Guodong Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Guodong Li has a total of 121 co-authors. Here are the top co-authors by number of shared publications:
Kornelius Nielsch
Leibniz Institute for Solid State and Materials Research Dresden, Dresden, Germany
7 shared publicationsDavid Alberto Lara Ramos
Institute for Metallic Materials Leibniz Institute for Solid State and Materials Research Dresden Helmholtzstrasse 20 01069 Dresden Germany
4 shared publicationsGabi Schierning
Institute for Energy and Materials Processes Applied Quantum Materials, University Duisburg-Essen, Duisburg, Germany
4 shared publications- Heiko Reith
Institute for Metallic Materials, Leibniz Institute for Solid State and Materials Research Dresden, Dresden, Germany
4 shared publications - Huaizhou Zhao
Beijing National Laboratory for Condensed Matter Physics Institute of Physics Chinese Academy of Sciences Beijing China
4 shared publications Jiawei Yang
Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing, China
4 shared publications
Latest Publications
- 10 September 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (54) , 37437-37448
Highly compact and thick tellurium film deposition for thermoelectric application
A two-step pulsed electrodeposition method yields compact, continuous tellurium thick films with exceptional Seebeck coefficient and a peak power factor of 6.62 µW cm −1 K −2 .
- 10 September 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (54) , 37437-37448
Highly compact and thick tellurium film deposition for thermoelectric application
A two-step pulsed electrodeposition method yields compact, continuous tellurium thick films with exceptional Seebeck coefficient and a peak power factor of 6.62 µW cm −1 K −2 .
- 18 December 2025
- Published by IOP Publishing in Chinese Physics Letters
- Vol. 43 (2)
Determination of Anisotropic Thermoelectric Properties of Bismuth Using a Tensor Inversion Method
Conventional methods for quantifying thermoelectric anisotropy rely on precisely aligned crystals, which are time-consuming and error-prone. To address this, we propose a tensor inversion method integrating transport measurements with EBSD-derived Euler angles to determine the intrinsic tensors of as-grown bismuth crystals. This method reconstructs the full second-rank thermoelectric tensors—including electrical resistivity, thermal conductivity, and the Seebeck coefficient—by transforming transport data between the sample coordinate system (SCS) and the crystal coordinate system (CSC). The inverted tensor components of pure bismuth show excellent agreement with reported principal-axis values, validating the accuracy of this method. Moreover, the reversibility of the tensor inversion approach allows for complete visualization of the directional dependence of the thermoelectric figure of merit ( zT ), revealing its full angular and crystallographic orientation distribution for the first time. This bidirectional framework not only provides a convenient pathway for the reconstruction of intrinsic transport tensors but also enables the prediction of orientation-dependent properties, thereby offering a robust tool for analyzing anisotropic transport behavior and guiding the optimization of thermoelectric performance.
- 18 December 2025
- Published by IOP Publishing in Chinese Physics Letters
- Vol. 43 (2)
Determination of Anisotropic Thermoelectric Properties of Bismuth Using a Tensor Inversion Method
Conventional methods for quantifying thermoelectric anisotropy rely on precisely aligned crystals, which are time-consuming and error-prone. To address this, we propose a tensor inversion method integrating transport measurements with EBSD-derived Euler angles to determine the intrinsic tensors of as-grown bismuth crystals. This method reconstructs the full second-rank thermoelectric tensors—including electrical resistivity, thermal conductivity, and the Seebeck coefficient—by transforming transport data between the sample coordinate system (SCS) and the crystal coordinate system (CSC). The inverted tensor components of pure bismuth show excellent agreement with reported principal-axis values, validating the accuracy of this method. Moreover, the reversibility of the tensor inversion approach allows for complete visualization of the directional dependence of the thermoelectric figure of merit ( zT ), revealing its full angular and crystallographic orientation distribution for the first time. This bidirectional framework not only provides a convenient pathway for the reconstruction of intrinsic transport tensors but also enables the prediction of orientation-dependent properties, thereby offering a robust tool for analyzing anisotropic transport behavior and guiding the optimization of thermoelectric performance.
