Hai Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hai Huang has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Yun Chiu
Texas Analog Center of Excellence, University of Texas at Dallas, Richardson, TX, USA
3 shared publications - Hongda Xu
Texas Analog Center of Excellence, The University of Texas at Dallas, Richardson, TX 75080 USA
2 shared publications - Benwei Xu
Department of Electrical and Computer Engineering, The University of Texas at Dallas, Richardson, TX 75080 USA. He is now with Apple Inc., Cupertino, CA 95014 USA
1 shared publication Brian Elies
Texas Instruments, Dallas, TX, USA
1 shared publicationCui Linhai
Harbin University of Science and Technology, Harbin, China
1 shared publicationDatao Gong
Physics Department, Southern Methodist University, Dallas, TX 75205 USA
1 shared publication
Latest Publications
- 7 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (2) , 441-451
A 78.5-dB SNDR Radiation- and Metastability-Tolerant Two-Step Split SAR ADC Operating Up to 75 MS/s With 24.9-mW Power Consumption in 65-nm CMOS
This paper presents a 14-bit radiation- and metastability-tolerant two-step split successive-approximation register (SAR) analog-to-digital converter (ADC) that achieves a 78.5-dB peak signal-to-noise-and-distortion ratio (SNDR) and a 103-dB peak spurious-free dynamic range (SFDR) at 35 MS/s. The prototype operates up to 75 MS/s with less than 25-mW power consumption. To tolerate errors originating from radiations and/or metastability, multiple redundancy techniques are implemented hierarchically from the system level to the circuit level. At the system level, the deployment of the split architecture plus a few additional error detection techniques not only identify but also correct the errors, leading to a p to p² error rate reduction. These detection techniques include a residue over- and under (OU)-flow detection using the second-stage digital codes, an extra bit (EB)-cycle error detection with LSB repeating using a larger digital-to-analog converter (DAC) capacitor, and a parity bit (PB) error detection for on-the-fly SAR data latch protection. Sub-radix-2 DAC and reference voltage scaling also create circuit-level intra- and inter-stage redundancy, further improving the robustness of the conversion process. Preamplifier sharing and offset digital calibration alleviate the offset problem between the residue amplifier (RA) and the first-stage comparator. Two reference buffers are implemented on chip with a 1.8-V supply. Fabricated in a 65-nm CMOS process, the ADC core occupies an active area of 0.342 mm².
- 7 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (2) , 441-451
A 78.5-dB SNDR Radiation- and Metastability-Tolerant Two-Step Split SAR ADC Operating Up to 75 MS/s With 24.9-mW Power Consumption in 65-nm CMOS
This paper presents a 14-bit radiation- and metastability-tolerant two-step split successive-approximation register (SAR) analog-to-digital converter (ADC) that achieves a 78.5-dB peak signal-to-noise-and-distortion ratio (SNDR) and a 103-dB peak spurious-free dynamic range (SFDR) at 35 MS/s. The prototype operates up to 75 MS/s with less than 25-mW power consumption. To tolerate errors originating from radiations and/or metastability, multiple redundancy techniques are implemented hierarchically from the system level to the circuit level. At the system level, the deployment of the split architecture plus a few additional error detection techniques not only identify but also correct the errors, leading to a p to p² error rate reduction. These detection techniques include a residue over- and under (OU)-flow detection using the second-stage digital codes, an extra bit (EB)-cycle error detection with LSB repeating using a larger digital-to-analog converter (DAC) capacitor, and a parity bit (PB) error detection for on-the-fly SAR data latch protection. Sub-radix-2 DAC and reference voltage scaling also create circuit-level intra- and inter-stage redundancy, further improving the robustness of the conversion process. Preamplifier sharing and offset digital calibration alleviate the offset problem between the residue amplifier (RA) and the first-stage comparator. Two reference buffers are implemented on chip with a 1.8-V supply. Fabricated in a 65-nm CMOS process, the ADC core occupies an active area of 0.342 mm².
- 24 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 52 (12) , 3235-3247
A Non-Interleaved 12-b 330-MS/s Pipelined-SAR ADC With PVT-Stabilized Dynamic Amplifier Achieving Sub-1-dB SNDR Variation
A process, voltage, and temperature (PVT)-stabilized dynamic amplification technique is reported for the pipelined-successive-approximation-register (SAR) analog-to-digital converter (ADC). A non-interleaved 12-b 330-MS/s pipelined-SAR ADC prototype employing such technique achieves 0.5- and 0.8-dB signal-to-noise plus distortion ratio (SNDR) variations for supply voltage varying from 1.25 to 1.35 V and temperature varying from −5 °C to 85 °C, respectively. The corresponding residue gain variations are 1.5% and 1.2% under the same conditions, respectively. Moreover, 2-b/cycle SAR architecture together with the attenuated passive residue transfer technique is employed to boost the prototype conversion throughput significantly. Noise analyses of the attenuated passive residue transfer process and of the PVT stabilization circuit are also furnished. At 330 MS/s, the 65-nm CMOS prototype achieves an SNDR of 63.5 dB and a Walden FoM of 15.4 fJ/conversion step for a near-Nyquist input.
