Karani Kurtuluş
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Karani Kurtuluş has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Murat Varol
Akdeniz Universitesi
3 shared publications - Sema Yurdakul
Süleyman Demirel Üniversitesi
3 shared publications - Barış Gürel
Süleyman Demirel Üniversitesi, Mühendislik Fakültesi
2 shared publications - Habib Gürbüz
Süleyman Demirel Üniversitesi
2 shared publications Ali BolattÜRk
1 shared publication- Ali Keçebaş
Department of Energy Systems Engineering, Muğla Sıtkı Koçman University, Muğla, Turkey
1 shared publication
Latest Publications
- 30 June 2026
- Published by Makina Muhendisleri Odasi (Chamber of Mechanical Engineering) in Mühendis ve Makina
- Vol. 67 (723) , 289-309
Determination of Aspect Ratio and Excess Air Coefficient to Shorten Start-up Time at Small Size Fluidized Bed Boiler
Energy production from clean and renewable sources has gained prominence in recent years. The use of fluidized bed boilers in industrial applications is increasing due to their high combustion efficiency and low NOx emission. Fluidized beds are suitable for coal and biomass combustion and other gasification applications. Therefore, these systems are expected to become more widespread. Although they are widely used in industry, fluidized bed combustion systems start-up processes are generally based on experience. Start-up is an essential process in the operation of small size fluidized beds. Shorter start-up times are desired, especially in systems requiring frequent start-ups. This study investigated the effect of the height of static bed material and the coefficient of burner excess air on start-up time. Therefore, a bench-scale experimental setup was established. CFD analysis was verified with temperature data measured by the testing apparatus. Then, CFD analyses were carried out for different bed aspect ratios (0.55, 0.65, and 0.90) and different coefficients of burner excess air (1.2, 1.4, and 1.6). The analysis results show start-up time decreases (up to 32%) as the bed aspect ratio decreases. On the other hand, as the excess air coefficient increases, the start-up time increases (up to 44%). In addition, in the start-up process, excess air coefficient 1.4 and then 1.2 were proposed for a shorter start-up time with an aspect ratio of 0.9.
- 30 June 2026
- Published by Makina Muhendisleri Odasi (Chamber of Mechanical Engineering) in Mühendis ve Makina
- Vol. 67 (723) , 289-309
Determination of Aspect Ratio and Excess Air Coefficient to Shorten Start-up Time at Small Size Fluidized Bed Boiler
Energy production from clean and renewable sources has gained prominence in recent years. The use of fluidized bed boilers in industrial applications is increasing due to their high combustion efficiency and low NOx emission. Fluidized beds are suitable for coal and biomass combustion and other gasification applications. Therefore, these systems are expected to become more widespread. Although they are widely used in industry, fluidized bed combustion systems start-up processes are generally based on experience. Start-up is an essential process in the operation of small size fluidized beds. Shorter start-up times are desired, especially in systems requiring frequent start-ups. This study investigated the effect of the height of static bed material and the coefficient of burner excess air on start-up time. Therefore, a bench-scale experimental setup was established. CFD analysis was verified with temperature data measured by the testing apparatus. Then, CFD analyses were carried out for different bed aspect ratios (0.55, 0.65, and 0.90) and different coefficients of burner excess air (1.2, 1.4, and 1.6). The analysis results show start-up time decreases (up to 32%) as the bed aspect ratio decreases. On the other hand, as the excess air coefficient increases, the start-up time increases (up to 44%). In addition, in the start-up process, excess air coefficient 1.4 and then 1.2 were proposed for a shorter start-up time with an aspect ratio of 0.9.