- 26 October 2025
- Published by Wiley in Advanced Energy Materials
- Vol. 16 (1)
In Situ Measurement of Full‐Spectrum Emissivity for Thermoelectric Materials below Room Temperature
Accurate determination of emissivity is essential for reliable thermal conductivity measurements in thermoelectric materials. Current spectroscopic techniques are restricted by limited wavelength ranges and cannot provide comprehensive characterization. This study develops a robust in situ method to measure full‐spectrum emissivity of solid‐state materials between 160 and 300 K. For Bi 2 Te 3 ‐based thermoelectric materials, emissivity values of 0.62–0.65 (N‐type) and 0.46–0.66 (P‐type) are obtained, with precision of 4%. Validation experiments using standard quartz samples with and without gold coating, and P‐type (Bi,Sb) 2 Te 3 samples with different roughness demonstrate critical influence of surface conditions on emissivity. Importantly, measurements of thermal conductivity and emissivity of the same Bi 2 Te 3 sample under identical condition show that ignoring radiative correction leads to a dramatic 40% overestimation of thermal conductivity at 300 K. This work provides a practical method for precise emissivity characterization that enables more accurate thermoelectric material evaluation.
- 26 October 2025
- Published by Wiley in Advanced Energy Materials
- Vol. 16 (1)
In Situ Measurement of Full‐Spectrum Emissivity for Thermoelectric Materials below Room Temperature
Accurate determination of emissivity is essential for reliable thermal conductivity measurements in thermoelectric materials. Current spectroscopic techniques are restricted by limited wavelength ranges and cannot provide comprehensive characterization. This study develops a robust in situ method to measure full‐spectrum emissivity of solid‐state materials between 160 and 300 K. For Bi 2 Te 3 ‐based thermoelectric materials, emissivity values of 0.62–0.65 (N‐type) and 0.46–0.66 (P‐type) are obtained, with precision of 4%. Validation experiments using standard quartz samples with and without gold coating, and P‐type (Bi,Sb) 2 Te 3 samples with different roughness demonstrate critical influence of surface conditions on emissivity. Importantly, measurements of thermal conductivity and emissivity of the same Bi 2 Te 3 sample under identical condition show that ignoring radiative correction leads to a dramatic 40% overestimation of thermal conductivity at 300 K. This work provides a practical method for precise emissivity characterization that enables more accurate thermoelectric material evaluation.
- Open Access
- 14 April 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-12
Bulk Bi-Sb polycrystals underpinned by high electron/phonon mean free path ratio enabling thermoelectric cooling under 77 K
Bi-Sb alloy, as a promising thermoelectric material at cryogenic temperatures, has seen stagnant progress due to challenges in understanding the transport behaviors of energy carriers, and difficulties in synthesizing high-homogeneity, large-grain samples. In this study, an inherent electron-phonon decoupling in Bi-Sb is revealed using the first-principles calculations based on the virtual crystal approximation. The mean free path of the dominant electrons (λele ~ 103 nm) is found of two orders of magnitude larger than that of phonons (λph ~ 101 nm), suggesting that a grain size greater than 10 μm would be favorable for thermoelectric transport. Bulk Bi-Sb polycrystals with highly elemental homogeneity and large grain size (~80 μm) are successfully synthesized through an ultra-fast quenching method combined with annealing, delivering superior thermoelectric performance. A prototype module based on the Bi0.88Sb0.12 polycrystal, with a ZTmax of 0.48 at 150 K, is fabricated and demonstrates a ΔTmax of 4 K at a Th of 75 K. This marks the first report of n-p paired thermoelectric cooling modules operating below liquid nitrogen temperature.
