Ronghui Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ronghui Lin has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Xiaohang Li
Advanced Semiconductor Laboratory, Electrical and Computer Engineering Program, CEMSE Division, King Abdullah University of Science and Technology (KAUST) 1 , Thuwal 23955-6900
14 shared publications - Kuang-Hui Li
Photonics Laboratory, Computer, Electrical and Mathematical Sciences and Engineering Division (CEMSE), King Abdullah University of Science and Technology (KAUST) 1 , Thuwal 23955-6900, Saudi Arabia
6 shared publications - Haiding Sun
University of Science and Technology of China
4 shared publications Haiding Sun
Advanced Semiconductor Laboratory King Abdullah University of Science and Technology (KAUST) Thuwal 23955‐6900 Saudi Arabia
3 shared publications- Tien Khee Ng
King Abdullah University of Science and Technology (KAUST)
3 shared publications - Bilal Janjua
King Abdullah Univ. of Science and Technology (Saudi Arabia)
2 shared publications
Latest Publications
- Open Access
Bipolar photovoltaic effect in InSe / MoO 3 van der Waals heterostructure for spontaneous light polarization detection
Polarization is one of the most fundamental properties of light. Traditional polarization‐sensitive photodetectors, however, are limited in their ability to fully extract this information, as they translate the two orthogonal polarization states into currents of the same polarity. In this work, we unveil a new mechanism that could switch the photocurrent direction based on the polarization of the incident light. By leveraging the fact that shift current is not constrained by the built‐in electric field of the heterojunction, we engineer the dynamic cancellation between shift and drift currents under specific photon energy and polarization conditions, leading to a reversible switch in photocurrent polarity. This approach leads to a reversible change in photocurrent polarity, allowing the anisotropic ratio of the detector to exceed the conventional limit. Additionally, the detector can automatically assign opposite currents to orthogonal linear polarization states, effectively mapping polarization into a ternary state. This enhancement significantly increases the information density, making it particularly advantageous for applications such as optical computing and optical communications. image
Open AccessBipolar photovoltaic effect in InSe / MoO 3 van der Waals heterostructure for spontaneous light polarization detection
Polarization is one of the most fundamental properties of light. Traditional polarization‐sensitive photodetectors, however, are limited in their ability to fully extract this information, as they translate the two orthogonal polarization states into currents of the same polarity. In this work, we unveil a new mechanism that could switch the photocurrent direction based on the polarization of the incident light. By leveraging the fact that shift current is not constrained by the built‐in electric field of the heterojunction, we engineer the dynamic cancellation between shift and drift currents under specific photon energy and polarization conditions, leading to a reversible switch in photocurrent polarity. This approach leads to a reversible change in photocurrent polarity, allowing the anisotropic ratio of the detector to exceed the conventional limit. Additionally, the detector can automatically assign opposite currents to orthogonal linear polarization states, effectively mapping polarization into a ternary state. This enhancement significantly increases the information density, making it particularly advantageous for applications such as optical computing and optical communications. image
- Open Access
- 1 March 2026
- Published by AIP Publishing in APL Engineering Physics
- Vol. 1 (1)
Spectrally tunable singular phase at normal incidence in nanophotonic cavities
The concept of singular phases at the point of darkness has been extensively studied using various optical systems, such as metamaterials and thin-film cavities, mainly for refractive index sensing. However, these systems typically work at an oblique angle of incidence. Achieving a singular phase at normal incidence is vital for practical sensing and flat-optics applications, but it remains challenging. Here, we demonstrate the singular phase at normal incidence using a grating-coupled thin-film cavity that functions at optical wavelengths. By optimizing the structural parameters of the grating and thin-film cavity, we achieve zero reflection with an abrupt phase shift at the polarization-dependent resonance of the grating. In addition, we introduce a spectrally tunable singular phase at normal incidence by integrating a phase change material (PCM) into the cavity. Using a lossless PCM, such as Sb2S3, we achieve a phase singularity with continuous spectral tunability up to 203 nm by altering its phase from amorphous to crystalline, a key feature for phase engineering in flat optics.
