Sarai Agustin-Salazar

This study evaluates the performance of major types of conventional and bio-based plastic items commonly used in agriculture to provide comprehensive insights into their key structural and functional properties, including the chemical composition of the polymer matrix and additives, mechanical behavior, and thermal and radiometric properties. Twelve agricultural plastic (AP) items were analyzed: covering mulch films, geotextile ground cover, protection fleece and low tunnel fleece cover, fertilizer sack, fly trap, irrigation pipe, tree binding net, guide for tree, silage film and hay bales protection fabric. This selection of APs also encompasses a broad range of basic polymers, including conventional materials (mainly polyethylene and polypropylene) and bio-based formulations (primarily starch- or lignocellulose-containing blends). Mass spectrometry and infrared spectroscopy analyses were performed to assess polymer composition and additives. Mechanical properties were assessed through tensile and puncture tests; in addition, radiometric, thermogravimetric, surface wettability, water absorption and permeability tests were also performed to assess other relevant physical characteristics. The study identified significant differences among bio-based biodegradable APs and compared them with their conventional polyolefin-based counterparts. Material composition and structure were found to critically influence water interactions, shaping the balance between durability, degradation, and crop protection performance. Notably, bio-based mulch films exhibited higher water vapor permeability (0.6–1.1 × 10⁻¹³ g/m Pa s), reduced penetration resistance (12.1 N) and lowered impact and tensile strengths (21.8 MPa). Water interaction tests showed that the starch-based mulch film displayed very high swelling (above 100%), favoring biodegradation, whereas a biodegradable blend based on polyhydroxybutyrate and polybutylene succinate exhibited minimal swelling (−13 g/m Pa s), while fibrous or biodegradable materials allowed enhanced vapor permeability. The results of this study, highlighting functionality, advantages and limitations of biodegradable APs versus conventional APs, are intended to guide future innovation in AP design, ensuring alignment with both the operational demands of modern agriculture and environmental sustainability goals. The data obtained from this study can support scientific advancements and policy recommendations on the use and management of plastics in agriculture.

Electrospinning and electrospraying nanotechnologies were used to valorise agro-industrial residues into biohybrid controlled-release polyphenol (CRP) scaffolds. Four polyhydroxybutyrate ± polycaprolactone (PHB±PCL) architectures were fabricated that differed in polymer phase, Klason lignin from hazelnut shell (HS-KL) presence vs. absence, and co-location with grape-pomace polyphenols (GP-PPs), as well as in distribution between fibres and bead-like depots. Scaffolds were characterised using optical microscopy/stereomicroscopy/SEM, FTIR, UV–Vis spectroscopy, and dynamic water contact angle (absorption). GP-PP release was monitored for 14 days at ~25 °C and 37 °C, the latter representing shallow-soil hot-spell conditions in Mediterranean zones. All matrices exhibited multimodal release, with modest initial bursts and three phases (burst, mid, and late tail), analogous to controlled-release fertiliser profiles. At ~25 °C, the PHB/PCL matrix with HS-KL confined to PHB fibres and GP-PP in large PCL beads showed the highest total GP-PP release, whereas the architecture with HS-KL and GP-PP co-located in both PHB and PCL fibres and in PCL depots combined high total release with a smoother, well-metered late phase. At 37 °C, this HS-KL-GP-PP co-located scaffold was the most robust, retaining the highest total and late tail release. These results identify HS-KL-GP-PP co-located PHB/PCL architectures as promising carriers for temperature-resilient delivery of bioactive polyphenols in Mediterranean agrosystems.

Electrospinning and electrospraying nanotechnologies were used to valorise agro-industrial residues into biohybrid controlled-release polyphenol (CRP) scaffolds. Four polyhydroxybutyrate ± polycaprolactone (PHB±PCL) architectures were fabricated that differed in polymer phase, Klason lignin from hazelnut-shell (HS-KL) presence vs absence and co-location with grape-pomace polyphenols (GP-PP), as well as distribution between fibres and bead-like depots. Scaffolds were characterised using optical microscopy/stereomicroscopy/SEM, FTIR, UV/VIS spectroscopy and dynamic water contact angle (absorption). GP-PP release was monitored for 14 days at ~25 °C and 37 °C, the latter representing shallow-soil hot-spell conditions in Mediterranean zones. All matrices exhibited multimodal release, with modest initial bursts and three phases ( burst, mid, and late tail), analogous to controlled-release fertiliser profiles. At ~25 °C, the PHB/PCL matrix with HS-KL confined to PHB fibres and GP-PP in large PCL beads showed the highest total GP-PP release, whereas the architecture with HS-KL and GP-PP co-located in both PHB and PCL fibres and in PCL depots combined high total release with a smoother, well-metered late phase. At 37 °C, this HS-KL-GP-PP co-located scaffold was the most robust, retaining the highest total and late tail release. These results identify HS-KL-GP-PP co-located PHB/PCL architectures as promising carriers for temperature-resilient delivery of bioactive polyphenols in Mediterranean agrosystems.

