SLShibin Li

Shibin Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Shibin Li has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Phase-change transpiration cooling on high-speed vehicle leading edges: A pressure-adaptive LTNE-TPMM approach

    by Yunan Wang, Lin Wang, Zhenbing Luo, Zhihong Chen, Yan Zhou, Shibin Li, Xiong Deng, Wenqiang Peng

  • Numerical investigation of mass-flow-rate-based parameter compensation in multi-orifice opposing jets on a variable-bluntness leading edge

    by Qing-Yang Guo, Ming-Bo Sun, Jun-Heng Luo, Rui Ma, Shi-Bin Li

    To mitigate severe aerodynamic heating at the rudder/wing leading edges of high-speed vehicles, opposing-jet active thermal protection is investigated. Three-dimensional Reynolds-averaged Navier–Stokes simulations at Mach 8 and 30 km altitude examine single-orifice, dual-orifice, and spanwise multi-orifice jets over variable-bluntness leading edges under a constant mass flow rate constraint. The results show that the restriction on radial jet expansion caused by a reduced orifice diameter can be compensated by the enhanced expansion associated with an increased jet total pressure ratio (PR). Consequently, macroscopic shock structures and wall thermal loads remain highly consistent for different combinations of orifice diameter and PR. This compensation behavior is maintained under both strong and weak dual-orifice interference. For spanwise multi-orifice arrays, the constant mass flow rate per orifice strategy provides more uniform thermal protection than the constant PR strategy and gradually establishes a downstream dynamic equilibrium region with stable flow structures. Under constant PR, the mass flow rate and jet strength decrease with orifice size, causing pronounced increases in downstream local pressure and heat flux peaks. The present study verifies the applicability of mass-flow rate-based parameter compensation predicted by classical jet scaling relations to complex flows involving three-dimensional sweep, multi-orifice interactions, and variable-bluntness leading edges, and provides a design basis for orifice parameter matching and mass flow distribution in multi-orifice opposing-jet thermal protection systems.

  • Numerical investigation on the early-stage high-speed water entry of trans-media vehicle with spike

    by Shaliang Li, Zhexing Hou, Wei Huang, Shibin Li

    Compared with low-speed water entry, high-speed water entry involves stronger impact loads and more complex multiphase flow phenomena. Accurate prediction of flowfield evolution and impact load is therefore essential for the development of trans-media vehicles. In this study, a solver enhancement based on overInterPhaseChangeDyMFoam is proposed by combining the volume of fluid method with the Schnerr–Sauer cavitation model and incorporating air effects into a two-phase cavitation framework. This solver enables simulations of cavitation during high-speed water entry and is validated against published experimental and theoretical results. The validated solver is then used to investigate the early-stage water-entry process of a spiked trans-media vehicle, with emphasis on flowfield development and hydrodynamic response. These results show that the spike effectively induces flow separation and establishes a stable low-pressure region near the vehicle nose, thereby promoting rapid supercavity formation. The cavity maintains a slender geometry and exhibits quasi-self-similar evolution, whereas radial expansion follows a nonlinear growth trend. As the cavity gradually envelops the vehicle body, the wetted area decreases markedly. Consequently, the drag coefficient rapidly approaches a low quasi-steady level, vehicle deceleration is suppressed, and penetration depth increases approximately linearly with time.

  • Mechanisms of spike-induced cavity dynamics and drag reduction in submerged high-speed flows