- 1 March 2026
- Published by AIP Publishing in APL Engineering Physics
- Vol. 1 (1)
Open AccessSpectrally tunable singular phase at normal incidence in nanophotonic cavities
The concept of singular phases at the point of darkness has been extensively studied using various optical systems, such as metamaterials and thin-film cavities, mainly for refractive index sensing. However, these systems typically work at an oblique angle of incidence. Achieving a singular phase at normal incidence is vital for practical sensing and flat-optics applications, but it remains challenging. Here, we demonstrate the singular phase at normal incidence using a grating-coupled thin-film cavity that functions at optical wavelengths. By optimizing the structural parameters of the grating and thin-film cavity, we achieve zero reflection with an abrupt phase shift at the polarization-dependent resonance of the grating. In addition, we introduce a spectrally tunable singular phase at normal incidence by integrating a phase change material (PCM) into the cavity. Using a lossless PCM, such as Sb2S3, we achieve a phase singularity with continuous spectral tunability up to 203 nm by altering its phase from amorphous to crystalline, a key feature for phase engineering in flat optics.
- 2 September 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (19) , 34117-34128
Reflective metalens with an enhanced off-axis focusing performance
Metalenses are one of the most promising metasurface applications. However, all-dielectric reflective metalenses are rarely studied, especially regarding their off-axis focusing performance. After experimentally studying the material optical properties in this work, we propose reflective metalens based on titanium dioxide (TiO2) and silicon dioxide (SiO2), which operate at a visible wavelength of 0.633 µm. Unlike conventional reflective metalenses based on metallic mirrors, the proposed device was designed based on a modified parabolic phase profile and was integrated onto a dielectric distributed Bragg reflector periodic structure to achieve high reflectivity with five dielectric pairs. The focusing efficiency characteristics of the metalens were experimentally studied for beam angles of incidence between 0 ∘ and 30 ∘ . The results reveal that the focusing efficiency for the modified metalens design remains higher than 54%, which is higher than 50%, making it promising for photonic miniaturization and integration.
- 2 September 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (19) , 34117-34128
Reflective metalens with an enhanced off-axis focusing performance
Metalenses are one of the most promising metasurface applications. However, all-dielectric reflective metalenses are rarely studied, especially regarding their off-axis focusing performance. After experimentally studying the material optical properties in this work, we propose reflective metalens based on titanium dioxide (TiO2) and silicon dioxide (SiO2), which operate at a visible wavelength of 0.633 µm. Unlike conventional reflective metalenses based on metallic mirrors, the proposed device was designed based on a modified parabolic phase profile and was integrated onto a dielectric distributed Bragg reflector periodic structure to achieve high reflectivity with five dielectric pairs. The focusing efficiency characteristics of the metalens were experimentally studied for beam angles of incidence between 0 ∘ and 30 ∘ . The results reveal that the focusing efficiency for the modified metalens design remains higher than 54%, which is higher than 50%, making it promising for photonic miniaturization and integration.
- Open Access
- 22 September 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (10) , 2466
Low Resistance Asymmetric III-Nitride Tunnel Junctions Designed by Machine Learning
The tunnel junction (TJ) is a crucial structure for numerous III-nitride devices. A fundamental challenge for TJ design is to minimize the TJ resistance at high current densities. In this work, we propose the asymmetric p-AlGaN/i-InGaN/n-AlGaN TJ structure for the first time. P-AlGaN/i-InGaN/n-AlGaN TJs were simulated with different Al or In compositions and different InGaN layer thicknesses using TCAD (Technology Computer-Aided Design) software. Trained by these data, we constructed a highly efficient model for TJ resistance prediction using machine learning. The model constructs a tool for real-time prediction of the TJ resistance, and the resistances for 22,254 different TJ structures were predicted. Based on our TJ predictions, the asymmetric TJ structure (p-Al0.7Ga0.3N/i-In0.2Ga0.8N/n-Al0.3Ga0.7N) with higher Al composition in p-layer has seven times lower TJ resistance compared to the prevailing symmetric p-Al0.3Ga0.7N/i-In0.2Ga0.8N/n-Al0.3Ga0.7N TJ. This study paves a new way in III-nitride TJ design for optical and electronic devices.
