Roberto Sangines
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Roberto Sangines has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Hugo Sobral
Instituto de Ciencias Aplicadas y Tecnología, Universidad Nacional Autónoma de México, Circuito Exterior S/N, Ciudad Universitaria, Mexico City 04510, Mexico
14 shared publications - Marcela Milena Marie Bilek
The University of Sydney
5 shared publications - David Robert McKenzie
The University of Sydney
4 shared publications - Juan Aguila-Muñoz
Autonomous University of Tlaxcala
4 shared publications - Noemí Abundiz-Cisneros
Universidad Nacional Autónoma de México
4 shared publications C. Sánchez Aké
3 shared publications
Latest Publications
- 19 May 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (20) , 205203
Optimization of deposition parameters for silicon dioxide thin films synthesized by reactive pulsed-direct current magnetron sputtering
Silicon dioxide (SiO₂) thin films were deposited by pulsed DC reactive magnetron sputtering under conditions in which discharge power and pulse frequency were systematically varied. Optical emission spectroscopy, voltage–current waveform analysis, and spectroscopic ellipsometry were combined to correlate the experimental parameters with the refractive index, extinction coefficient, and deposition rate of the films. The study shows that SiO₂ films with desirable optical characteristics can be obtained when the deposition is carried out at the optimal point identified in the characterization curves, where the transition into the poisoned regime is properly established. The integrated methodology provides a framework for optimizing pulsed-DC reactive sputtering processes and can be extended to the controlled synthesis of other compound films.
- 19 May 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (20) , 205203
Optimization of deposition parameters for silicon dioxide thin films synthesized by reactive pulsed-direct current magnetron sputtering
Silicon dioxide (SiO₂) thin films were deposited by pulsed DC reactive magnetron sputtering under conditions in which discharge power and pulse frequency were systematically varied. Optical emission spectroscopy, voltage–current waveform analysis, and spectroscopic ellipsometry were combined to correlate the experimental parameters with the refractive index, extinction coefficient, and deposition rate of the films. The study shows that SiO₂ films with desirable optical characteristics can be obtained when the deposition is carried out at the optimal point identified in the characterization curves, where the transition into the poisoned regime is properly established. The integrated methodology provides a framework for optimizing pulsed-DC reactive sputtering processes and can be extended to the controlled synthesis of other compound films.
- Open Access
- 4 March 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 35 (3)
Experimentally informed modelling of argon dielectric barrier discharge
Low-pressure (1.3 Torr) plasma breakdown in an asymmetric argon DBD with a 10 mm gap was investigated both numerically and experimentally. A one-dimensional fluid model was validated against the experimentally obtained optical emission spectroscopy (OES) spectra, high-speed imaging and plasma current measurements. The model predicts distinct spatio-temporal oscillations in charged particle densities preceding breakdown, these are confirmed experimentally. OES analysis supports a Druyvesteyn form of the electron energy distribution function (EEDF), challenging the conventional assumption at low partial ionisations. The effects of varying the applied voltage frequency, pulse width and rise time were also systematically examined.
- 4 March 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 35 (3)
Open AccessExperimentally informed modelling of argon dielectric barrier discharge
Low-pressure (1.3 Torr) plasma breakdown in an asymmetric argon DBD with a 10 mm gap was investigated both numerically and experimentally. A one-dimensional fluid model was validated against the experimentally obtained optical emission spectroscopy (OES) spectra, high-speed imaging and plasma current measurements. The model predicts distinct spatio-temporal oscillations in charged particle densities preceding breakdown, these are confirmed experimentally. OES analysis supports a Druyvesteyn form of the electron energy distribution function (EEDF), challenging the conventional assumption at low partial ionisations. The effects of varying the applied voltage frequency, pulse width and rise time were also systematically examined.