- 14 April 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-12
Open AccessBulk Bi-Sb polycrystals underpinned by high electron/phonon mean free path ratio enabling thermoelectric cooling under 77 K
Bi-Sb alloy, as a promising thermoelectric material at cryogenic temperatures, has seen stagnant progress due to challenges in understanding the transport behaviors of energy carriers, and difficulties in synthesizing high-homogeneity, large-grain samples. In this study, an inherent electron-phonon decoupling in Bi-Sb is revealed using the first-principles calculations based on the virtual crystal approximation. The mean free path of the dominant electrons (λele ~ 103 nm) is found of two orders of magnitude larger than that of phonons (λph ~ 101 nm), suggesting that a grain size greater than 10 μm would be favorable for thermoelectric transport. Bulk Bi-Sb polycrystals with highly elemental homogeneity and large grain size (~80 μm) are successfully synthesized through an ultra-fast quenching method combined with annealing, delivering superior thermoelectric performance. A prototype module based on the Bi0.88Sb0.12 polycrystal, with a ZTmax of 0.48 at 150 K, is fabricated and demonstrates a ΔTmax of 4 K at a Th of 75 K. This marks the first report of n-p paired thermoelectric cooling modules operating below liquid nitrogen temperature.
- Top Cited PapersOpen Access
- 15 August 2023
- Published by Springer Nature in Nature Communications
- Vol. 14 (1) , 1-9
Improved figure of merit (z) at low temperatures for superior thermoelectric cooling in Mg3(Bi,Sb)2
The low-temperature thermoelectric performance of Bi-rich n-type Mg3(Bi,Sb)2 was limited by the electron transport scattering at grain boundaries, while removing grain boundaries and bulk crystal growth of Mg-based Zintl phases are challenging due to the volatilities of elemental reactants and their severe corrosions to crucibles at elevated temperatures. Herein, for the first time, we reported a facile growth of coarse-grained Mg3Bi2-xSbx crystals with an average grain size of ~800 μm, leading to a high carrier mobility of 210 cm2 · V−1 · s−1 and a high z of 2.9 × 10−3 K−1 at 300 K. A $$\Delta$$ T of 68 K at Th of 300 K, and a power generation efficiency of 5.8% below 450 K have been demonstrated for Mg3Bi1.5Sb0.5- and Mg3Bi1.25Sb0.75-based thermoelectric modules, respectively, which represent the cutting-edge advances in the near-room temperature thermoelectrics. In addition, the developed grain growth approach can be potentially extended to broad Zintl phases and other Mg-based alloys and compounds.- 15 August 2023
- Published by Springer Nature in Nature Communications
- Vol. 14 (1) , 1-9
Top Cited PapersOpen AccessImproved figure of merit (z) at low temperatures for superior thermoelectric cooling in Mg3(Bi,Sb)2
The low-temperature thermoelectric performance of Bi-rich n-type Mg3(Bi,Sb)2 was limited by the electron transport scattering at grain boundaries, while removing grain boundaries and bulk crystal growth of Mg-based Zintl phases are challenging due to the volatilities of elemental reactants and their severe corrosions to crucibles at elevated temperatures. Herein, for the first time, we reported a facile growth of coarse-grained Mg3Bi2-xSbx crystals with an average grain size of ~800 μm, leading to a high carrier mobility of 210 cm2 · V−1 · s−1 and a high z of 2.9 × 10−3 K−1 at 300 K. A $$\Delta$$ T of 68 K at Th of 300 K, and a power generation efficiency of 5.8% below 450 K have been demonstrated for Mg3Bi1.5Sb0.5- and Mg3Bi1.25Sb0.75-based thermoelectric modules, respectively, which represent the cutting-edge advances in the near-room temperature thermoelectrics. In addition, the developed grain growth approach can be potentially extended to broad Zintl phases and other Mg-based alloys and compounds. - Open Access
- 2 August 2023
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 16 (10) , 4693
Correction: Scalable manufacturing of a durable, tailorable, and recyclable multifunctional woven thermoelectric textile system
Correction for ‘Scalable manufacturing of a durable, tailorable, and recyclable multifunctional woven thermoelectric textile system’ by Yuanyuan Jing et al. , Energy Environ. Sci. , 2023, https://doi.org/10.1039/d3ee01031g.
