David G. Brandner
Research Subjects
David G. Brandner has a total of 135 co-authors. Here are the top co-authors by number of shared publications:
- Gregg T. Beckham
Renewable Resources and Enabling Sciences Center, National Laboratory of the Rockies, Golden, USA
15 shared publications - Yuriy Román-Leshkov
Department of Chemical Engineering, Massachusetts Institute of Technology, Cambridge, MA 02139, USA
10 shared publications Jacob K. Kenny
Renewable Resources and Enabling Sciences Center
4 shared publications- Jeremy R. Bussard
Renewable Resources and Enabling Sciences Center
4 shared publications - Lorenz P. Manker
National Bioenergy Center, National Renewable Energy Laboratory, Golden, USA
4 shared publications - Earl D. Christensen
National Renewable Energy Laboratory, Golden, Colorado 80401, United States
3 shared publications
Latest Publications
- Open Access
- 28 January 2026
- Published by Office of Scientific and Technical Information (OSTI)
Bio-Based Acetonitrile Production
The purpose of this CRADA is to produce at minimum 100 g of specified (99.8 wt%) acetonitrile from the nitrilation reaction using commercially available biologically derived acetic acid. This CRADA will also investigate the separation of pullulan from fermentation broth.
- 28 January 2026
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessBio-Based Acetonitrile Production
The purpose of this CRADA is to produce at minimum 100 g of specified (99.8 wt%) acetonitrile from the nitrilation reaction using commercially available biologically derived acetic acid. This CRADA will also investigate the separation of pullulan from fermentation broth.
- 27 October 2025
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 13 (44) , 19199-19209
Lignin-Derived Phenolic Compounds and Water Are Effective Cosolvents for Reductive Catalytic Fractionation
- 27 October 2025
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 13 (44) , 19199-19209
Lignin-Derived Phenolic Compounds and Water Are Effective Cosolvents for Reductive Catalytic Fractionation
- Open Access
- 1 August 2025
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 13 (31) , 12573-12582
Lignin Extraction and Condensation as a Function of Temperature, Residence Time, and Solvent System in Flow-through Reactors
Solvolytic extraction of lignin from biomass is a critical step in lignin-first biorefining, including the reductive catalytic fractionation (RCF) process. Key to optimal RCF processing is the ability to rapidly extract lignin from biomass at high delignification extents and transfer the lignin molecules to a catalyst surface in a time frame that minimizes lignin condensation reactions. Here, we use a flow-through reactor to study the effects of temperature (175–250 °C), residence time (9 to 36 min), and solvent composition (methanol and methanol–water) on lignin extraction and condensation. We evaluated three metrics at each condition: total delignification, delignification rate, and extent of condensation, the latter measured by a decrease in monomer yield for batch hydrogenolysis reactions of solvolysis liquor compared to batch RCF reactions. We observe that delignification is predominantly determined by temperature, while residence time dictates the lignin condensation extent. Moreover, the extent of both extraction and condensation increased in the methanol–water solvent system compared to that in the methanol system. Lignin extracted in methanol is stable up to 18-min residence times at or below 225 °C, while a majority of the lignin extracted in methanol–water is condensed with a 9-min residence time at 200 °C. These results can inform reactor designs and solvent selection for lignin-first biorefining processes that aim to physically separate the biomass and catalyst.
- 1 August 2025
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 13 (31) , 12573-12582
Open AccessLignin Extraction and Condensation as a Function of Temperature, Residence Time, and Solvent System in Flow-through Reactors
Solvolytic extraction of lignin from biomass is a critical step in lignin-first biorefining, including the reductive catalytic fractionation (RCF) process. Key to optimal RCF processing is the ability to rapidly extract lignin from biomass at high delignification extents and transfer the lignin molecules to a catalyst surface in a time frame that minimizes lignin condensation reactions. Here, we use a flow-through reactor to study the effects of temperature (175–250 °C), residence time (9 to 36 min), and solvent composition (methanol and methanol–water) on lignin extraction and condensation. We evaluated three metrics at each condition: total delignification, delignification rate, and extent of condensation, the latter measured by a decrease in monomer yield for batch hydrogenolysis reactions of solvolysis liquor compared to batch RCF reactions. We observe that delignification is predominantly determined by temperature, while residence time dictates the lignin condensation extent. Moreover, the extent of both extraction and condensation increased in the methanol–water solvent system compared to that in the methanol system. Lignin extracted in methanol is stable up to 18-min residence times at or below 225 °C, while a majority of the lignin extracted in methanol–water is condensed with a 9-min residence time at 200 °C. These results can inform reactor designs and solvent selection for lignin-first biorefining processes that aim to physically separate the biomass and catalyst.
