CHChia-Jui Hsu

Chia-Jui Hsu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Chia-Jui Hsu has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Se Nanopowder Conversion into Lubricious 2D Selenide Layers by Tribochemical Reactions

    by Philipp G. Grützmacher, Michele Cutini, Edoardo Marquis, Manel Rodríguez Ripoll, Helmut Riedl, Philip Kutrowatz, Stefan Bug, Chia‐Jui Hsu, Johannes Bernardi, Carsten Gachot, et al.

    Transition metal dichalcogenide (TMD) coatings have attracted enormous scientific and industrial interest due to their outstanding tribological behavior. The paradigmatic example is MoS2, even though selenides and tellurides have demonstrated superior tribological properties. Here, an innovative in operando conversion of Se nanopowders into lubricious 2D selenides, by sprinkling them onto sliding metallic surfaces coated with Mo and W thin films, is described. Advanced material characterization confirms the tribochemical formation of a thin tribofilm containing selenides, reducing the coefficient of friction down to below 0.1 in ambient air, levels typically reached using fully formulated oils. Ab initio molecular dynamics simulations under tribological conditions reveal the atomistic mechanisms that result in the shear‐induced synthesis of selenide monolayers from nanopowders. The use of Se nanopowder provides thermal stability and prevents outgassing in vacuum environments. Additionally, the high reactivity of the Se nanopowder with the transition metal coating in the conditions prevailing in the contact interface yields highly reproducible results, making it particularly suitable for the replenishment of sliding components with solid lubricants, avoiding the long‐lasting problem of TMD‐lubricity degradation caused by environmental molecules. The suggested straightforward approach demonstrates an unconventional and smart way to synthesize TMDs in operando and exploit their friction‐ and wear‐reducing impact.


  • Open Access

    Revealing the interface nature of ZDDP tribofilm by X-ray photoelectron spectroscopy and atom probe tomography

    by Chia-Jui Hsu, Jenifer Barrirero, Rolf Merz, Andreas Stratmann, Hisham Aboulfadl, Georg Jacobs, Michael Kopnarski, Frank Mücklich, Carsten Gachot

    Purpose: To decrease wear and friction, zinc dialkyldithiophosphate (ZDDP) has been used in engine oil for several decades, but the mechanism of the tribofilm formation is still unclear. The purpose of this study is to characterize the chemical details of the tribofilm by using high-resolution approaching.Design/methodology/approach: An ISO VG 100 mineral oil mixed with ZDDP was used in sliding tests on cylindrical roller bearings. Tribofilm formation was observed after 2 h of the sliding test. X-ray photoelectron spectroscopy (XPS) and atom probe tomography (APT) were used for chemical analysis of the tribofilm.Findings: The results show that the ZDDP tribofilm consists of the common ZDDP elements along with iron oxides. A considerable amount of zinc and a small amount of sulfur were observed. In particular, an oxide interlayer with sulfur enrichment was revealed by APT between the tribofilm and the steel substrate. The depth profile of the chemical composition was obtained, and a tribofilm of approximately 40 nm thickness was identified by XPS.Originality/value: A sulfur enrichment at the interface is observed by APT, which is beneath an oxygen enrichment. The clear evidence of the S interlayer confirms the hard and soft acids and bases principle.Peer review: The peer review history for this article is available at:https://publons.com/publon/10.1108/ILT-01-2020-0035/


  • Open Access

    Influence of Laser Pulse Number on the Ablation of Cemented Tungsten Carbides (WC-CoNi) with Different Grain Size

    by Shiqi Fang, Chia-Jui Hsu, Sven Klein, Luis Llanes, Dirk Bähre, Frank Mücklich

    The ultra-short pulse laser has attracted attention as an advanced tool for functionalizing surface topography, since it has high accuracy and results in little damage. In a previous study, some innovative patterns were introduced on cemented carbide surfaces, such as dimples, which are commonly used as oil reservoirs for bearings. The accuracy is not only related to the inherent features of the laser, but also to the machining processes. Within this context, this study aims to investigate the influence of machining parameters (i.e., pulse number in this study) on the ablation mechanism and resulting surface integrity. Two cemented carbide grades, possessing similar chemical composition but different grain size (small and large), are machined using a femtosond laser set-up with variant pulse number (1–20). The geometrical properties of the produced structure and surface integrity are statistically investigated using different microscopy techniques. It is found that the dimple depth is approximately proportional to the pulse number for both grades, and the coarse grade leads to a higher rate of depth increase. Damage is found in the form of melting and cracking for the binder and the grains, respectively; but this is more pronounced for large-grain grade in terms of the scale and depth. However, these observations are only found at a very superficial position.


