Dongsheng Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dongsheng Xu has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
Rui Yang
11 shared publicationsJinhu Zhang
Institute of Metal Research, Chinese Academy of Sciences, Shenyang, P.R. China
6 shared publicationsHao Wang
5 shared publicationsXuexiong Li
Institute of Metal Research, Chinese Academy of Sciences, Shenyang, P.R. China
4 shared publications- Hao Wang
Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China
3 shared publications Hui Guo
3 shared publications
Latest Publications
- Open Access
Effect of Hatch Spacing on Microstructure, Defect Formation and Properties of Additively Manufactured A7075 Alloy
Understanding the mechanisms of microstructure evolution and defect formation, and their influence on mechanical properties and fracture mechanisms (from crack initiation to failure stage), is essential for manufacturing high-strength, fatigue-resistant A7075 alloy by selective laser melting (SLM). In this investigation, the A7075 alloy was fabricated using a laser power of 350 W with various hatch spacings of 1.0, 1.5, and 2.0 μm, and scanning speeds of 800, 1100, and 1300 mm/s. The results show that the alloy exhibits an equiaxed grain structure, which varies from coarse grains at small hatch spacing and low scanning speed to fine grains with increasing hatch spacing and scanning speed. The alloys exhibit low tensile strength due to solidification cracking and pores. However, this tensile strength increases with hatch spacing, while it decreases with scanning speed. At small hatch spacing and low scanning speed, fracture occurs through the coalescence of pores and solidification cracking along the weakly bonded grain boundaries (GBs) due to eutectic growth along these boundaries. In contrast, with increasing hatch spacing and scanning speed, fracture occurs through solidification cracking and coalescence of pores. This research provides valuable insights into the microstructure evolution, defect formation, and fracture mechanisms of the A7075 alloy under common processing conditions.
Open AccessEffect of Hatch Spacing on Microstructure, Defect Formation and Properties of Additively Manufactured A7075 Alloy
Understanding the mechanisms of microstructure evolution and defect formation, and their influence on mechanical properties and fracture mechanisms (from crack initiation to failure stage), is essential for manufacturing high-strength, fatigue-resistant A7075 alloy by selective laser melting (SLM). In this investigation, the A7075 alloy was fabricated using a laser power of 350 W with various hatch spacings of 1.0, 1.5, and 2.0 μm, and scanning speeds of 800, 1100, and 1300 mm/s. The results show that the alloy exhibits an equiaxed grain structure, which varies from coarse grains at small hatch spacing and low scanning speed to fine grains with increasing hatch spacing and scanning speed. The alloys exhibit low tensile strength due to solidification cracking and pores. However, this tensile strength increases with hatch spacing, while it decreases with scanning speed. At small hatch spacing and low scanning speed, fracture occurs through the coalescence of pores and solidification cracking along the weakly bonded grain boundaries (GBs) due to eutectic growth along these boundaries. In contrast, with increasing hatch spacing and scanning speed, fracture occurs through solidification cracking and coalescence of pores. This research provides valuable insights into the microstructure evolution, defect formation, and fracture mechanisms of the A7075 alloy under common processing conditions.
- Open Access
Slip Irreversibility, Microplasticity, and Fatigue Cracking Mechanism in Near-α and α + β Titanium Alloys
The micromechanisms “slip transfer, slip irreversibility, microplasticity, and fatigue cracking” in titanium alloys are reviewed, with a special emphasis on near-α and α + β alloys. As the interplay between slip activity, microplasticity, and fatigue cracking governs both the microscale and macroscale mechanical response, we reveal how the slip irreversibility and localized dislocation activity at the grain boundaries (GBs) and α/β interfaces generate dislocation pile-ups and strain localization, subsequently driving fatigue crack initiation and propagation. The review highlights the favorable crack initiation along basal planes and the roles of α grain orientations, slip transfer barriers, and the β phase in governing fatigue cracking, while addressing unresolved questions about localized interactions and texture effects. It also explores the complex interactions that govern the effects of microstructures, textures, and defects on fatigue cracking. Ultimately, the review provides a unified framework for linking slip events to microplasticity and to fatigue failure, offering actionable insights for alloy design and fatigue prediction.
