Priscila Lemes Rachadel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Priscila Lemes Rachadel has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Dachamir Hotza
Federal University of Santa Catarina
9 shared publications - João Carlos Diniz da Costa
The University of Queensland, FIM2Lab—Functional Interfacial Materials and Membranes Laboratory, School of Chemical Engineering, Brisbane, QLD 4072, Australia
3 shared publications - Ricardo Antonio Francisco Machado
Chemical Engineering, Federal University of Santa Catarina, Florianópolis, 88010-970, Brazil
3 shared publications Giulliani Sachinelli Garcia
Universidade Federal de Santa Catarina
2 shared publicationsJoão C. Diniz da Costa
2 shared publications- Julius Motuzas
The University of Queensland, FIM2Lab-Functional Interfacial Materials and Membranes Laboratory, School of Chemical Engineering, Brisbane, Qld 4072, Australia
2 shared publications
Latest Publications
- Open Access
Evaluation of As-Received Green Liquor Dregs and Biomass Ash Residues from a Pulp and Paper Industry as Raw Materials for Geopolymers
This study aimed to investigate the impact of as-received biomass fly ashes (BFA) and green liquor dregs obtained from a pulp and paper plant in Brazil as substitutes for metakaolin in geopolymeric formulations. The properties of this type of waste material vary widely between different industrial plants. This study refrains from subjecting the waste materials to any form of pretreatment, taking into account their organic matter and particle size heterogeneity, requiring extensive characterization to evaluate their influence on the compressive strength, apparent open porosity, and water absorption of the geopolymeric samples. The objective was to assess their potential for upcycling purposes as an alternative to energy-intensive materials, such as ordinary Portland cement (OPC) and advanced ceramics. This potential arises from the ability of alkali-activated materials (AAM) to undergo curing at ambient temperatures, coupled with the possibility of compositions primarily derived from waste materials. To improve the sustainability of the products, the amorphous content of the raw material, which is more reactive than crystalline phases, was quantified and used as the base for mixture ratios. This approach aimed to reduce the requirement for alkaline activators, which have significant environmental impacts, while also increasing the waste content in the formulation. The incorporation of waste materials into the geopolymer matrix generally led to a reduction in the compressive strength compared to the benchmark metakaolin sample (19.4 MPa) but did not present a trend. The dregs led to values of 4.1 MPa at 25 wt% and 7.1 MPa at 50 wt%, a behavior that is somewhat counterintuitive, and BFA at 10 wt% presented 5.7 MPa. Nevertheless, the apparent open porosity remained at high levels for all the samples, close to 50%, and the compressive strength of most of them was over the values obtained for the metakaolin-only samples with mixture ratios calculated from the total composition instead of the amorphous composition. The decrease in strength and the increase in porosity were attributed to the specific characteristics of the waste materials, such as their high crystallinity, presence of organic matter, heterogeneous particle composition, and size. Overall, this study provides insight into the variations in geopolymerization based on the bulk and amorphous content of the aluminosilicate sources and how the characteristics of the waste materials influence the geopolymer matrix. It also highlights how calculating mixture ratios based on the amorphous composition improves the possibility of waste valorization through alkali activation. Additionally, it suggests that BFA and dregs might be effectively utilized in applications other than OPC substitution, such as adsorption, filtration, and catalysis.
Open AccessEvaluation of As-Received Green Liquor Dregs and Biomass Ash Residues from a Pulp and Paper Industry as Raw Materials for Geopolymers
This study aimed to investigate the impact of as-received biomass fly ashes (BFA) and green liquor dregs obtained from a pulp and paper plant in Brazil as substitutes for metakaolin in geopolymeric formulations. The properties of this type of waste material vary widely between different industrial plants. This study refrains from subjecting the waste materials to any form of pretreatment, taking into account their organic matter and particle size heterogeneity, requiring extensive characterization to evaluate their influence on the compressive strength, apparent open porosity, and water absorption of the geopolymeric samples. The objective was to assess their potential for upcycling purposes as an alternative to energy-intensive materials, such as ordinary Portland cement (OPC) and advanced ceramics. This potential arises from the ability of alkali-activated materials (AAM) to undergo curing at ambient temperatures, coupled with the possibility of compositions primarily derived from waste materials. To improve the sustainability of the products, the amorphous content of the raw material, which is more reactive than crystalline phases, was quantified and used as the base for mixture ratios. This approach aimed to reduce the requirement for alkaline activators, which have significant environmental impacts, while also increasing the waste content in the formulation. The incorporation of waste materials into the geopolymer matrix generally led to a reduction in the compressive strength compared to the benchmark metakaolin sample (19.4 MPa) but did not present a trend. The dregs led to values of 4.1 MPa at 25 wt% and 7.1 MPa at 50 wt%, a behavior that is somewhat counterintuitive, and BFA at 10 wt% presented 5.7 MPa. Nevertheless, the apparent open porosity remained at high levels for all the samples, close to 50%, and the compressive strength of most of them was over the values obtained for the metakaolin-only samples with mixture ratios calculated from the total composition instead of the amorphous composition. The decrease in strength and the increase in porosity were attributed to the specific characteristics of the waste materials, such as their high crystallinity, presence of organic matter, heterogeneous particle composition, and size. Overall, this study provides insight into the variations in geopolymerization based on the bulk and amorphous content of the aluminosilicate sources and how the characteristics of the waste materials influence the geopolymer matrix. It also highlights how calculating mixture ratios based on the amorphous composition improves the possibility of waste valorization through alkali activation. Additionally, it suggests that BFA and dregs might be effectively utilized in applications other than OPC substitution, such as adsorption, filtration, and catalysis.