- 22 September 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (10) , 2466
Open AccessLow Resistance Asymmetric III-Nitride Tunnel Junctions Designed by Machine Learning
The tunnel junction (TJ) is a crucial structure for numerous III-nitride devices. A fundamental challenge for TJ design is to minimize the TJ resistance at high current densities. In this work, we propose the asymmetric p-AlGaN/i-InGaN/n-AlGaN TJ structure for the first time. P-AlGaN/i-InGaN/n-AlGaN TJs were simulated with different Al or In compositions and different InGaN layer thicknesses using TCAD (Technology Computer-Aided Design) software. Trained by these data, we constructed a highly efficient model for TJ resistance prediction using machine learning. The model constructs a tool for real-time prediction of the TJ resistance, and the resistances for 22,254 different TJ structures were predicted. Based on our TJ predictions, the asymmetric TJ structure (p-Al0.7Ga0.3N/i-In0.2Ga0.8N/n-Al0.3Ga0.7N) with higher Al composition in p-layer has seven times lower TJ resistance compared to the prevailing symmetric p-Al0.3Ga0.7N/i-In0.2Ga0.8N/n-Al0.3Ga0.7N TJ. This study paves a new way in III-nitride TJ design for optical and electronic devices.
- 22 March 2021
- Published by Optica Publishing Group in Photonics Research
- Vol. 9 (4) , B96-B103
Engineering of multiple bound states in the continuum by latent representation of freeform structures
We demonstrate a neural network capable of designing on-demand multiple symmetry-protected bound states in the continuum (BICs) in freeform structures with predefined symmetry. The latent representation of the freeform structures allows the tuning of the geometry in a differentiable, continuous way. We show the rich band inversion and accidental degeneracy in these freeform structures by interacting with the latent representation directly. Moreover, a high design accuracy is demonstrated for arbitrary control of multiple BIC frequencies by using a photonic property readout network to interpret the latent representation.
- 22 March 2021
- Published by Optica Publishing Group in Photonics Research
- Vol. 9 (4) , B96-B103
Engineering of multiple bound states in the continuum by latent representation of freeform structures
We demonstrate a neural network capable of designing on-demand multiple symmetry-protected bound states in the continuum (BICs) in freeform structures with predefined symmetry. The latent representation of the freeform structures allows the tuning of the geometry in a differentiable, continuous way. We show the rich band inversion and accidental degeneracy in these freeform structures by interacting with the latent representation directly. Moreover, a high design accuracy is demonstrated for arbitrary control of multiple BIC frequencies by using a photonic property readout network to interpret the latent representation.
- Open Access
- 7 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 12 (4) , 1-7
Analysis of Tapered Nanopillars for Reflective Metalens: The Role of Higher-Order Modes
Despite the widespread interest in the metalens technology, few works show the errors during fabrication and analyze how they influence the focusing performance. In this work, we proposed a reflective metalens design and carry out a fundamental study on how a mild tapering angle (<6) of the nanopillars would influence the performance of a reflective metalens. By analyzing the interaction of Mie resonance in the lateral direction and Fabry-Prot resonance in the longitudinal direction using numerical simulations, we reveal the detrimental role the tapering angle plays due to the low transmission near the resonance. We observe the weakening of the electric quadrupole and magnetic dipole response, and the increase of the electric dipole response for tapered nanopillars. Moreover, the Fabry-Prot resonance is disturbed due to the broken symmetry. These factors contribute to lower Q factor resonance and hence the low transmission. The results presented in this work can guide the analysis of fabrication errors and provide insights on how to compensate them.
- 7 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 12 (4) , 1-7
Open AccessAnalysis of Tapered Nanopillars for Reflective Metalens: The Role of Higher-Order Modes
Despite the widespread interest in the metalens technology, few works show the errors during fabrication and analyze how they influence the focusing performance. In this work, we proposed a reflective metalens design and carry out a fundamental study on how a mild tapering angle (<6) of the nanopillars would influence the performance of a reflective metalens. By analyzing the interaction of Mie resonance in the lateral direction and Fabry-Prot resonance in the longitudinal direction using numerical simulations, we reveal the detrimental role the tapering angle plays due to the low transmission near the resonance. We observe the weakening of the electric quadrupole and magnetic dipole response, and the increase of the electric dipole response for tapered nanopillars. Moreover, the Fabry-Prot resonance is disturbed due to the broken symmetry. These factors contribute to lower Q factor resonance and hence the low transmission. The results presented in this work can guide the analysis of fabrication errors and provide insights on how to compensate them.
- 4 March 2020
- Published by Optica Publishing Group in Optics Letters
- Vol. 45 (6) , 1362-1365
Inverse design of plasmonic metasurfaces by convolutional neural network
Artificial neural networks have shown effectiveness in the inverse design of nanophotonic structures; however, the numerical accuracy and algorithm efficiency are not analyzed adequately in previous reports. In this Letter, we demonstrate the convolutional neural network as an inverse design tool to achieve high numerical accuracy in plasmonic metasurfaces. A comparison of the convolutional neural networks and the fully connected neural networks show that convolutional neural networks have higher generalization capabilities. We share practical guidelines for optimizing the neural network and analyzed the hierarchy of accuracy in the multi-parameter inverse design of plasmonic metasurfaces. A high inverse design accuracy of ± 8 n m for the critical geometrical parameters is demonstrated.