Open AccessSlip Irreversibility, Microplasticity, and Fatigue Cracking Mechanism in Near-α and α + β Titanium Alloys
The micromechanisms “slip transfer, slip irreversibility, microplasticity, and fatigue cracking” in titanium alloys are reviewed, with a special emphasis on near-α and α + β alloys. As the interplay between slip activity, microplasticity, and fatigue cracking governs both the microscale and macroscale mechanical response, we reveal how the slip irreversibility and localized dislocation activity at the grain boundaries (GBs) and α/β interfaces generate dislocation pile-ups and strain localization, subsequently driving fatigue crack initiation and propagation. The review highlights the favorable crack initiation along basal planes and the roles of α grain orientations, slip transfer barriers, and the β phase in governing fatigue cracking, while addressing unresolved questions about localized interactions and texture effects. It also explores the complex interactions that govern the effects of microstructures, textures, and defects on fatigue cracking. Ultimately, the review provides a unified framework for linking slip events to microplasticity and to fatigue failure, offering actionable insights for alloy design and fatigue prediction.
- 22 December 2025
- Published by Elsevier in International Journal of Plasticity
- Vol. 197
Strain rate-driven transition between dislocation slip and twinning in Ti-6Al-4V ELI alloy during tensile deformation
- 22 December 2025
- Published by Elsevier in International Journal of Plasticity
- Vol. 197
Strain rate-driven transition between dislocation slip and twinning in Ti-6Al-4V ELI alloy during tensile deformation
- 18 April 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (6) , 1971-1982
Molecular Dynamics Simulation of the Atomic Mechanisms of Deformation and Phase Transformation in Titanium Alloys
- 18 April 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (6) , 1971-1982
Molecular Dynamics Simulation of the Atomic Mechanisms of Deformation and Phase Transformation in Titanium Alloys
- 16 November 2024
- Published by Elsevier in Computational Materials Science
- Vol. 247
Crystal plasticity study on deformation behavior of dual-phase Ti alloy under biaxial loading conditions
- 16 November 2024
- Published by Elsevier in Computational Materials Science
- Vol. 247
Crystal plasticity study on deformation behavior of dual-phase Ti alloy under biaxial loading conditions
- Open Access
- 24 October 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 6319-6327
Effect of texture on the fatigue crack initiation of a Dual-Phase Titanium alloy
- 24 October 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 6319-6327
Open AccessEffect of texture on the fatigue crack initiation of a Dual-Phase Titanium alloy
- Open Access
- 10 November 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 27, 6833-6846
Effect of texture on the mechanical and micromechanical properties of a dual-phase titanium alloy
- 10 November 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 27, 6833-6846
Open AccessEffect of texture on the mechanical and micromechanical properties of a dual-phase titanium alloy
- Open Access
- 22 October 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 27, 4562-4572
Effect of common alloying elements on α’ martensite start temperature in titanium alloys
- 22 October 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 27, 4562-4572
Open AccessEffect of common alloying elements on α’ martensite start temperature in titanium alloys
- 20 September 2023
- Published by Elsevier in Acta Materialia
- Vol. 261
Dislocation-mediated migration of the α/β interfaces in titanium
- 20 September 2023
- Published by Elsevier in Acta Materialia
- Vol. 261
Dislocation-mediated migration of the α/β interfaces in titanium
- Open Access
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Refinement of Α′ Martensite by Oxygen in Selective Laser Melted Ti-6al-4v
The α′ martensitic transformation in Ti-6Al-4V and the mechanisms of martensite refinement by oxygen have been investigated using Ti-6Al-4V-xO (x=0.11, 0.16, 0.21, and 0.25 wt.%) alloys fabricated by selective laser melting process. The martensite start temperature Ms of Ti-6Al-4V is evaluated to be 656.8 oC and oxygen was found to increase the Ms by about 10 oC per 0.1 wt.% of oxygen. The [001] β growth texture along the build direction allows crystallographic analysis of martensite morphology suggesting internal twinning on [[EQUATION]] planes as the lattice invariant strain mechanism which becomes more predominant with increasing oxygen content. Refinement of martensite plates by oxygen is due to increased lattice distortion as well as reduced prior β grain size as a result of oxygen addition.
- 1 January 2023
- Published by Elsevier in SSRN Electronic Journal
Open AccessRefinement of Α′ Martensite by Oxygen in Selective Laser Melted Ti-6al-4v
The α′ martensitic transformation in Ti-6Al-4V and the mechanisms of martensite refinement by oxygen have been investigated using Ti-6Al-4V-xO (x=0.11, 0.16, 0.21, and 0.25 wt.%) alloys fabricated by selective laser melting process. The martensite start temperature Ms of Ti-6Al-4V is evaluated to be 656.8 oC and oxygen was found to increase the Ms by about 10 oC per 0.1 wt.% of oxygen. The [001] β growth texture along the build direction allows crystallographic analysis of martensite morphology suggesting internal twinning on [[EQUATION]] planes as the lattice invariant strain mechanism which becomes more predominant with increasing oxygen content. Refinement of martensite plates by oxygen is due to increased lattice distortion as well as reduced prior β grain size as a result of oxygen addition.