Jose Polo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jose Polo has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Jorge Higuera
Lighting group, Catalonia Institute for Energy Research, IREC, Barcelona, Spain
6 shared publications Oscar Casas
Universitat Politecnica de Catalunya, Barcelona, Spain
2 shared publications- Oscar Lopez
Aragn Institute of Engineering Research, University of Zaragoza, Zaragoza, Spain
2 shared publications R. Pallas-Areny
2 shared publicationsA. Martinez de Olcoz
National Institute for Aerospace Technology (INTA) - SPASOLAB. Carretera de Ajalvir, km.4, 28850 Torrejón de Ardoz, Madrid, Spain
1 shared publicationAlberto García
1 shared publication
Latest Publications
- 21 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 9 (18) , 17785-17792
Time-Division Multiplexing for Power and Data Transmission on Optical Fibers
Internet of Things (IoT) raises the interconnection of low-cost sensor nodes networks everywhere even in harsh environments where conventional power supply systems and communication channels are not feasible. Power over Fiber is an alternative solution but its implementation costs are sometimes too high because of the optical devices involved. This article proposes a time-division multiplexing control algorithm and a circuit design to share the same laser diode and photodiode for power and downstream data transmission. This is a feasible solution to reduce implementation costs when sensor nodes require downstream data rates much lower than the capacity of the link.
- 21 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 9 (18) , 17785-17792
Time-Division Multiplexing for Power and Data Transmission on Optical Fibers
Internet of Things (IoT) raises the interconnection of low-cost sensor nodes networks everywhere even in harsh environments where conventional power supply systems and communication channels are not feasible. Power over Fiber is an alternative solution but its implementation costs are sometimes too high because of the optical devices involved. This article proposes a time-division multiplexing control algorithm and a circuit design to share the same laser diode and photodiode for power and downstream data transmission. This is a feasible solution to reduce implementation costs when sensor nodes require downstream data rates much lower than the capacity of the link.
- Open Access
- 1 January 2019
- Published by SAGE Publications in International Journal of Micro Air Vehicles
- Vol. 11
Micro air vehicles energy transportation for a wireless power transfer system
The aim of this work is to demonstrate the feasibility use of an Micro air vehicles (MAV) in order to power wirelessly an electric system, for example, a sensor network, using low-cost and open-source elements. To achieve this objective, an inductive system has been modelled and validated to power wirelessly a sensor node using a Crazyflie 2.0 as MAV. The design of the inductive system must be small and light enough to fulfil the requirements of the Crazyflie. An inductive model based on two resonant coils is presented. Several coils are defined to be tested using the most suitable resonant configuration. Measurements are performed to validate the model and to select the most suitable coil. While attempting to minimize the weight at transmitter’s side, on the receiver side it is intended to efficiently acquire and manage the power obtained from the transmitter. In order to prove its feasibility, a temperature sensor node is used as demonstrator. The experiment results show successfully energy transportation by MAV, and wireless power transfer for the resonant configuration, being able to completely charge the node battery and to power the temperature sensor.
- 1 January 2019
- Published by SAGE Publications in International Journal of Micro Air Vehicles
- Vol. 11
Open AccessMicro air vehicles energy transportation for a wireless power transfer system
The aim of this work is to demonstrate the feasibility use of an Micro air vehicles (MAV) in order to power wirelessly an electric system, for example, a sensor network, using low-cost and open-source elements. To achieve this objective, an inductive system has been modelled and validated to power wirelessly a sensor node using a Crazyflie 2.0 as MAV. The design of the inductive system must be small and light enough to fulfil the requirements of the Crazyflie. An inductive model based on two resonant coils is presented. Several coils are defined to be tested using the most suitable resonant configuration. Measurements are performed to validate the model and to select the most suitable coil. While attempting to minimize the weight at transmitter’s side, on the receiver side it is intended to efficiently acquire and manage the power obtained from the transmitter. In order to prove its feasibility, a temperature sensor node is used as demonstrator. The experiment results show successfully energy transportation by MAV, and wireless power transfer for the resonant configuration, being able to completely charge the node battery and to power the temperature sensor.