- 2 December 2025
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 44 (19) , 1-16
Combustion and kinetic synergy of raw/torrefied chicken manure and rose pulp blended with low-grade lignite
- 2 December 2025
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 44 (19) , 1-16
Combustion and kinetic synergy of raw/torrefied chicken manure and rose pulp blended with low-grade lignite
- 28 June 2023
- Published by Elsevier in Waste Management
- Vol. 168, 423-430
PCDD/Fs, PAHs and HCl emissions from co-combustion of lignite and chicken manure in a circulating fluidized bed boiler with compact refractory casting
- 28 June 2023
- Published by Elsevier in Waste Management
- Vol. 168, 423-430
PCDD/Fs, PAHs and HCl emissions from co-combustion of lignite and chicken manure in a circulating fluidized bed boiler with compact refractory casting
- 30 December 2022
- Published by Makina Muhendisleri Odasi (Chamber of Mechanical Engineering) in Mühendis ve Makina
- Vol. 63 (709) , 689-708
Design and Experimental Investigation of Novel Flue Gas Condenser
Dünyada ihtiyaç olan enerjinin büyük kısmı halen fosil yakıtlarla sağlanmaktadır. Küresel salgın, savaşlar, doğal afetler vb. sebeplerden dolayı enerji maliyetleri her geçen gün artmaktadır. Bundan dolayı enerji verimli sistemlere rağbet artmaktadır. Bu çalışmada, doğalgaz kaynaklı bir kazanın atık baca gazı ısısı kondenserle geri kazanılmıştır. Öncelikle analitik hesaplamalar ile kondenser boyutlandırılmıştır. Daha verimli ısı geri kazanımı için gövde ve boru tarafında homojen akışkan dağılımı amaçlanmıştır ve bunun için HAD analizleri yürütülerek nihai tasarım, analiz sonuçlarına göre belirlenmiştir. Sonrasında kondenser üzerinde performans deneyleri gerçekleştirilmiş olup, analitik hesaplar ile %94 oranında doğrulanmıştır. Ayrıca nihai tasarımda gövde tarafındaki akışın homojen olduğu termal kamerayla ispatlanmıştır.
- 30 December 2022
- Published by Makina Muhendisleri Odasi (Chamber of Mechanical Engineering) in Mühendis ve Makina
- Vol. 63 (709) , 689-708
Design and Experimental Investigation of Novel Flue Gas Condenser
Dünyada ihtiyaç olan enerjinin büyük kısmı halen fosil yakıtlarla sağlanmaktadır. Küresel salgın, savaşlar, doğal afetler vb. sebeplerden dolayı enerji maliyetleri her geçen gün artmaktadır. Bundan dolayı enerji verimli sistemlere rağbet artmaktadır. Bu çalışmada, doğalgaz kaynaklı bir kazanın atık baca gazı ısısı kondenserle geri kazanılmıştır. Öncelikle analitik hesaplamalar ile kondenser boyutlandırılmıştır. Daha verimli ısı geri kazanımı için gövde ve boru tarafında homojen akışkan dağılımı amaçlanmıştır ve bunun için HAD analizleri yürütülerek nihai tasarım, analiz sonuçlarına göre belirlenmiştir. Sonrasında kondenser üzerinde performans deneyleri gerçekleştirilmiş olup, analitik hesaplar ile %94 oranında doğrulanmıştır. Ayrıca nihai tasarımda gövde tarafındaki akışın homojen olduğu termal kamerayla ispatlanmıştır.
- 4 February 2021
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (45) , 63894-63904
Investigation on thermal degradation kinetics and mechanisms of chicken manure, lignite, and their blends by TGA
In this study, thermogravimetric analysis (TGA) was performed under the air environment for four different heating rates (10, 20, 30, and 40 °C min−1) in order to find out thermal degradation and mechanisms of the chicken manure, a Turkish lignite, and their blends (25 lignite + 75 manure, 50 lignite + 50 manure, and 75 lignite + 25 manure). To calculate thermal kinetics and responsible solid-state mechanisms of the samples, the Flynn-Wall-Ozawa and Coats-Redfern methods were applied. Significant differences between Turkish lignite and chicken manure samples were observed in terms of thermal kinetics and mechanisms. D1 and D4 mechanisms were found to be the responsible mechanisms for the main oxidation region of the lignite and chicken manure/blends, respectively. A similar decreasing trend for the calculated activation energies and pre-exponential constants was observed with increasing biomass content in the manure blends from 25 to 75% by both Flynn-Wall-Ozawa and Coats-Redfern methods. Furthermore, biomass content has an effect on the mechanisms of chicken manure blends during the combustion. D3 was found to be the responsible solid-state mechanism for the third regions (pre-combustion of the manure) of the chicken manure samples. However, D1 and D2 mechanisms were found to be responsible mechanisms for the blends.
