JVJose A. Villarejo

Jose A. Villarejo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jose A. Villarejo has a total of 50 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Controlador electrónico para motores BLDC empleados en automoción

    by Pedro Ángel Buendía-Rivas, Javier Garrido-López, Jaime Giménez-Gallego, José Villarejo-Mañas

    Brushless direct current motors (BLDC) are increasingly used due to their high efficiency and low maintenance requirements. This work presents the design, construction and experimental validation of an electronic controller for BLDC motors intended for application in competition vehicles. The system integrates a power stage based on a full three-phase bridge composed of MOSFET transistors, switched by a DRV8353FH gate driver. An Arduino Nano ESP32 is used to measure phase current and motor shaft speed, regulate the power delivered to the motor through pulse-width modulation, and execute real-time automatic control of these variables. A cascaded control architecture is implemented, consisting of an inner current loop and an outer speed loop, using discrete PI controllers with anti-windup. Test bench experiments validate reference tracking, disturbance rejection and the feasibility of the system for lightweight automotive applications and experimental prototyping.

  • Open Access

    Voltage-Based Synchronous Rectification for a Resonant FB DC Transformer With Output-Parallel Resonant Capacitor

    by Theyllor Hentschke De Oliveira, José Antonio Fernández Álvarez, Pablo Fernandez Miaja, Josè Antonio Villarejo Mañas, Manuel Arias

    This paper proposes a synchronous rectification (SR) method for DC-DC transformers (DCX) with resonant topologies based solely on secondary-side voltage measurements. The main application of the proposed DCX is to be part of a modular solution for primary-to-secondary bus conversion in spacecraft power distribution systems. Given the component constraints of space applications, this work develops an SR circuit topology using only voltage measurements. The SR circuit uses secondary winding voltages to trigger the turn-on of the SR switches and the resonant capacitor voltage to determine the turn-off instant. A review of existing SR techniques highlights the advantages of the proposed solution, and the mathematical analysis provides an intuitive design guide. Experimental results for a 100 W DCX validate the feasibility of the proposed strategy, achieving an average reduction around 45% in converter losses under full-load conditions.

  • Open Access

    Modular Fault Tolerant DC/DC Transformer Enabled by Natural Power Sharing

    by Abraham López, Theyllor H. Oliveira, Manuel Arias, Pablo Fernández Miaja, José A. Villarejo, Arturo Fernández

    The use of a DC/DC Transformer (DCX), composed of low-power individual modules with automatic voltage and power sharing will be presented as a possible solution to increase the input voltage and output power ranges of DCX systems. The input voltage range will be increased through just Input Series – Output Parallel (ISOP) connection and the increased power handling capability will be achieved by Input Parallel – Output Parallel (IPOP) connection. With these modules, it is possible to achieve natural power and voltage sharing using only a common synchronization signal between modules. Thanks to this natural equalization, ISOP and IPOP concepts are extended to form a DCX with a matrix structure which will be tolerant to the loss of one module without compromising the power handling capabilities. The proposed topology is analyzed in detail, including the mechanisms that can affect the distribution of voltages and currents. A reliability analysis and the response of the modular system under a failure situation have also been included. The validation of this proposal has been carried out using a modular prototype for an input voltage and an output voltage of 56 V and 28 V respectively, for a rated power of 200 W, and for a switching frequency of 365 kHz.


  • Open Access

    Voltage Ripple in Three-Phase Unidirectional Resonant Converter for CHB PV Inverter Under Nonunity Power Factor Operation

    by Sergio Tárraga-Albaladejo, Angel Molina-García, Esther De Jódar, José Villarejo

    In recent years, renewables, especially photovoltaic and wind power, have undergone significant development in all fields of application. This development has been closely linked to advances in multilevel converters, being able to achieve high levels of power and efficiency using low-voltage components. Among the multilevel converters, Cascaded-H-Bridge (CHB) converters are gaining interest due to their many advantages as grid-connected PV inverters. Nevertheless, they also have some drawbacks, such as the possibility of unbalanced power injection to the grid or leakage currents. The three-phase module cascading is an interesting modular solution to overcome most of these drawbacks. Under this assumption, this paper proposes and analyzes in detail a unidirectional DC/DC stage based on a three-phase resonant converter topology under non–unity power factor operation. The proposed three-phase association operates in open loop, removing the low frequency pulsating power in the oscillator due to grid and reducing significantly conduction losses in transistors under unity power factor. For non–unity power factors, the filter capacitor sizing and effects, as well as a dynamic model are also provided. The proposed analysis is assessed and experimentally verified by a 300W scale prototype. Extensive results and discussion is also included in the paper.