The use of natural bioactive compounds in edible coatings provides a sustainable approach to reducing food spoilage and meeting consumer demand for safer food preservation. In this study, bioactive extracts from Brassica juncea (green mustard, GM) and Raphanus sativus (radish tango, RT) sprouts were encapsulated into zein/chitosan (Z/CH) microparticles (MPs) using a complex coacervation–based encapsulation approach. The encapsulated microparticles (MPs), characterized by FTIR and UV-Vis spectroscopy, demonstrated a high loading efficiency of up to 90% and maintained their antioxidant activity for up to 168 h. TGA and SEM tests confirmed that the edible films produced by incorporating these microparticles (MPs) into polyvinyl alcohol (PVA) and chitosan (CH) matrices had a more uniform microstructure and enhanced heat stability. The Z/CH/RT6:PVA (1:2) and Z/CH/GM6:CH (1:1) formulations of the films showed significant antioxidant and antibacterial action, with up to 22.4% DPPH inhibition and a 1-log decrease in Salmonella enterica CFU, respectively. Overall, the results underscore the promise of sprout-derived microparticles as components for developing active, biodegradable packaging films with improved functional properties.

Global pecan nut production is projected to generate USD 3

Contamination of water bodies is a significant global issue that results from the deliberate release of pollutants into the environment, especially from mining and metal processing industries. The main pollutants generated by these industries are metallic wastes, particularly metals, which can cause adverse effects on the environment and human health. Therefore, it is crucial to develop effective and sustainable approaches to prevent their discharge into the environment. Biofiltration is a technique used to remediate contaminated fluids using biological processes. Microorganisms and agro-industrial wastes have been used successfully as biosorbents. Hence, this review emphasizes the innovative use of agro-industrial waste reinforced with microbial biomass as bioadsorbents, highlighting their dual capacity for metal removal through various bioremediation mechanisms. The mechanisms at play in these biocomposite materials, which offer enhanced sustainability, are also analyzed. This study contributes to the advancement of knowledge by suggesting new strategies for integrating reinforced materials in biosorption processes, thus providing a novel perspective on the potential of lignocellulosic-based systems to improve decontamination efforts. On the other hand, it shows some studies where the optimization and scaling-up of biosorption processes are reported. Additionally, the implementation of multisystem approaches, leveraging multiple bioremediation techniques simultaneously, can further enhance the efficiency and sustainability of metal removal in contaminated environments. Graphical abstract

Mining has led to severe environmental pollution in countries with exhaustive mining production and inadequate industrial waste regulation. Microorganisms in contaminated sites, like mine tailings, have adapted to high concentrations of heavy metals, developing the capacity of reducing or removing them from these environments. Therefore, it is essential to thoroughly characterize bacteria present in these sites to find different ways of bioremediation. In this regard, in this study, an enrichment and isolation procedure were performed to isolate bacteria with lower nutritional requirements and high tolerance to Cu(II) and Fe(II) from two Sonoran River basin mining tails. Two Staphylococcus species and a Microbacterium ginsengisoli strain were isolated and identified from the San Felipe de Jesús mining tail. Also, three strains were isolated from the Nacozari de García mining tail: Burkholderia cenocepacia, Sphingomonas sp. and Staphylococcus warneri. Significant microbiological differences were found between the two sites. All these species exhibited tolerance up to 300 mg/L for Cu (II)–Fe (II) solutions, indicating their capacity to grow in these conditions. Moreover, a consortium of isolated bacteria was immobilized in two different biocomposites and the biocomposite with larger pore size achieved greater bacterial immobilization showcasing the potential of these bacteria in biotechnological applications.