- 4 March 2020
- Published by Optica Publishing Group in Optics Letters
- Vol. 45 (6) , 1362-1365
Inverse design of plasmonic metasurfaces by convolutional neural network
Artificial neural networks have shown effectiveness in the inverse design of nanophotonic structures; however, the numerical accuracy and algorithm efficiency are not analyzed adequately in previous reports. In this Letter, we demonstrate the convolutional neural network as an inverse design tool to achieve high numerical accuracy in plasmonic metasurfaces. A comparison of the convolutional neural networks and the fully connected neural networks show that convolutional neural networks have higher generalization capabilities. We share practical guidelines for optimizing the neural network and analyzed the hierarchy of accuracy in the multi-parameter inverse design of plasmonic metasurfaces. A high inverse design accuracy of ± 8 n m for the critical geometrical parameters is demonstrated.
- 15 January 2020
- Published by Wiley in Laser & Photonics Reviews
- Vol. 14 (2)
On‐Chip Hyperuniform Lasers for Controllable Transitions in Disordered Systems
Designing light sources with controllable properties at the nanoscale is a main goal in research in photonics. Harnessing disorder opens many opportunities for reducing the footprints of laser devices, enabling physical phenomena and functionalities that are not observed in traditional structures. Controlling coherent light–matter interactions in systems based on randomness, however, is challenging especially if compared to traditional lasers. Here, how to overcome these issues by using semiconductor lasers created from stealthy hyperuniform structures is shown. An on‐chip InGaN hyperuniform laser is designed and experimentally demonstrated, a new type of disordered laser with controllable transitions—ranging from lasing curve slopes, thresholds, and linewidths— from the nonlinear interplay between randomness and hidden order created via hyperuniformity. Theory and experiments show that the addition of degrees of order stabilizes the lasing dynamics via mode competition effects, arising between weak light localizations of the hyperuniform structure. The properties of the laser are independent from the cavity size or the gain material, and show very little statistical fluctuations between different random samples possessing the same randomness. These results open to on‐chip lasers that combine the advantages of classical and random lasers into a single platform.
- 15 January 2020
- Published by Wiley in Laser & Photonics Reviews
- Vol. 14 (2)
On‐Chip Hyperuniform Lasers for Controllable Transitions in Disordered Systems
Designing light sources with controllable properties at the nanoscale is a main goal in research in photonics. Harnessing disorder opens many opportunities for reducing the footprints of laser devices, enabling physical phenomena and functionalities that are not observed in traditional structures. Controlling coherent light–matter interactions in systems based on randomness, however, is challenging especially if compared to traditional lasers. Here, how to overcome these issues by using semiconductor lasers created from stealthy hyperuniform structures is shown. An on‐chip InGaN hyperuniform laser is designed and experimentally demonstrated, a new type of disordered laser with controllable transitions—ranging from lasing curve slopes, thresholds, and linewidths— from the nonlinear interplay between randomness and hidden order created via hyperuniformity. Theory and experiments show that the addition of degrees of order stabilizes the lasing dynamics via mode competition effects, arising between weak light localizations of the hyperuniform structure. The properties of the laser are independent from the cavity size or the gain material, and show very little statistical fluctuations between different random samples possessing the same randomness. These results open to on‐chip lasers that combine the advantages of classical and random lasers into a single platform.
- 28 May 2019
- Published by Optica Publishing Group in Optics Letters
- Vol. 44 (11) , 2819-2822
Multifocal metalens based on multilayer Pancharatnam–Berry phase elements architecture
In this Letter, we aim to answer the fundamental question of what will happen when two layers of Pancharatnam–Berry phase elements are superimposed on each other. The different diffraction orders and their respective phase changes of this structure are investigated by Jones matrix calculations. Based on the results, we propose and demonstrate metalenses numerically that can split an incident circularly polarized beam into different helicities and focus them at different foci with controlled intensity and focal length. The decoupling of the focusing length and the relative intensity give us control to achieve an arbitrary combination of focal spot location and relative intensity. To the best of our knowledge, this is the first proposal and theoretical demonstration of bilayer Pancharatnam–Berry phase elements for metalens applications. Such a platform can be expanded to multilayers and applied to other complex functionalities such as achromatic lenses.