- 4 February 2021
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (45) , 63894-63904
Investigation on thermal degradation kinetics and mechanisms of chicken manure, lignite, and their blends by TGA
In this study, thermogravimetric analysis (TGA) was performed under the air environment for four different heating rates (10, 20, 30, and 40 °C min−1) in order to find out thermal degradation and mechanisms of the chicken manure, a Turkish lignite, and their blends (25 lignite + 75 manure, 50 lignite + 50 manure, and 75 lignite + 25 manure). To calculate thermal kinetics and responsible solid-state mechanisms of the samples, the Flynn-Wall-Ozawa and Coats-Redfern methods were applied. Significant differences between Turkish lignite and chicken manure samples were observed in terms of thermal kinetics and mechanisms. D1 and D4 mechanisms were found to be the responsible mechanisms for the main oxidation region of the lignite and chicken manure/blends, respectively. A similar decreasing trend for the calculated activation energies and pre-exponential constants was observed with increasing biomass content in the manure blends from 25 to 75% by both Flynn-Wall-Ozawa and Coats-Redfern methods. Furthermore, biomass content has an effect on the mechanisms of chicken manure blends during the combustion. D3 was found to be the responsible solid-state mechanism for the third regions (pre-combustion of the manure) of the chicken manure samples. However, D1 and D2 mechanisms were found to be responsible mechanisms for the blends.
- 19 August 2018
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
- Vol. 26 (6) , 3255-3261
Design of Conformal Cooling Channels Using Numerical Methods in a Metal Mold and Calculating Exergy Destruction in Channels
Shorter cycle times, better product quality and less product outage can be possible with faster cooling. But mold cooling channels can only be made in linear directions and limited forms via classical manufacturing methods. Therefore, it limits that performance of mold cooling. Developed in recent years additive manufacturing technologies are capable of building complex geometries and monoblock 3D products. With this technology it is possible to produce metal molds with conformal cooling channels in different forms and capable of qualified cooling. In this study, conformal cooling channels were designed in order to achieve optimum cooling in monoblock permanent mold. In this study, CFD (Computational Fluid Dynamic) analyses are performed to steady stead conditions for designed conformal cooling channels and classical cooling channel mold. Pressure drops, cooling channel outlet temperatures and exergy destructions are calculated depending on the flow velocity rate in channels. The numerical investigations of the cooling process have shown that approximately 5% higher cooling performance can be achieved with conformal cooling channels. However, the pressure drop in the conformal cooling is observed to be higher than classical cooling channel. In addition, exergy destruction in the conformal cooling channel is approximately 12% greater than the classical cooling channel.
- 19 August 2018
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
- Vol. 26 (6) , 3255-3261
Design of Conformal Cooling Channels Using Numerical Methods in a Metal Mold and Calculating Exergy Destruction in Channels
Shorter cycle times, better product quality and less product outage can be possible with faster cooling. But mold cooling channels can only be made in linear directions and limited forms via classical manufacturing methods. Therefore, it limits that performance of mold cooling. Developed in recent years additive manufacturing technologies are capable of building complex geometries and monoblock 3D products. With this technology it is possible to produce metal molds with conformal cooling channels in different forms and capable of qualified cooling. In this study, conformal cooling channels were designed in order to achieve optimum cooling in monoblock permanent mold. In this study, CFD (Computational Fluid Dynamic) analyses are performed to steady stead conditions for designed conformal cooling channels and classical cooling channel mold. Pressure drops, cooling channel outlet temperatures and exergy destructions are calculated depending on the flow velocity rate in channels. The numerical investigations of the cooling process have shown that approximately 5% higher cooling performance can be achieved with conformal cooling channels. However, the pressure drop in the conformal cooling is observed to be higher than classical cooling channel. In addition, exergy destruction in the conformal cooling channel is approximately 12% greater than the classical cooling channel.
- Open Access
- 1 January 2016
- Published by XMLink in The Journal of Advanced Prosthodontics
- Vol. 8 (5) , 372-379
Empirical study of alginate impression materials by customized proportioning system
Kurtulus K, et al. J Adv Prosthodont. 2016 Oct;8(5):372-379. https://doi.org/10.4047/jap.2016.8.5.372
- 1 January 2016
- Published by XMLink in The Journal of Advanced Prosthodontics
- Vol. 8 (5) , 372-379
Open AccessEmpirical study of alginate impression materials by customized proportioning system
Kurtulus K, et al. J Adv Prosthodont. 2016 Oct;8(5):372-379. https://doi.org/10.4047/jap.2016.8.5.372