- 1 November 2015
- Published by Elsevier in Computers and Electronics in Agriculture
- Vol. 119, 19-32
Design of a low-cost Wireless Sensor Network with UAV mobile node for agricultural applications
- 1 November 2015
- Published by Elsevier in Computers and Electronics in Agriculture
- Vol. 119, 19-32
Design of a low-cost Wireless Sensor Network with UAV mobile node for agricultural applications
- 1 April 2014
- Published by Elsevier in Waste Management
- Vol. 34 (4) , 738-746
Intelligent composting assisted by a wireless sensing network
- 1 April 2014
- Published by Elsevier in Waste Management
- Vol. 34 (4) , 738-746
Intelligent composting assisted by a wireless sensing network
- 1 January 2012
- Published by Springer Nature
- p. 323-359
Autonomous and Interoperable Smart Sensors for Environmental Monitoring Applications
- 1 January 2012
- Published by Springer Nature
- p. 323-359
Autonomous and Interoperable Smart Sensors for Environmental Monitoring Applications
- 1 October 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Standardization for interoperable autonomous smart sensors in the future energy grid system
A hierarchy to reach the interoperability of future smart energy grid system is proposed by introducing compliant levels in a pyramidal model. Interoperability layers in this approach was modeled using a button-top approach, from a technical level and standards, such as ZigBee or 6IoWPAN, with autonomous smart sensors to reach syntactic interoperability based on the IEEE 1451 standard. Also, the IEEE 1451 smart sensor model is defined taking into account a Network Capable Application Processor (NCAP), as coordinator node, and autonomous smart sensor nodes, Wireless Transducer Interface Module (WTIM) nodes, with sensing capabilities for cooperation with energy grid system, that employs the IEEE 1451 standard based on standard commands with header compression to decrease overall metadata information. Furthermore, this model could be extended in the future for small energy harvesting devices deployed in smart homes and energy utilities, to improve the efficiency, reliability and customer cost savings.
- 1 October 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Standardization for interoperable autonomous smart sensors in the future energy grid system
A hierarchy to reach the interoperability of future smart energy grid system is proposed by introducing compliant levels in a pyramidal model. Interoperability layers in this approach was modeled using a button-top approach, from a technical level and standards, such as ZigBee or 6IoWPAN, with autonomous smart sensors to reach syntactic interoperability based on the IEEE 1451 standard. Also, the IEEE 1451 smart sensor model is defined taking into account a Network Capable Application Processor (NCAP), as coordinator node, and autonomous smart sensor nodes, Wireless Transducer Interface Module (WTIM) nodes, with sensing capabilities for cooperation with energy grid system, that employs the IEEE 1451 standard based on standard commands with header compression to decrease overall metadata information. Furthermore, this model could be extended in the future for small energy harvesting devices deployed in smart homes and energy utilities, to improve the efficiency, reliability and customer cost savings.
- 5 May 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 60 (8) , 2751-2758
IEEE 1451 Standard in 6LoWPAN Sensor Networks Using a Compact Physical-Layer Transducer Electronic Datasheet
The adoption of the Internet Protocol version 6 (IPv6) networking in IEEE 802.15.4 sensor networks, using IEEE 1451 standardization, increases the interoperability of low-power smart-sensor devices over IP networks. This paper explains the design and implementation of the IPv6 sensor network over low-power wireless personal-area networks (6LoWPANs), and it uses the IEEE 1451 standard in IEEE 802.15.4 sensor networks. We propose the design of the 6LoWPAN physical-layer transducer electronic datasheet (PHY-TEDS) using data-type redefinition with the header compression. Each TEDS was analyzed in terms of memory size, obtaining a reduction of 48% in the PHY-TEDS and 25% in the meta-TEDS with respect to the standard definition. Finally, the IEEE 1451 commands are encapsulated in User Datagram Protocol datagrams to establish communication from the network capable application processor to the wireless transducer interface module in an environmental monitoring application.
- 5 May 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 60 (8) , 2751-2758
IEEE 1451 Standard in 6LoWPAN Sensor Networks Using a Compact Physical-Layer Transducer Electronic Datasheet
The adoption of the Internet Protocol version 6 (IPv6) networking in IEEE 802.15.4 sensor networks, using IEEE 1451 standardization, increases the interoperability of low-power smart-sensor devices over IP networks. This paper explains the design and implementation of the IPv6 sensor network over low-power wireless personal-area networks (6LoWPANs), and it uses the IEEE 1451 standard in IEEE 802.15.4 sensor networks. We propose the design of the 6LoWPAN physical-layer transducer electronic datasheet (PHY-TEDS) using data-type redefinition with the header compression. Each TEDS was analyzed in terms of memory size, obtaining a reduction of 48% in the PHY-TEDS and 25% in the meta-TEDS with respect to the standard definition. Finally, the IEEE 1451 commands are encapsulated in User Datagram Protocol datagrams to establish communication from the network capable application processor to the wireless transducer interface module in an environmental monitoring application.
