N. Sharma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
N. Sharma has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
M. Hooda
Department of Space
4 shared publicationsS. K. Sharma
Indian Institute of Technology (Indian School of Mines), Dhanbad India
3 shared publications- Manish Kumar Hooda
Ministry of Electronics and Information Technology (MeitY)
1 shared publication - S. K. Sharma
Department of Applied Physics, Indian School of Mines, Dhanbad, India
1 shared publication S.K. Sharma
Indian School of Mines
1 shared publication
Latest Publications
- 8 January 2024
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 70 (7) , 6437-6443
Silicon based Dielectric for Integrated Circuits – An Experimental Study
- 8 January 2024
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 70 (7) , 6437-6443
Silicon based Dielectric for Integrated Circuits – An Experimental Study
- 27 August 2018
- Published by Springer Nature in Indian Journal of Physics
- Vol. 93 (2) , 159-167
Stresses in thin films: an experimental study
- 27 August 2018
- Published by Springer Nature in Indian Journal of Physics
- Vol. 93 (2) , 159-167
Stresses in thin films: an experimental study
- 1 June 2018
- Published by American Scientific Publishers in Materials Express
- Vol. 8 (3) , 223-233
Qualification of silicon based oxide and nitride films for metal-insulator-metal capacitors
In this work, recipes for plasma enhanced chemically vapour deposited (PECVD) dielectric thin films of silicon dioxide (SiO2) and silicon nitride (Si3N4) were prepared. Each layer was deposited, characterized and verified for reproducibility. Revealed characterization results qualify these films for insulator in high density reliable metal-insulator-metal (MIM) capacitor. MIM capacitors array were successfully developed using stacked SiO2–Si3N4–SiO2 (ONO) thin films and characterized. Defects, voids and uniformity of deposited thin films were checked. Various types of conduction mechanism in ONO studied. The ONO dielectric film has high dielectric constant and breakdown voltage. It was observed that MIM capacitors have high precision and stable capacitance value in wide range of operating conditions. Ultra large scale integrated circuit (ULSIC) requires these MIM capacitors in various applications. Micro-electro-mechanical system (MEMS) uses these ONO films in RF switches.
- 1 June 2018
- Published by American Scientific Publishers in Materials Express
- Vol. 8 (3) , 223-233
Qualification of silicon based oxide and nitride films for metal-insulator-metal capacitors
In this work, recipes for plasma enhanced chemically vapour deposited (PECVD) dielectric thin films of silicon dioxide (SiO2) and silicon nitride (Si3N4) were prepared. Each layer was deposited, characterized and verified for reproducibility. Revealed characterization results qualify these films for insulator in high density reliable metal-insulator-metal (MIM) capacitor. MIM capacitors array were successfully developed using stacked SiO2–Si3N4–SiO2 (ONO) thin films and characterized. Defects, voids and uniformity of deposited thin films were checked. Various types of conduction mechanism in ONO studied. The ONO dielectric film has high dielectric constant and breakdown voltage. It was observed that MIM capacitors have high precision and stable capacitance value in wide range of operating conditions. Ultra large scale integrated circuit (ULSIC) requires these MIM capacitors in various applications. Micro-electro-mechanical system (MEMS) uses these ONO films in RF switches.
- 1 January 2016
- Published by Diva Enterprises Private Limited in Invertis Journal of Science & Technology
- Vol. 9 (2) , 118-126
Characterization of PECVD thin films for MEMS/NEMS applications
Due to the unique structure and small scale of MEMS/NEMS, the inherent residual stresses during the deposition processes can have a profound effect on the functionality and reliability of the fabricated MEMS/NEMS devices. Residual stress often causes device failure due to curling, buckling, or fracture. Typically, the material properties of thin films used in surface micromachining are not controlled during deposition. In this research, plasma enhanced chemical vapour deposition (PECVD) method is explored to produce nearly residual stress free silicon nitride and silicon dioxide thin films at 400°C. Process parameters, such as power, frequency mode, reactants flow rate and ratio, temperature and pressureinfluences the nature and magnitude of stress. The reduced residual stress levels can significantly improve device performance, reliability, and yield as these devices become smaller. Other properties Refractive index, thickness, thickness uniformity, and composition are studied to assess the quality of these films.
- 1 January 2016
- Published by Diva Enterprises Private Limited in Invertis Journal of Science & Technology
- Vol. 9 (2) , 118-126
Characterization of PECVD thin films for MEMS/NEMS applications
Due to the unique structure and small scale of MEMS/NEMS, the inherent residual stresses during the deposition processes can have a profound effect on the functionality and reliability of the fabricated MEMS/NEMS devices. Residual stress often causes device failure due to curling, buckling, or fracture. Typically, the material properties of thin films used in surface micromachining are not controlled during deposition. In this research, plasma enhanced chemical vapour deposition (PECVD) method is explored to produce nearly residual stress free silicon nitride and silicon dioxide thin films at 400°C. Process parameters, such as power, frequency mode, reactants flow rate and ratio, temperature and pressureinfluences the nature and magnitude of stress. The reduced residual stress levels can significantly improve device performance, reliability, and yield as these devices become smaller. Other properties Refractive index, thickness, thickness uniformity, and composition are studied to assess the quality of these films.
- Open Access
- 14 April 2014
- Published by Hindawi Limited in Journal of Materials
- Vol. 2014, 1-8
Synthesis and Characterization of LPCVD Polysilicon and Silicon Nitride Thin Films for MEMS Applications
Inherent residual stresses during material deposition can have profound effects on the functionality and reliability of fabricated MEMS devices. Residual stress often causes device failure due to curling, buckling, or fracture. Typically, the material properties of thin films used in surface micromachining are not very well controlled during deposition. The residual stress, for example, tends to vary significantly for different deposition conditions; experiments were carried out to study the polysilicon and silicon nitride deposited by Low Pressure Chemical Vapor Deposition (LPCVD) method at wide range of process conditions. High temperature annealing effects on stress in case polysilicon are also reported. The reduced residual stress levels can significantly improve device performance, reliability, and yield as MEMS devices become smaller.
- 14 April 2014
- Published by Hindawi Limited in Journal of Materials
- Vol. 2014, 1-8
Open AccessSynthesis and Characterization of LPCVD Polysilicon and Silicon Nitride Thin Films for MEMS Applications
Inherent residual stresses during material deposition can have profound effects on the functionality and reliability of fabricated MEMS devices. Residual stress often causes device failure due to curling, buckling, or fracture. Typically, the material properties of thin films used in surface micromachining are not very well controlled during deposition. The residual stress, for example, tends to vary significantly for different deposition conditions; experiments were carried out to study the polysilicon and silicon nitride deposited by Low Pressure Chemical Vapor Deposition (LPCVD) method at wide range of process conditions. High temperature annealing effects on stress in case polysilicon are also reported. The reduced residual stress levels can significantly improve device performance, reliability, and yield as MEMS devices become smaller.