- 2 August 2023
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 16 (10) , 4693
Open AccessCorrection: Scalable manufacturing of a durable, tailorable, and recyclable multifunctional woven thermoelectric textile system
Correction for ‘Scalable manufacturing of a durable, tailorable, and recyclable multifunctional woven thermoelectric textile system’ by Yuanyuan Jing et al. , Energy Environ. Sci. , 2023, https://doi.org/10.1039/d3ee01031g.
- 3 March 2022
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 15 (6) , 2374-2385
Durable, stretchable and washable inorganic-based woven thermoelectric textiles for power generation and solid-state cooling
Wearable inorganic semiconductor (ISC) based thermoelectric (TE) devices, especially fiber-based thermoelectric textiles (TETs), show promise in electrical power generation and solid-state cooling compared with bulk ISC-based TE generators (TEGs). However, it is challenging to use the ISCs, with brittleness and mechanical instability, to produce thermoelectric fibers for weaving TETs. Here, we report a strategy to produce ISC-based segmented hierarchically ternary coaxial TE strings at large scale for semi-automatically manufacturing a highly mechanically stable, stretchable, breathable and washable woven TET by a textile machine. The TET demonstrates good stretchability (100% elongation), flexibility (bending radius of 2 mm), washability (>20 washing cycles) and output power density of 0.58 W m−2 at a temperature difference of 25 K (predicted power density of 6.06 W m−2 at ΔT = 80 K). With the assistance of finite element analysis, the significance of the fabric’s structure on the excellent mechanical and TE performance of the TET has been clarified, which reaches an output voltage of ∼0.28 V at an ambient temperature of ∼8 °C. For practical applications, it can continuously power on-body electronics for monitoring the environment and the human body’s vital signals and activities by wearing it on the arm with a self-built temperature gradient of ∼16 K. Furthermore, the TET can stably generate solid-state cooling of 3.1 K in quiescent air (Tambient ∼ 26 °C, relative humidity ∼60%). This work paves a new way for designing durable, stretchable and washable ISC-based TETs toward real on-body applications.
- 3 March 2022
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 15 (6) , 2374-2385
Durable, stretchable and washable inorganic-based woven thermoelectric textiles for power generation and solid-state cooling
Wearable inorganic semiconductor (ISC) based thermoelectric (TE) devices, especially fiber-based thermoelectric textiles (TETs), show promise in electrical power generation and solid-state cooling compared with bulk ISC-based TE generators (TEGs). However, it is challenging to use the ISCs, with brittleness and mechanical instability, to produce thermoelectric fibers for weaving TETs. Here, we report a strategy to produce ISC-based segmented hierarchically ternary coaxial TE strings at large scale for semi-automatically manufacturing a highly mechanically stable, stretchable, breathable and washable woven TET by a textile machine. The TET demonstrates good stretchability (100% elongation), flexibility (bending radius of 2 mm), washability (>20 washing cycles) and output power density of 0.58 W m−2 at a temperature difference of 25 K (predicted power density of 6.06 W m−2 at ΔT = 80 K). With the assistance of finite element analysis, the significance of the fabric’s structure on the excellent mechanical and TE performance of the TET has been clarified, which reaches an output voltage of ∼0.28 V at an ambient temperature of ∼8 °C. For practical applications, it can continuously power on-body electronics for monitoring the environment and the human body’s vital signals and activities by wearing it on the arm with a self-built temperature gradient of ∼16 K. Furthermore, the TET can stably generate solid-state cooling of 3.1 K in quiescent air (Tambient ∼ 26 °C, relative humidity ∼60%). This work paves a new way for designing durable, stretchable and washable ISC-based TETs toward real on-body applications.