- Open Access
- 5 June 2024
- Published by American Chemical Society (ACS) in JACS Au
- Vol. 4 (6) , 2173-2187
Design and Validation of a High-Throughput Reductive Catalytic Fractionation Method
Reductive catalytic fractionation (RCF) is a promising method to extract and depolymerize lignin from biomass, and bench-scale studies have enabled considerable progress in the past decade. RCF experiments are typically conducted in pressurized batch reactors with volumes ranging between 50 and 1000 mL, limiting the throughput of these experiments to one to six reactions per day for an individual researcher. Here, we report a high-throughput RCF (HTP-RCF) method in which batch RCF reactions are conducted in 1 mL wells machined directly into Hastelloy reactor plates. The plate reactors can seal high pressures produced by organic solvents by vertically stacking multiple reactor plates, leading to a compact and modular system capable of performing 240 reactions per experiment. Using this setup, we screened solvent mixtures and catalyst loadings for hydrogen-free RCF using 50 mg poplar and 0.5 mL reaction solvent. The system of 1:1 isopropanol/methanol showed optimal monomer yields and selectivity to 4-propyl substituted monomers, and validation reactions using 75 mL batch reactors produced identical monomer yields. To accommodate the low material loadings, we then developed a workup procedure for parallel filtration, washing, and drying of samples and a 1H nuclear magnetic resonance spectroscopy method to measure the RCF oil yield without performing liquid-liquid extraction. As a demonstration of this experimental pipeline, 50 unique switchgrass samples were screened in RCF reactions in the HTP-RCF system, revealing a wide range of monomer yields (21-36%), S/G ratios (0.41-0.93), and oil yields (40-75%). These results were successfully validated by repeating RCF reactions in 75 mL batch reactors for a subset of samples. We anticipate that this approach can be used to rapidly screen substrates, catalysts, and reaction conditions in high-pressure batch reactions with higher throughput than standard batch reactors.
- 5 June 2024
- Published by American Chemical Society (ACS) in JACS Au
- Vol. 4 (6) , 2173-2187
Open AccessDesign and Validation of a High-Throughput Reductive Catalytic Fractionation Method
Reductive catalytic fractionation (RCF) is a promising method to extract and depolymerize lignin from biomass, and bench-scale studies have enabled considerable progress in the past decade. RCF experiments are typically conducted in pressurized batch reactors with volumes ranging between 50 and 1000 mL, limiting the throughput of these experiments to one to six reactions per day for an individual researcher. Here, we report a high-throughput RCF (HTP-RCF) method in which batch RCF reactions are conducted in 1 mL wells machined directly into Hastelloy reactor plates. The plate reactors can seal high pressures produced by organic solvents by vertically stacking multiple reactor plates, leading to a compact and modular system capable of performing 240 reactions per experiment. Using this setup, we screened solvent mixtures and catalyst loadings for hydrogen-free RCF using 50 mg poplar and 0.5 mL reaction solvent. The system of 1:1 isopropanol/methanol showed optimal monomer yields and selectivity to 4-propyl substituted monomers, and validation reactions using 75 mL batch reactors produced identical monomer yields. To accommodate the low material loadings, we then developed a workup procedure for parallel filtration, washing, and drying of samples and a 1H nuclear magnetic resonance spectroscopy method to measure the RCF oil yield without performing liquid-liquid extraction. As a demonstration of this experimental pipeline, 50 unique switchgrass samples were screened in RCF reactions in the HTP-RCF system, revealing a wide range of monomer yields (21-36%), S/G ratios (0.41-0.93), and oil yields (40-75%). These results were successfully validated by repeating RCF reactions in 75 mL batch reactors for a subset of samples. We anticipate that this approach can be used to rapidly screen substrates, catalysts, and reaction conditions in high-pressure batch reactions with higher throughput than standard batch reactors.
- Open Access
- 12 April 2023
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 25 (9) , 3660-3670
Feedstock-agnostic reductive catalytic fractionation in alcohol and alcohol–water mixtures
This work demonstrates that reductive catalytic fractionation can be a feedstock-agnostic process on hardwoods, softwoods, agricultural residues, and grasses, especially with water-alcohol solvent mixtures.
- 12 April 2023
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 25 (9) , 3660-3670
Open AccessFeedstock-agnostic reductive catalytic fractionation in alcohol and alcohol–water mixtures
This work demonstrates that reductive catalytic fractionation can be a feedstock-agnostic process on hardwoods, softwoods, agricultural residues, and grasses, especially with water-alcohol solvent mixtures.
- Open Access
- 13 March 2023
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 11 (12) , 4517-4522
Interdependence of Solvent and Catalyst Selection on Low Pressure Hydrogen-Free Reductive Catalytic Fractionation
- 13 March 2023
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 11 (12) , 4517-4522
Open AccessInterdependence of Solvent and Catalyst Selection on Low Pressure Hydrogen-Free Reductive Catalytic Fractionation
- Open Access
- 26 October 2022
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 24 (22) , 8733-8741
Lignin alkaline oxidation using reversibly-soluble bases
When excess base is required to drive desired reactions, such as in lignin alkaline oxidation, Sr(OH)2 can offer a reversibly-soluble alternative to NaOH that allows simple recycle of the excess base with concomitant cost and environmental benefits.