- Open Access
- 1 August 2025
- Published by IOP Publishing in Materials Research Express
- Vol. 12 (8) , 086401
Sputtering yield amplification of Si through the addition of Cu, Mo, or Ta
In the sputtering process, the cascade of collisions in the target surface plays a crucial role, as it determines the emission mechanics of the sputtered atoms. This phenomenon is typically described for targets composed of a single elemental type. However, introducing a second element with a different atomic mass can alter the collision cascade. In 1992, S. Berg et al introduced a method to enhance the number of sputtered atoms from doped targets, a phenomenon known as Sputtering Yield Amplification (SYA). However, there seems to be a limit to the effective concentration of dopant atoms, and the reasons why certain dopants can promote or fail to produce SYA remain unclear. In this study, we investigated the influence of gas pressure on SYA of magnetron sputtering of a silicon target doped with molybdenum, tantalum, or copper, focusing on gas-phase collisions between the sputtered dopant atoms and the working gas atoms. Film thickness and total atomic deposition on the substrate were quantified using profilometry and Rutherford Backscattering Spectrometry. Optical Emission Spectroscopy (OES) was employed to monitor the emission intensities of neutral and ionized species in the plasma. Additionally, the SIMTRA code was used to model the spatial distribution of redeposited dopant atoms on the target surface. The results demonstrate that SYA was consistently observed across all tested pressures and dopant elements, indicating a significant increase in the sputtering yield under various experimental conditions.
- 1 August 2025
- Published by IOP Publishing in Materials Research Express
- Vol. 12 (8) , 086401
Open AccessSputtering yield amplification of Si through the addition of Cu, Mo, or Ta
In the sputtering process, the cascade of collisions in the target surface plays a crucial role, as it determines the emission mechanics of the sputtered atoms. This phenomenon is typically described for targets composed of a single elemental type. However, introducing a second element with a different atomic mass can alter the collision cascade. In 1992, S. Berg et al introduced a method to enhance the number of sputtered atoms from doped targets, a phenomenon known as Sputtering Yield Amplification (SYA). However, there seems to be a limit to the effective concentration of dopant atoms, and the reasons why certain dopants can promote or fail to produce SYA remain unclear. In this study, we investigated the influence of gas pressure on SYA of magnetron sputtering of a silicon target doped with molybdenum, tantalum, or copper, focusing on gas-phase collisions between the sputtered dopant atoms and the working gas atoms. Film thickness and total atomic deposition on the substrate were quantified using profilometry and Rutherford Backscattering Spectrometry. Optical Emission Spectroscopy (OES) was employed to monitor the emission intensities of neutral and ionized species in the plasma. Additionally, the SIMTRA code was used to model the spatial distribution of redeposited dopant atoms on the target surface. The results demonstrate that SYA was consistently observed across all tested pressures and dopant elements, indicating a significant increase in the sputtering yield under various experimental conditions.
- Open Access
- 24 September 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (6)
Analysis of pulsed direct current reactive magnetron sputtering on a silicon target
Reactive sputtering is a very useful technique, particularly, for producing inhomogeneous interference filters, where the refractive index changes smoothly during deposition. In such a context, precise control of deposition parameters is crucial for replicating the desired optical properties. This study employed a pulsed DC power source to investigate the influence of a duty cycle on target poisoning, sputtering plasma characteristics, electric signals, and optical and morphological properties of synthesized films. Reactive pulsed DC magnetron sputtering was characterized by analyzing the behavior of plasma emission via optical emission spectroscopy and voltage-current signals, while modulating parameters such as the oxygen content within the vacuum chamber. A set of thin films was coated on glass substrates under different system conditions. These films underwent characterization employing spectroscopic ellipsometry to ascertain their optical constants, atomic force microscopy for surface morphology analysis, and x-ray diffraction for the determination of crystalline structures. The results indicate that longer duty cycles required higher oxygen levels to poison the target. Additionally, a detailed analysis of electrical signals revealed nonsquare waveforms, whose characteristics were influenced by both the duty cycle and the oxygen content within the sputtering chamber, resulting in higher effective voltages during the on-time of the voltage pulse. Grown films via reactive pulsed DC magnetron sputtering were also compared to films grown via conventional DC magnetron sputtering at equivalent conditions of target poisoning.