- Open Access
- 12 February 2022
- Published by Wiley in Advanced Electronic Materials
- Vol. 8 (7) , 2101042
Geometric Study of Polymer Embedded Micro Thermoelectric Cooler with Optimized Contact Resistance
Micro‐thermoelectric devices (μTEDs) are used for bio‐medical applications, powering internet‐of‐things devices, and thermal management. For such applications, μTEDs need to have a robust packaging so that the devices can be brought in direct thermal contact with the target heat sink and source. The packaging technology developed for macroscopic modules needs improvement as it cannot be applied to μTEDs due to a large thermal resistance between the capping material and the device which deteriorates its performance. In this work, μTEDs with high net cooling temperature are fabricated by optimizing the contact resistance and device design combined with a novel packaging technique that is fully compatible with on‐chip integration. The simulations and experiments demonstrate that the additional thermal loss caused by the packaging leads to an only marginal decrease in the net cooling temperature. The devices achieve a high net cooling temperature of 10.8 K without packaging and 9.6 K with packaging at room temperature. The packaging only slightly increases the thermal response time of the devices, which also shows an extremely high reliability of over 85 million cooling cycles. This simple packaging technique together with robust device performance is a step toward wide‐spread application of μTEDs.
- 12 February 2022
- Published by Wiley in Advanced Electronic Materials
- Vol. 8 (7) , 2101042
Open AccessGeometric Study of Polymer Embedded Micro Thermoelectric Cooler with Optimized Contact Resistance
Micro‐thermoelectric devices (μTEDs) are used for bio‐medical applications, powering internet‐of‐things devices, and thermal management. For such applications, μTEDs need to have a robust packaging so that the devices can be brought in direct thermal contact with the target heat sink and source. The packaging technology developed for macroscopic modules needs improvement as it cannot be applied to μTEDs due to a large thermal resistance between the capping material and the device which deteriorates its performance. In this work, μTEDs with high net cooling temperature are fabricated by optimizing the contact resistance and device design combined with a novel packaging technique that is fully compatible with on‐chip integration. The simulations and experiments demonstrate that the additional thermal loss caused by the packaging leads to an only marginal decrease in the net cooling temperature. The devices achieve a high net cooling temperature of 10.8 K without packaging and 9.6 K with packaging at room temperature. The packaging only slightly increases the thermal response time of the devices, which also shows an extremely high reliability of over 85 million cooling cycles. This simple packaging technique together with robust device performance is a step toward wide‐spread application of μTEDs.
- Open Access
- 13 December 2021
- Published by American Physical Society (APS) in Physical Review Research
- Vol. 3 (4) , 043178
Emergence of 1/3 magnetization plateau and successive magnetic transitions in Zintl phaseSingle crystals of have been successfully synthesized by indium flux reactions. crystallizes in the -type structure with an orthorhombic space-group . Theoretical calculations indicate that is a semiconductor with a direct band gap of 0.3 eV. has large negative Seebeck coefficients in the range of 300–450 μV/K at room temperature. displays two antiferromagnetic transitions ( and K) for both and which can be suppressed by magnetic fields. At 2 K, field-induced ferromagnetic states are reached for both and . Particularly, the magnetization curves show a plateau at 1/3 of the saturated magnetization and an anomaly at 2/3 of the saturated magnetization. is a Zintl phase material showing a 1/3 magnetization plateau here.- 13 December 2021
- Published by American Physical Society (APS) in Physical Review Research
- Vol. 3 (4) , 043178
Open AccessEmergence of 1/3 magnetization plateau and successive magnetic transitions in Zintl phaseSingle crystals of have been successfully synthesized by indium flux reactions. crystallizes in the -type structure with an orthorhombic space-group . Theoretical calculations indicate that is a semiconductor with a direct band gap of 0.3 eV. has large negative Seebeck coefficients in the range of 300–450 μV/K at room temperature. displays two antiferromagnetic transitions ( and K) for both and which can be suppressed by magnetic fields. At 2 K, field-induced ferromagnetic states are reached for both and . Particularly, the magnetization curves show a plateau at 1/3 of the saturated magnetization and an anomaly at 2/3 of the saturated magnetization. is a Zintl phase material showing a 1/3 magnetization plateau here.