    by Shaliang Li, Wei Huang, Shibin Li

    High-speed underwater vehicles experience significant hydrodynamic drag, which limits their performance and operational efficiency. Spike devices have been proposed as an effective drag-reduction technique by inducing cavity formation in front of the vehicle. This present study focuses on the drag reduction mechanism induced by a spike under fully submerged high-speed conditions. Using the three-dimensional Reynolds-averaged Navier–Stokes approach based on the interPhaseChangeFoam solver in OpenFOAM®, high-speed underwater numerical simulations are conducted to systematically investigate the effects of flow parameters and structural parameters on the flowfield characteristics and force acting on the vehicle. The results reveal that the vehicle's drag is strongly dependent on the aerodisk diameter (d), inflow velocity (v), and angle of attack (α), whereas the length-to-diameter ratio (L/D) has a comparatively minor effect. An optimal d exists, namely an excessively small d fails to achieve a stable cavity, while an excessively large d causes the drag force on the spike to increase sharply. For the hemispherical aerodisk, critical values of d and L/D exist for the occurrence of cavitation instability. In contrast, the flat-faced aerodisk can generate a stable cavity at a smaller d and exhibit weak sensitivity to L/D. Higher v promote the cavity to fully wrap the vehicle. Increasing the α disrupts flowfield symmetry, leading to a rapid drag increase beyond 6°. Selecting an appropriate d, controlling the α, and optimizing L/D are therefore key strategies to enhance drag-reduction performance of trans-media vehicles.

  • Influence of transverse jet on shock wave/boundary layer interaction and flow field of air rudder

    by Junheng Luo, Qingyang Guo, Bing Liu, Lin Wang, Shibin Li, Rui Ma

    The multi-scale flow coupling effects induced by shock wave/boundary layer interaction (SWBLI) exacerbate thermal management challenges in hypersonic aircraft. This study focuses on the air rudder to investigate the influence mechanisms of the transverse jet on SWBLI and aerothermodynamic characteristics within the rudder gap region. The numerical method has been verified with the experimental data in public literature, and a grid independence analysis has been carried out. Research results indicate that as the total pressure ratio between the jet and the freestream increases, the coverage area of thermal protection on the rudder leading edge gradually improves. However, the interaction between the jet separation shock and the rudder leading-edge shock results in a sharp rise in the peak heat flux. For a jet Mach number of 1 and a specific heat ratio of 1.4, the jet flow field characteristics remain consistent at identical mass flow rates with fixed freestream conditions and constant total jet temperature. A reduction in orifice radius balances an increase in jet pressure ratio, governing the radial expansion scale of the jet. With rudder deflection, the transverse jet effectively mitigates SWBLI by attenuating windward-side downwash effects. At 15° deflection, the jet reduces peak heat flux at the rudder shaft by 73.1% and decreases the gap region peak by 1200 kW/m2. Subsequent research should focus on the collaborative optimization of jet parameters and rudder geometry to avoid shock interference.


  • Pore-scale flow mechanisms in three-dimensional heterogeneous porous channels: Topology optimization and critical pore diameter effects

    by Rui Ma, Shibin Li, Zhongwei Wang, Lin Wang

    This paper presents a method for modeling three-dimensional heterogeneous porous channels using the variable density topology optimization technique. This approach allows for parametric control over porosity and pore throat dimensions, enabling the creation of a highly accurate geometric model. Additionally, the Navier–Stokes equations are employed to examine the pore-scale flow behavior, revealing the microscopic mechanisms through which pore structure parameters affect flow velocity, pressure drop, and nonlinear flow transition characteristics. Ultimately, a revised model for effective permeability (Keff) is introduced, enhancing the precision of macroscopic models in the cross-scale analysis of flow in porous media. The results indicate that the method of generating porous flow channels through topology optimization demonstrates high accuracy. The design error decreases as the porosity increases, reaching a minimum of 0.2% at a porosity of 0.5. It has been found that a critical pore diameter of 150 μm maximizes fluid flow velocity and minimizes critical mass flux. The effect of pore diameter on fluid velocity and vortex strength is significant, while the influence of porosity becomes apparent only at the critical pore diameter. As mass flux increases, effective permeability continuously decreases, whereas the number of vortex structures initially increases before stabilizing. The modified Keff model links pore-scale structure with macroscopic predictions, reducing the prediction error of the pressure gradient to 0.04% in cross-scale simulations. These findings provide new insights for optimizing porous media in microfluidic and energy applications.