  • Open Access

    Parasitic Capacitance Effects on Active Clamp Flyback Output Characteristics: Application to IPOP Connection

    by Jacinto M. Jiménez-Martínez, Esther de Jódar, José Villarejo

    Different mechanisms for balancing power between parallel connected modules have been presented in recent years. They have been broadly classified into active and passive methods. The high output impedance of topologies, including active clamp networks, suggests that they can achieve output current sharing passively when they are connected in parallel. However, some parasitic elements, such as stray capacitances and leakage inductances, have not been considered in the theoretical analyses. Moreover, these need to be taken into account when a high step-up ratio is required because they modify the behavior and output impedance of a module, which changes the current balance. This paper presents a detailed analysis of the influence of parasitic capacitances on active clamp flyback converters that were parallel connected, using the output impedance as a current self-balance method. The proposed solution to alleviate the negative effects on current balance was also studied and validated as a successful method that did not increase the complexity of the controller. Finally, the results that were obtained using an experimental prototype with two 100W modules helped to verify the theoretical results.


  • Open Access

    Active Input Current Shaper Without an Electrolytic Capacitor for Retrofit Lamps Applications

    by Diego G. Lamar, Manuel Arias, Arturo Fernandez, Jose A. Villarejo, Javier Sebastian

    The evolution of solid-state lighting technology has transformed traditional solutions in lighting. High-brightness light-emitting diodes (HB-LEDs) have become very attractive light sources due to their excellent characteristics, namely high efficiency, a long lifetime, and low maintenance. It is evident that HB-LED drivers must be durable and efficient in order to enjoy these advantages. Moreover, to replace incandescent bulbs, the ac-to-dc HB-LED driver must be simple and have low size and comply with international regulations (i.e., injecting low-frequency harmonics into the mains supply). With the last modifications regarding low-power lighting equipment (i.e., <; 25 W), the authors have traditionally focused their efforts on increasing efficiency by sacrificing sinusoidal input current, yet all their solutions obviate the suppression of the traditional electrolytic capacitor of ac-to-dc converters, highlighting that this is the price to pay for a simple and low-size solution. This paper, however, puts forward the design of a simple and low-size ac-to-dc HB-LED driver for retrofit lamps without an electrolytic capacitor in order to extend its lifetime. The solution proposed here derives from a well-known technique used in the past, the active input current shaper (AICS), but without an electrolytic capacitor in this case. If the electrolytic capacitor of an AICS is removed, then low-frequency ripple arises at its intermediate dc bus, adding some distortion in the line input current over the proper natural one of an AICS. However, this addition is slight in comparison to the proper natural distortion of AICSs. Moreover, the low-frequency ripple at the intermediate bus is not transferred to the output with the help of the rapid output dynamic response of the AICS, which prevents flicker. This paper presents a theoretical analysis that guarantees a compromise between compliance with international regulations and the use of capacitor technologies other than the electrolytic design. Finally, a 24-W experimental prototype has been built and tested to validate the theoretical results presented in this paper.


  • Portable and wireless IV-curve tracer for >5kV organic photovoltaic modules

    by Rafael García-Valverde, Samir Chaouki-Almagro, Michael Corazza, Nieves Espinosa, Markus Hösel, Roar R. Søndergaard, Mikkel Jørgensen, José A. Villarejo, Frederik C. Krebs


  • PV self-consumption in cities: Solarfighter experience

    by R. Garcia-Valverde, J. A. Teruel, J. A. Villarejo

    Small grid-tied PV systems for self-consumption and/or net-metering applications can intensively contribute to spread distributed renewable energy generation and the penetration of smart grids. Also they offer environmental benefits and savings for consumers. Unlike medium-large scale PV facilities, the integration of these small PV systems in city environments faces some specific challenges. Solarfighter is an all-in-one micro PV tracking system developed for this kind of applications. We explain here our experience, analyzing the specific needs of these applications and how they are solved in Solarfighter.

  • Zero energy grid injection strategies using comercial inverters in solar energy power generation systems

    by A. Mateo, J.A. Villarejo, J. Jimenez, E. de Jodar

    An electronic equipment reliably that allow to control the generated electric power to be below of the electric power consumption and is able to compensate the electric energy injection into the company distribution grid, complying with the legislation and that is likely to be accepted as a valid system for electricity distribution companies is proposed. This make changes in the output power of the inverters and introducing variable loads to avoid energy injection both in time intervals which inverter power output changes as in the case of power generation over consumption. Thus the electric energy power generation system is used effectively, even when restrictions for energy injection improper exists.