- 1 December 2018
- Published by Elsevier in Ceramics International
- Vol. 44 (17) , 20671-20676
Enhanced LSCF oxygen deficiency through hydrothermal synthesis
- 1 December 2018
- Published by Elsevier in Ceramics International
- Vol. 44 (17) , 20671-20676
Enhanced LSCF oxygen deficiency through hydrothermal synthesis
- Top Cited Papers
- 1 April 2018
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 38 (4) , 988-1001
Manufacturing porous ceramic materials by tape casting—A review
- 1 April 2018
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 38 (4) , 988-1001
Top Cited PapersManufacturing porous ceramic materials by tape casting—A review
- 1 December 2017
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 37 (16) , 5249-5257
A novel route for manufacturing asymmetric BSCF-based perovskite structures by a combined tape and freeze casting method
- 1 December 2017
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 37 (16) , 5249-5257
A novel route for manufacturing asymmetric BSCF-based perovskite structures by a combined tape and freeze casting method
- 1 March 2017
- Published by Elsevier in Separation and Purification Technology
- Vol. 175, 164-169
Influence of porous structures on O 2 flux of BSCF asymmetric membranes
- 1 March 2017
- Published by Elsevier in Separation and Purification Technology
- Vol. 175, 164-169
Influence of porous structures on O 2 flux of BSCF asymmetric membranes
- 1 August 2014
- Published by Elsevier in Construction and Building Materials
- Vol. 65, 191-200
The influence of TiO2 and ZnO powder mixtures on photocatalytic activity and rheological behavior of cement pastes
- 1 August 2014
- Published by Elsevier in Construction and Building Materials
- Vol. 65, 191-200
The influence of TiO2 and ZnO powder mixtures on photocatalytic activity and rheological behavior of cement pastes
- 1 March 2014
- Published by Elsevier in Journal of Membrane Science
- Vol. 454, 382-389
The effect of non-ionic porous domains on supported Ba0.5Sr0.5Co0.8Fe0.2O3−δ membranes for O2 separation
- 1 March 2014
- Published by Elsevier in Journal of Membrane Science
- Vol. 454, 382-389
The effect of non-ionic porous domains on supported Ba0.5Sr0.5Co0.8Fe0.2O3−δ membranes for O2 separation
- Open Access
- 1 January 2014
- Published by GN1 Sistemas e Publicacoes Ltd. in Química Nova
- Vol. 37 (2)
Mixed ionic-electronic conducting membranes (MIEC): composition, preparation, and performance.
This paper presents a review of different chemical compositions that are used in the production of mixed ionic-electronic conducting membranes with the perovskite structure. In these dense membranes, oxygen from the air is permeated through ionic and electronic processes, and high oxygen permeation fluxes are observed at high temperatures (800-900 ºC). Various membranes were compared for their performance and properties after being synthesized by different methods
- 1 January 2014
- Published by GN1 Sistemas e Publicacoes Ltd. in Química Nova
- Vol. 37 (2)
Open AccessMixed ionic-electronic conducting membranes (MIEC): composition, preparation, and performance.
This paper presents a review of different chemical compositions that are used in the production of mixed ionic-electronic conducting membranes with the perovskite structure. In these dense membranes, oxygen from the air is permeated through ionic and electronic processes, and high oxygen permeation fluxes are observed at high temperatures (800-900 ºC). Various membranes were compared for their performance and properties after being synthesized by different methods
- Open Access
- 22 October 2013
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 17 (1) , 242-249
Current developments of mixed conducting membranes on porous substrates
- 22 October 2013
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 17 (1) , 242-249
Open AccessCurrent developments of mixed conducting membranes on porous substrates
- Open Access
- 24 October 2012
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2012, 1-6
Development of Alternative Glass Ceramic Seal for a Planar Solid Oxide Fuel Cell
LZSA glass ceramic (LiO2-ZrO2-SiO2-Al2O3) was tested for its thermomechanical compatibility as a sealing material with a stainless steel interconnect (AISI 430) of a planar SOFC. With this purpose, the densification and crystallization behavior of LZSA were investigated initially. It was observed that the material reached maximum relative density and shrinkage, respectively 95% and 17%, at 800°C, which corresponded approximately to the crystallization temperature of the material as evidenced by DTA analysis. In the next step, LZSA tapes were cast from slurries and prepared either as LZSA laminates or LZSA-steel bilayers. The densification behavior and microstructural features of cofired LZSA laminates and LZSA-steel bilayers were analyzed at 800 and 900°C. Maximum relative density and defect-free interfaces were observed for laminates and bi-layers cofired at 800°C, whereas increased porosity and detached bi-layer were the characteristics of the samples fired at 900°C.
- 24 October 2012
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2012, 1-6
Open AccessDevelopment of Alternative Glass Ceramic Seal for a Planar Solid Oxide Fuel Cell
LZSA glass ceramic (LiO2-ZrO2-SiO2-Al2O3) was tested for its thermomechanical compatibility as a sealing material with a stainless steel interconnect (AISI 430) of a planar SOFC. With this purpose, the densification and crystallization behavior of LZSA were investigated initially. It was observed that the material reached maximum relative density and shrinkage, respectively 95% and 17%, at 800°C, which corresponded approximately to the crystallization temperature of the material as evidenced by DTA analysis. In the next step, LZSA tapes were cast from slurries and prepared either as LZSA laminates or LZSA-steel bilayers. The densification behavior and microstructural features of cofired LZSA laminates and LZSA-steel bilayers were analyzed at 800 and 900°C. Maximum relative density and defect-free interfaces were observed for laminates and bi-layers cofired at 800°C, whereas increased porosity and detached bi-layer were the characteristics of the samples fired at 900°C.