocaloric responses at room temperature by tailoring the Landau free-energy landscape of a ternary morphotropic phase boundary (MPB) composition 0.55Pb(Ni 1/3 Nb 2/3 )O 3 -0.135PbZrO 3 -0.315PbTiO 3 + xEu 2 O 3 (x = 0, 0.01 & 0.02). Eu 3+ substitution at the A-site reduces the effective ionic spacing, inducing octahedral tilting and stabilizing a lower-symmetry crystal structure, predominantly rhombohedral, in the vicinity of room temperature. The associated local lattice distortion and charge imbalance promote relaxor behaviour in the PNN-PZ-PT system. A pronounced enhancement in pyroelectric performance is observed for the x = 0.02 composition, with the pyroelectric coefficient reaching ~ 33.34 ×10 − 4 C/m 2 K and the corresponding pyroelectric figures of merits (FOMs) attain values of \(\:{F}_{i}\) ~ 1993 pm/V, \(\:{F}_{v}\) ~ 0.01592 m 2 /C, \(\:{F}_{d}\) ~23.57 µ(Pa) −0.5 , \(\:{F}_{e}\) ~107 Jm 3 /K and \(\:{F}_{e}^{*}\) ~26.48 pm 3 /N. Notably, electrocaloric measurements reveal the emergence of an orthorhombic phase near room temperature, resulting in an improved electrocaloric temperature change. Concurrently, Eu 3+ doping suppresses the inverse piezoelectric coefficient (\(\:{d}_{33}^{*}\)) from 1036 pm/V for x = 0 to 460 pm/V for x = 0.02 sample indicating reduced electromechanical coupling, while the energy storage density exhibits an improvement near the ferroelectric-paraelectric phase transition. These findings demonstrate that Eu 3+ modified PNN-PZ-PT ceramics offer a tunable multifunctional platform with potential applications in solid-state cooling, infrared detection, and thermal energy harvesting.- 18 February 2026
- Published by Springer Nature in Research Square
Open AccessMultifunctional Pyroelectric and Electrocaloric response through Eu3+ doping in 0.55Pb(Ni1/3Nb2/3)O3-0.135PbZrO3-0.315PbTiO3 ceramics at Morphotropic Phase Boundary
This study presents a strategy to enhance the pyroelectric and electrocaloric responses at room temperature by tailoring the Landau free-energy landscape of a ternary morphotropic phase boundary (MPB) composition 0.55Pb(Ni 1/3 Nb 2/3 )O 3 -0.135PbZrO 3 -0.315PbTiO 3 + xEu 2 O 3 (x = 0, 0.01 & 0.02). Eu 3+ substitution at the A-site reduces the effective ionic spacing, inducing octahedral tilting and stabilizing a lower-symmetry crystal structure, predominantly rhombohedral, in the vicinity of room temperature. The associated local lattice distortion and charge imbalance promote relaxor behaviour in the PNN-PZ-PT system. A pronounced enhancement in pyroelectric performance is observed for the x = 0.02 composition, with the pyroelectric coefficient reaching ~ 33.34 ×10 − 4 C/m 2 K and the corresponding pyroelectric figures of merits (FOMs) attain values of \(\:{F}_{i}\) ~ 1993 pm/V, \(\:{F}_{v}\) ~ 0.01592 m 2 /C, \(\:{F}_{d}\) ~23.57 µ(Pa) −0.5 , \(\:{F}_{e}\) ~107 Jm 3 /K and \(\:{F}_{e}^{*}\) ~26.48 pm 3 /N. Notably, electrocaloric measurements reveal the emergence of an orthorhombic phase near room temperature, resulting in an improved electrocaloric temperature change. Concurrently, Eu 3+ doping suppresses the inverse piezoelectric coefficient (\(\:{d}_{33}^{*}\)) from 1036 pm/V for x = 0 to 460 pm/V for x = 0.02 sample indicating reduced electromechanical coupling, while the energy storage density exhibits an improvement near the ferroelectric-paraelectric phase transition. These findings demonstrate that Eu 3+ modified PNN-PZ-PT ceramics offer a tunable multifunctional platform with potential applications in solid-state cooling, infrared detection, and thermal energy harvesting. - 11 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (11) , 15325-15334
Tuning magnetodielectric coupling in Bi3.15Nd0.85Ti3-x(Fex/2Eux/2)O12 ceramics: Unveiling structure–property interplay in multiferroic ceramics
- 11 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (11) , 15325-15334
Tuning magnetodielectric coupling in Bi3.15Nd0.85Ti3-x(Fex/2Eux/2)O12 ceramics: Unveiling structure–property interplay in multiferroic ceramics