- 24 September 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (6)
Open AccessAnalysis of pulsed direct current reactive magnetron sputtering on a silicon target
Reactive sputtering is a very useful technique, particularly, for producing inhomogeneous interference filters, where the refractive index changes smoothly during deposition. In such a context, precise control of deposition parameters is crucial for replicating the desired optical properties. This study employed a pulsed DC power source to investigate the influence of a duty cycle on target poisoning, sputtering plasma characteristics, electric signals, and optical and morphological properties of synthesized films. Reactive pulsed DC magnetron sputtering was characterized by analyzing the behavior of plasma emission via optical emission spectroscopy and voltage-current signals, while modulating parameters such as the oxygen content within the vacuum chamber. A set of thin films was coated on glass substrates under different system conditions. These films underwent characterization employing spectroscopic ellipsometry to ascertain their optical constants, atomic force microscopy for surface morphology analysis, and x-ray diffraction for the determination of crystalline structures. The results indicate that longer duty cycles required higher oxygen levels to poison the target. Additionally, a detailed analysis of electrical signals revealed nonsquare waveforms, whose characteristics were influenced by both the duty cycle and the oxygen content within the sputtering chamber, resulting in higher effective voltages during the on-time of the voltage pulse. Grown films via reactive pulsed DC magnetron sputtering were also compared to films grown via conventional DC magnetron sputtering at equivalent conditions of target poisoning.
- 18 April 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 57 (28) , 285302
Plasma emission spectroscopy and optical properties of reactive-sputtered silicon oxynitride films
Silicon oxynitride (SiO x N y ) thin films were synthesized via reactive direct current magnetron sputtering under different reactive gas mass flow ratios (O2:N2) and discharge powers. The process was monitored by optical emission spectroscopy (OES), while spectroscopic ellipsometry was used to characterize the optical properties of the thin films and deposition rates. In this work, the plasma generated under different deposition parameters is analyzed by monitoring the emission lines of different species (Si I, Ar I, O2, and N2) and these results are then correlated with the corresponding target poisoning process and the optical properties of the grown thin films. According to the spectral analysis, the emission lines proved to be sensitive to the synthesis process as it was possible to differentiate deposition variations when other parameters remained unchanged. Furthermore, similar plasma conditions determined via the emission of different species were found to produce consistent thin film optical properties and vice versa. OES showed to be an effective method of monitoring and controlling the deposition of SiO x N y thin films with specific compositions.
- 18 April 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 57 (28) , 285302
Plasma emission spectroscopy and optical properties of reactive-sputtered silicon oxynitride films
Silicon oxynitride (SiO x N y ) thin films were synthesized via reactive direct current magnetron sputtering under different reactive gas mass flow ratios (O2:N2) and discharge powers. The process was monitored by optical emission spectroscopy (OES), while spectroscopic ellipsometry was used to characterize the optical properties of the thin films and deposition rates. In this work, the plasma generated under different deposition parameters is analyzed by monitoring the emission lines of different species (Si I, Ar I, O2, and N2) and these results are then correlated with the corresponding target poisoning process and the optical properties of the grown thin films. According to the spectral analysis, the emission lines proved to be sensitive to the synthesis process as it was possible to differentiate deposition variations when other parameters remained unchanged. Furthermore, similar plasma conditions determined via the emission of different species were found to produce consistent thin film optical properties and vice versa. OES showed to be an effective method of monitoring and controlling the deposition of SiO x N y thin films with specific compositions.
- 1 July 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (37) , 375201
Si sputtering yield amplification: a study of the collisions cascade and species in the sputtering plasma
The sputtering yield amplification (SYA) is a phenomenon based on doping a sputtering target with atoms of higher atomic mass. This doping changes the depth and the direction of the collision cascade in the target surface promoting a higher ejection of target atoms. In this work, we present a new way of generating the SYA phenomenon without the need of expensive and complex deposition systems. This was accomplished by increasing the working pressure and adding small pieces of W, as dopant element, on the racetrack of a Si target. The physical phenomena necessary to promote the SYA, for our experimental parameters, were analysed in two different deposition chambers and two sizes of sputtering targets. Based on the collisions in the gas phase, a calculation on the number of W atoms returning to the racetrack area was made, considering the number of atoms deposited on the thin films, to determine their effect on the cascade of collisions. In addition, calculations with the simulation of metal transport code were developed to determine the location on the racetrack zone the returning atoms were redeposited. By using reference samples placed on the racetrack of the Si target, we found that the percentage of SYA depends on the number of dopant atoms redeposited as well as the depth distribution these atoms had in the racetrack surface.