- 26 October 2022
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 24 (22) , 8733-8741
Open AccessLignin alkaline oxidation using reversibly-soluble bases
When excess base is required to drive desired reactions, such as in lignin alkaline oxidation, Sr(OH)2 can offer a reversibly-soluble alternative to NaOH that allows simple recycle of the excess base with concomitant cost and environmental benefits.
- Top Cited Papers
- 14 October 2022
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 378 (6616) , 207-211
Mixed plastics waste valorization through tandem chemical oxidation and biological funneling
Mixed plastics waste represents an abundant and largely untapped feedstock for the production of valuable products. The chemical diversity and complexity of these materials, however, present major barriers to realizing this opportunity. In this work, we show that metal-catalyzed autoxidation depolymerizes comingled polymers into a mixture of oxygenated small molecules that are advantaged substrates for biological conversion. We engineer a robust soil bacterium, Pseudomonas putida , to funnel these oxygenated compounds into a single exemplary chemical product, either β-ketoadipate or polyhydroxyalkanoates. This hybrid process establishes a strategy for the selective conversion of mixed plastics waste into useful chemical products.
- 14 October 2022
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 378 (6616) , 207-211
Top Cited PapersMixed plastics waste valorization through tandem chemical oxidation and biological funneling
Mixed plastics waste represents an abundant and largely untapped feedstock for the production of valuable products. The chemical diversity and complexity of these materials, however, present major barriers to realizing this opportunity. In this work, we show that metal-catalyzed autoxidation depolymerizes comingled polymers into a mixture of oxygenated small molecules that are advantaged substrates for biological conversion. We engineer a robust soil bacterium, Pseudomonas putida , to funnel these oxygenated compounds into a single exemplary chemical product, either β-ketoadipate or polyhydroxyalkanoates. This hybrid process establishes a strategy for the selective conversion of mixed plastics waste into useful chemical products.
- Open Access
- 16 August 2022
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 7 (12) , 2527-2533
Catalyst choice impacts aromatic monomer yields and selectivity in hydrogen-free reductive catalytic fractionation
Hydrogen-free reductive catalytic fractionation (RCF) is a promising method to extract and depolymerize lignin from native biomass without the use of external hydrogen gas. Here, we show that Pt/C and Pd/C achieve comparable monomer yields regardless of hydrogen pressure, whereas Ru/C and Ni/C show lower yields under H2-free conditions. Ru/C and Ni/C primarily perform hydrodeoxygenation regardless of the hydrogen pressure, but Pt/C and Pd/C demonstrated the ability to form both ethyl products from dehydrogenation and propanol products through hydrogenation depending on the presence of external H2. Adding water to the solvent increased HDO selectivity to propyl products for both Pt/C and Pd/C. Monomer yields from poplar RCF showed similar trends in yield and selectivity to reactions with the model compound coniferyl alcohol, suggesting that H2-free RCF performance is dictated by the stabilization rate of reactive monomer intermediates.
- 16 August 2022
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 7 (12) , 2527-2533
Open AccessCatalyst choice impacts aromatic monomer yields and selectivity in hydrogen-free reductive catalytic fractionation
Hydrogen-free reductive catalytic fractionation (RCF) is a promising method to extract and depolymerize lignin from native biomass without the use of external hydrogen gas. Here, we show that Pt/C and Pd/C achieve comparable monomer yields regardless of hydrogen pressure, whereas Ru/C and Ni/C show lower yields under H2-free conditions. Ru/C and Ni/C primarily perform hydrodeoxygenation regardless of the hydrogen pressure, but Pt/C and Pd/C demonstrated the ability to form both ethyl products from dehydrogenation and propanol products through hydrogenation depending on the presence of external H2. Adding water to the solvent increased HDO selectivity to propyl products for both Pt/C and Pd/C. Monomer yields from poplar RCF showed similar trends in yield and selectivity to reactions with the model compound coniferyl alcohol, suggesting that H2-free RCF performance is dictated by the stabilization rate of reactive monomer intermediates.
- 21 June 2021
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 23 (15) , 5437-5441
Flow-through solvolysis enables production of native-like lignin from biomass
Flow-through solvolysis offers an opportunity to limit lignin condensation reactions that prevent isolation of native lignin in biomass processing, thus allowing for the study of intrinsic lignin properties and steady-state lignin depolymerization.
- 21 June 2021
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 23 (15) , 5437-5441
Flow-through solvolysis enables production of native-like lignin from biomass
Flow-through solvolysis offers an opportunity to limit lignin condensation reactions that prevent isolation of native lignin in biomass processing, thus allowing for the study of intrinsic lignin properties and steady-state lignin depolymerization.