- 24 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 52 (12) , 3235-3247
A Non-Interleaved 12-b 330-MS/s Pipelined-SAR ADC With PVT-Stabilized Dynamic Amplifier Achieving Sub-1-dB SNDR Variation
A process, voltage, and temperature (PVT)-stabilized dynamic amplification technique is reported for the pipelined-successive-approximation-register (SAR) analog-to-digital converter (ADC). A non-interleaved 12-b 330-MS/s pipelined-SAR ADC prototype employing such technique achieves 0.5- and 0.8-dB signal-to-noise plus distortion ratio (SNDR) variations for supply voltage varying from 1.25 to 1.35 V and temperature varying from −5 °C to 85 °C, respectively. The corresponding residue gain variations are 1.5% and 1.2% under the same conditions, respectively. Moreover, 2-b/cycle SAR architecture together with the attenuated passive residue transfer technique is employed to boost the prototype conversion throughput significantly. Noise analyses of the attenuated passive residue transfer process and of the PVT stabilization circuit are also furnished. At 330 MS/s, the 65-nm CMOS prototype achieves an SNDR of 63.5 dB and a Walden FoM of 15.4 fJ/conversion step for a near-Nyquist input.
- 7 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 52 (6) , 1551-1562
A 1.2-GS/s 8-bit Two-Step SAR ADC in 65-nm CMOS With Passive Residue Transfer
A high-speed 2b-1b/cycle two-step successive-approximation-register analog-to-digital converter (ADC) exploiting the passive residue transfer technique is reported. The removal of the residue amplifier results in savings in the time and power consumed by the residue transfer process. The kT/C noise and potential bandwidth mismatch associated with the passive residue transfer are analyzed and also verified by circuit simulations. The use of the 2b-1b/cycle hybrid conversion scheme with an appropriate resolution partition further enhances the conversion speed. Fabricated in a 65-nm CMOS process, the prototype ADC measured a signal-to-noise plus distortion ratio of 43.7 dB and a spurious-free dynamic range of 58.1 dB for a near-Nyquist input. The total power consumption of the ADC is 5 mW and the achieved figure of merit is 35 fJ/conversion-step, all measured at a sample rate of 1.2 GS/s.
- 7 April 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 52 (6) , 1551-1562
A 1.2-GS/s 8-bit Two-Step SAR ADC in 65-nm CMOS With Passive Residue Transfer
A high-speed 2b-1b/cycle two-step successive-approximation-register analog-to-digital converter (ADC) exploiting the passive residue transfer technique is reported. The removal of the residue amplifier results in savings in the time and power consumed by the residue transfer process. The kT/C noise and potential bandwidth mismatch associated with the passive residue transfer are analyzed and also verified by circuit simulations. The use of the 2b-1b/cycle hybrid conversion scheme with an appropriate resolution partition further enhances the conversion speed. Fabricated in a 65-nm CMOS process, the prototype ADC measured a signal-to-noise plus distortion ratio of 43.7 dB and a spurious-free dynamic range of 58.1 dB for a near-Nyquist input. The total power consumption of the ADC is 5 mW and the achieved figure of merit is 35 fJ/conversion-step, all measured at a sample rate of 1.2 GS/s.
- 1 July 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 48-51
Design of a CMOS Three-Stage Operational Amplifier for ALD
In this paper, a three-stage operational amplifier with low-power consumption for ALD has been designed. Based on TSMC 0.55μm CMOS process, using HSPICE 2008 software for circuit simulation, the results showed that the proposed op-amp has more than 100dB open loop gain, meanwhile the static power consumption is less than 900μw. The circuit's phase margin is 103degrees, CMRR is 51dB and power supply rejection ratio is 57dB.
- 1 July 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 48-51
Design of a CMOS Three-Stage Operational Amplifier for ALD
In this paper, a three-stage operational amplifier with low-power consumption for ALD has been designed. Based on TSMC 0.55μm CMOS process, using HSPICE 2008 software for circuit simulation, the results showed that the proposed op-amp has more than 100dB open loop gain, meanwhile the static power consumption is less than 900μw. The circuit's phase margin is 103degrees, CMRR is 51dB and power supply rejection ratio is 57dB.