  • Open Access

    Enhanced Growth of ZDDP-Based Tribofilms on Laser-Interference Patterned Cylinder Roller Bearings

    by Chia-Jui Hsu, Andreas Stratmann, Andreas Rosenkranz, Carsten Gachot

    Laser surface texturing has been successfully applied in the past to various machine elements in order to improve their tribological performance. In this study, direct laser interference patterning was used to produce periodic cross-like surface patterns on commercial cylinder roller bearings. The wear behavior of as-patterned bearings was studied by a modified FE8 test rig under boundary lubrication. A mineral oil (ISO VG 100) as a base oil additivated with 0.02 wt % zinc dialkyldithiophosphate (ZDDP) was used for the tribological tests which were performed under a Hertzian pressure of 1.92 GPa and maintained at 80 °C and 20 rpm for 2 h. The laser-patterned bearings showed a significantly reduced mass loss by two orders of magnitude compared to the unpatterned reference bearings. A closer look at the samples proved the formation of the characteristic blue-colored ZDDP tribofilm on top of the laser-induced topography maximum positions. Due to the higher contact pressure at the laser-induced peaks, the tribofilm formation was preferable at those positions thus protecting against wear. The laser patterns nearly remained unworn compared to the reference samples. A subsequent Raman analysis of the laser-patterned bearings clearly revealed the formation of zinc and iron sulfides as well as phosphates at the peak points.


  • Antiwear tribofilm growth in rolling bearings under boundary lubrication conditions

    by Andreas Stratmann, Georg Jacobs, Chia-Jui Hsu, Carsten Gachot, Gero Burghardt


  • Open Access

    Microstructural and Chemical Characterization of the Tribolayer Formation in Highly Loaded Cylindrical Roller Thrust Bearings

    by Carsten Gachot, ChiaJui Hsu, Sebastián Suárez, Philipp Grützmacher, Andreas Rosenkranz, Andreas Stratmann, Georg Jacobs

    Zinc dithiophosphates (ZDDP) have been widely applied in automobile industry for over 70 years as a lubricant additive for wear protection. Tribolayers have been described as blue- and brown-colored layers on surfaces observed by microscopical observation or even bare eye presumably as a consequence of layer thickness or chemical composition. However, the reaction pathways of ZDDP tribolayers are still not yet fully understood. In the present study, the difference between the blue- and brown-colored tribolayers has been revealed by high resolution methods in cylindrical roller thrust bearings at relatively high contact pressures of around 1.92 GPa. After running a FE8 standard bearing test with a normal load of 80 kN and a temperature of 60 °C, said tribolayers could be identified on the bearing surfaces. By using Raman spectroscopy, it could be shown that the blue-colored layers are enriched by FeS and ZnS whereas the brown-colored layers show a significant amount of Fe3O4. This is an interesting finding as it clearly shows a correlation between the color appearance of the films and the chemical composition besides potential film thickness variations. Finally, transmission electron microscopy verified the amorphous nature of the formed tribolayer which is in a good agreement with literature.


  • Effects of Tungsten Addition on Mechanical and Tribological Properties of Carbon Nitride Prepared by DC Magnetron Sputtering

    by Yean Liang Su, Yueh Feng Lin, Shun Hui Yao, Chia Jui Hsu

    Carbon nitride coatings doped with tungsten were deposited on high speed steel disks by unbalanced DC magnetron sputtering using nitrogen-argon mixture gas. The coatings were deposited on three different types of interlayer (Ti, Ti/TiN and Ti/TiC), and the tungsten target current was varied from 0 to 0.9 A. Surface morphology of the coatings were measured by roughness testing and scanning electron microscopy (SEM). In addition, the chemical composition and depth profile were analyzed by X-ray Diffraction (XRD) analysis, Raman spectroscopy, and glow discharge spectroscopy (GDS). Finally, the hardness (H) and elasticity (E) were measured by nanoindentation and a Rockwell indentation test, while the tribological properties were tested using a pin-on-disk tribometer. After all, the coatings were measured by cutting testing of tuning inserts and micro-drillers. It is found that all of the coatings are amorphous and have a thickness of approximately 1.5 μm. Moreover, the nitrogen content is around 30 at%, while the tungsten content varies in the range of 0-9 at%. In addition, the hardness values are in the range of 15-20 GPa and the elasticity varies from 236 to 274 GPa. A good correlation is observed between the wear resistance and the indentation adhesion level. Furthermore, it is found that the hardness is not significantly correlated to the tungsten content and the coatings deposited on the Ti/TiC interlayer have greater adhesion. Finally, the coatings generally have a very low coefficient of friction (0.01-0.3) and a wear coefficient as low as 10-6 mm3/Nm, and the CN/TiC coating reduced 41% and 43% of flank wear in the cutting testing of turning inserts and micro-drillers respectively.