- 28 May 2019
- Published by Optica Publishing Group in Optics Letters
- Vol. 44 (11) , 2819-2822
Multifocal metalens based on multilayer Pancharatnam–Berry phase elements architecture
In this Letter, we aim to answer the fundamental question of what will happen when two layers of Pancharatnam–Berry phase elements are superimposed on each other. The different diffraction orders and their respective phase changes of this structure are investigated by Jones matrix calculations. Based on the results, we propose and demonstrate metalenses numerically that can split an incident circularly polarized beam into different helicities and focus them at different foci with controlled intensity and focal length. The decoupling of the focusing length and the relative intensity give us control to achieve an arbitrary combination of focal spot location and relative intensity. To the best of our knowledge, this is the first proposal and theoretical demonstration of bilayer Pancharatnam–Berry phase elements for metalens applications. Such a platform can be expanded to multilayers and applied to other complex functionalities such as achromatic lenses.
- 19 June 2018
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 5 (8) , 3305-3314
Graded-Index Separate Confinement Heterostructure AlGaN Nanowires: Toward Ultraviolet Laser Diodes Implementation
High-density dislocations in materials and poor electrical conductivity of p-type AlGaN layers constrain the performance of ultraviolet light emitting diodes and lasers at shorter wavelengths. To address those technical challenges, we design, grow, and fabricate a novel nanowire structure adopting a graded-index separate confinement heterostructure (GRINSCH) in which the active region is sandwiched between two compositionally graded AlGaN layers, namely a GRINSCH diode. Calculated electronic band diagram and carrier concentrations show an automatic formation of a p-n junction with electron and hole concentrations of ~1018 /cm3 in the graded AlGaN layers without intentional doping. The transmission electron microscopy experiment confirms the composition variation in axial direction of the graded AlGaN nanowires. Significantly lower turn-on voltage of 6.5 V (reduced by 2.5 V) and smaller series resistance of 16.7 Ω (reduced by nearly four times) are achieved in the GRINSCH diode, compared with the conventional p-i-n diode. Such an improvement in the electrical performance is mainly attributed to the effectiveness of polarization-induced n- and p-doping in the compositionally graded AlGaN layers. In consequence, the carrier transport and injection efficiency of the GRINSCH diode are greatly enhanced, which leads to a lower turn-on voltage, smaller series resistance, higher output power, and enhanced device efficiency. The calculated carrier distributions (both electrons and holes) across the active region show a better carrier confinement in the GRINSCH diode. Thus, together with the large optical confinement, the GRINSCH diode could offer an unconventional path for the development of solid-state ultraviolet optoelectronic devices, mainly laser diodes of the future.
- 19 June 2018
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 5 (8) , 3305-3314
Graded-Index Separate Confinement Heterostructure AlGaN Nanowires: Toward Ultraviolet Laser Diodes Implementation
High-density dislocations in materials and poor electrical conductivity of p-type AlGaN layers constrain the performance of ultraviolet light emitting diodes and lasers at shorter wavelengths. To address those technical challenges, we design, grow, and fabricate a novel nanowire structure adopting a graded-index separate confinement heterostructure (GRINSCH) in which the active region is sandwiched between two compositionally graded AlGaN layers, namely a GRINSCH diode. Calculated electronic band diagram and carrier concentrations show an automatic formation of a p-n junction with electron and hole concentrations of ~1018 /cm3 in the graded AlGaN layers without intentional doping. The transmission electron microscopy experiment confirms the composition variation in axial direction of the graded AlGaN nanowires. Significantly lower turn-on voltage of 6.5 V (reduced by 2.5 V) and smaller series resistance of 16.7 Ω (reduced by nearly four times) are achieved in the GRINSCH diode, compared with the conventional p-i-n diode. Such an improvement in the electrical performance is mainly attributed to the effectiveness of polarization-induced n- and p-doping in the compositionally graded AlGaN layers. In consequence, the carrier transport and injection efficiency of the GRINSCH diode are greatly enhanced, which leads to a lower turn-on voltage, smaller series resistance, higher output power, and enhanced device efficiency. The calculated carrier distributions (both electrons and holes) across the active region show a better carrier confinement in the GRINSCH diode. Thus, together with the large optical confinement, the GRINSCH diode could offer an unconventional path for the development of solid-state ultraviolet optoelectronic devices, mainly laser diodes of the future.