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 183-186
Tiny and autonomous IEEE1451 Sonic Anemometer to deploy in environmental Wireless Sensor Network
Wind speed and direction are important parameters in the study of applied meteorology, for example, in weather prediction, air pollution, transport safety and structural safety. In this paper, we propose the design and deployment of an interoperable Smart Ultrasonic Anemometer that uses the IEEE 1451 standard and operates in a Wireless Sensor Network (WSN). This standard permits interoperability and introduces self-calibration and self-configuration tasks. We include power management considerations to calculate the energy consumption using a low power sampling protocol BMAC with variable duty cycle. Experimental tests are included to study the current consumption using an energy harvester with solar panel and super capacitors to increase the reliability and lifetime of the sensor node.
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 183-186
Tiny and autonomous IEEE1451 Sonic Anemometer to deploy in environmental Wireless Sensor Network
Wind speed and direction are important parameters in the study of applied meteorology, for example, in weather prediction, air pollution, transport safety and structural safety. In this paper, we propose the design and deployment of an interoperable Smart Ultrasonic Anemometer that uses the IEEE 1451 standard and operates in a Wireless Sensor Network (WSN). This standard permits interoperability and introduces self-calibration and self-configuration tasks. We include power management considerations to calculate the energy consumption using a low power sampling protocol BMAC with variable duty cycle. Experimental tests are included to study the current consumption using an energy harvester with solar panel and super capacitors to increase the reliability and lifetime of the sensor node.
- 1 February 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 189-193
Understanding the IEEE 1451 standard in 6loWPAN sensor networks
The adoption of the IPv6 networking in IEEE 802.15.4 sensor networks, using IEEE 1451 standardization, increases the interoperability of low-power smart sensor devices in IP networks. This paper explains the design and implementation of IPv6 over Low power Wireless Personal Area Networks (6loWPAN) and it uses the IEEE 1451 standard over IEEE 802.15.4 sensor networks. We propose an application of API IEEE 1451 that uses web services to transmit IEEE 1451 commands between Network Capable Application Processor (NCAP) and Wireless Transducer Interface Module (WTIM) using the client-server architecture. In addition the design of 6loWPAN Physical Transducer Electronic Datasheet (PHY-TEDS) IEEE 1451.5 is explained. All TEDS were analyzed in terms of memory size. Each IEEE 1451 command is encapsulated in an UDP socket to establish NCAP-to-WTIM communication in an environmental monitoring application.
- 1 February 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 189-193
Understanding the IEEE 1451 standard in 6loWPAN sensor networks
The adoption of the IPv6 networking in IEEE 802.15.4 sensor networks, using IEEE 1451 standardization, increases the interoperability of low-power smart sensor devices in IP networks. This paper explains the design and implementation of IPv6 over Low power Wireless Personal Area Networks (6loWPAN) and it uses the IEEE 1451 standard over IEEE 802.15.4 sensor networks. We propose an application of API IEEE 1451 that uses web services to transmit IEEE 1451 commands between Network Capable Application Processor (NCAP) and Wireless Transducer Interface Module (WTIM) using the client-server architecture. In addition the design of 6loWPAN Physical Transducer Electronic Datasheet (PHY-TEDS) IEEE 1451.5 is explained. All TEDS were analyzed in terms of memory size. Each IEEE 1451 command is encapsulated in an UDP socket to establish NCAP-to-WTIM communication in an environmental monitoring application.
- 1 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 002269-002274
Outdoor testing of CPV modules in INTA-SPASOLAB according to IEC 62108
This paper describes the work carried out in INTA-SPASOLAB aimed at getting the accreditation to IEC-62108, which was approved in December 2007. The huge experience in both qualification and certification, accumulated in SPASOLAB-INTA has been used to prepare a full equipped testing field with two double-axes trackers and a meteorological station. As a result of this work, improvements to the current version of the standard have been proposed as well as new tests that should be considered in the following amendments. Reliability tests are also under development.
- 1 June 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 002269-002274
Outdoor testing of CPV modules in INTA-SPASOLAB according to IEC 62108
This paper describes the work carried out in INTA-SPASOLAB aimed at getting the accreditation to IEC-62108, which was approved in December 2007. The huge experience in both qualification and certification, accumulated in SPASOLAB-INTA has been used to prepare a full equipped testing field with two double-axes trackers and a meteorological station. As a result of this work, improvements to the current version of the standard have been proposed as well as new tests that should be considered in the following amendments. Reliability tests are also under development.