- 1 July 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (37) , 375201
Si sputtering yield amplification: a study of the collisions cascade and species in the sputtering plasma
The sputtering yield amplification (SYA) is a phenomenon based on doping a sputtering target with atoms of higher atomic mass. This doping changes the depth and the direction of the collision cascade in the target surface promoting a higher ejection of target atoms. In this work, we present a new way of generating the SYA phenomenon without the need of expensive and complex deposition systems. This was accomplished by increasing the working pressure and adding small pieces of W, as dopant element, on the racetrack of a Si target. The physical phenomena necessary to promote the SYA, for our experimental parameters, were analysed in two different deposition chambers and two sizes of sputtering targets. Based on the collisions in the gas phase, a calculation on the number of W atoms returning to the racetrack area was made, considering the number of atoms deposited on the thin films, to determine their effect on the cascade of collisions. In addition, calculations with the simulation of metal transport code were developed to determine the location on the racetrack zone the returning atoms were redeposited. By using reference samples placed on the racetrack of the Si target, we found that the percentage of SYA depends on the number of dopant atoms redeposited as well as the depth distribution these atoms had in the racetrack surface.
- 1 February 2021
- Published by Elsevier in Materials Letters
- Vol. 285
Plasma optical emission spectroscopy as a tool to monitor TiNx deposition via reactive magnetron sputtering
- 1 February 2021
- Published by Elsevier in Materials Letters
- Vol. 285
Plasma optical emission spectroscopy as a tool to monitor TiNx deposition via reactive magnetron sputtering
- 1 January 2020
- Published by Elsevier in Energy and Buildings
- Vol. 206
Novel Low-E filter for architectural glass pane
- 1 January 2020
- Published by Elsevier in Energy and Buildings
- Vol. 206
Novel Low-E filter for architectural glass pane
- 18 September 2019
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 52 (49) , 495201
Modeling the thickness distribution of silicon oxide thin films grown by reactive magnetron sputtering
Target poisoning in reactive sputtering is one of the biggest problems in the coatings industry. In this work, we use the co-sputtering simulation reactive mode software, Co-SS Rm, to present a different solution of the compound formation both on the target and on the substrate, based on the comparison of the simulations with the thickness measurements of the films deposited at different flows of reactive gas. In these simulations, the spatial distribution of the deposited thin films is determined by analysing the angular distribution of the atoms and/or compound ejected from the target, as well as its sputtering yield. Results indicate that the target surface poisoning suffers an evolution ejecting metallic atoms and silicon oxide until the whole racetrack area is covered by silicon oxide, but at the same time, there is a reduction in the racetrack area due to the growth of several monolayers of silicon oxide. Spectroscopic ellipsometry analysis showed the formation of SiO 2 in the thin films in almost all the reactive gas flows. Simulation results were validated by thickness measurements of actual thin films and plasma optical emission spectroscopy by analysing emission transitions from the target species (Si).
- 18 September 2019
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 52 (49) , 495201
Modeling the thickness distribution of silicon oxide thin films grown by reactive magnetron sputtering
Target poisoning in reactive sputtering is one of the biggest problems in the coatings industry. In this work, we use the co-sputtering simulation reactive mode software, Co-SS Rm, to present a different solution of the compound formation both on the target and on the substrate, based on the comparison of the simulations with the thickness measurements of the films deposited at different flows of reactive gas. In these simulations, the spatial distribution of the deposited thin films is determined by analysing the angular distribution of the atoms and/or compound ejected from the target, as well as its sputtering yield. Results indicate that the target surface poisoning suffers an evolution ejecting metallic atoms and silicon oxide until the whole racetrack area is covered by silicon oxide, but at the same time, there is a reduction in the racetrack area due to the growth of several monolayers of silicon oxide. Spectroscopic ellipsometry analysis showed the formation of SiO 2 in the thin films in almost all the reactive gas flows. Simulation results were validated by thickness measurements of actual thin films and plasma optical emission spectroscopy by analysing emission transitions from the target species (Si).