Vishnu Prasad Muddineni
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Vishnu Prasad Muddineni has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Srinivasa Rao Sandepudi
National Institute of Technology,Dept. of Electrical Engineering,Warangal,India
12 shared publications- Anil Kumar Bonala
Department of Electrical Engineering National Institute of Technology Warangal India
11 shared publications Anil Kumar Bonala
Vaagdevi College of Engineering
4 shared publicationsHareesh Kumar Yada
Vaagdevi College of Engineering
2 shared publicationsAvudayappan Naraina
JAYAMUKHI INSTITUTE OF TECHNOLOGICAL SCIENCES
1 shared publication- Srinivasa Rao Sandepudi
Department of Electrical Engineering, National Institute of Technology Warangal
1 shared publication
Latest Publications
- 7 February 2023
- Published by Springer Nature
- p. 31-44
Dynamic Weighting Selection for Predictive Torque and Flux Control of Industrial Drives
- 7 February 2023
- Published by Springer Nature
- p. 31-44
Dynamic Weighting Selection for Predictive Torque and Flux Control of Industrial Drives
- 27 February 2021
- Published by Springer Nature
- p. 1165-1179
Implementation of Predictive Control Techniques Using PLEXIM Tool
- 27 February 2021
- Published by Springer Nature
- p. 1165-1179
Implementation of Predictive Control Techniques Using PLEXIM Tool
- 1 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (1) , 835-844
Grey Relational Analysis-Based Objective Function Optimization for Predictive Torque Control of Induction Machine
This paper presents Grey Relational Analysis (GRA) based objective function optimization in Predictive Torque Control (PTC) for induction machine. Selection of appropriate weighting factor in the objective function is one of the key aspects in the implementation of PTC. However, selection of suitable weighting factor in the objective function is a heuristic task. To address this issue, Grey Relational Analysis (GRA) method is implemented in the objective function optimization. In this approach, single objective function is modified into two independent objective functions for stator flux and torque. A Grey Relational Grade (GRG) is used to identify the suitable control action in each sampling. A MATLAB/Simulink model is developed to validate the control algorithm under various operating conditions of the drive and corresponding results are compared with experimental results.
- 1 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (1) , 835-844
Grey Relational Analysis-Based Objective Function Optimization for Predictive Torque Control of Induction Machine
This paper presents Grey Relational Analysis (GRA) based objective function optimization in Predictive Torque Control (PTC) for induction machine. Selection of appropriate weighting factor in the objective function is one of the key aspects in the implementation of PTC. However, selection of suitable weighting factor in the objective function is a heuristic task. To address this issue, Grey Relational Analysis (GRA) method is implemented in the objective function optimization. In this approach, single objective function is modified into two independent objective functions for stator flux and torque. A Grey Relational Grade (GRG) is used to identify the suitable control action in each sampling. A MATLAB/Simulink model is developed to validate the control algorithm under various operating conditions of the drive and corresponding results are compared with experimental results.
- 8 September 2020
- Published by Springer Nature
- p. 1215-1223
Sequential Selection-Based Predictive Direct Torque Control for Cascaded H-Bridge Inverter-Driven Induction Motor Drive
- 8 September 2020
- Published by Springer Nature
- p. 1215-1223
Sequential Selection-Based Predictive Direct Torque Control for Cascaded H-Bridge Inverter-Driven Induction Motor Drive
- 1 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Grey Relational Analysis based objective Function Optimization for Predictive Torque Control of Induction Machine
This paper presents a modified objective function optimization for Predictive Torque Control (PTC) of induction machine based on Grey Relational Analysis (GRA) method. PTC offers better steady state and dynamic operating conditions on proper selection of weighing factor in the objective function. However, selection of appropriate weighting factor in the objective function is a heuristic task. To address this issue, Grey Relational Analysis (GRA) method is implemented in the objective function optimization to overcome the problems associated with weighting factor selection. In this approach, single objective function is modified into two independent objective functions for stator flux and torque. A grey relational grade is used to identify the suitable control action in each sampling. A MATLAB/Simulink model is developed to validate the control algorithm under various operating conditions and corresponding results are compared with experimental results.
- 1 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Grey Relational Analysis based objective Function Optimization for Predictive Torque Control of Induction Machine
This paper presents a modified objective function optimization for Predictive Torque Control (PTC) of induction machine based on Grey Relational Analysis (GRA) method. PTC offers better steady state and dynamic operating conditions on proper selection of weighing factor in the objective function. However, selection of appropriate weighting factor in the objective function is a heuristic task. To address this issue, Grey Relational Analysis (GRA) method is implemented in the objective function optimization to overcome the problems associated with weighting factor selection. In this approach, single objective function is modified into two independent objective functions for stator flux and torque. A grey relational grade is used to identify the suitable control action in each sampling. A MATLAB/Simulink model is developed to validate the control algorithm under various operating conditions and corresponding results are compared with experimental results.
- Open Access
- 4 September 2018
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 11 (13) , 2072-2080
Selective finite‐states model predictive control of grid interfaced three‐level neutral point clamped photovoltaic inverter for inherent capacitor voltage balancing
A selective finite states model predictive control is proposed for a grid interfaced three‐level neutral point clamped solar photovoltaic inverter. The proposed control approach eliminates the weighting factor selection for dc‐link capacitor voltage balancing and reduces the computational burden for real‐time implementation. The switching states required for the prediction and objective function optimisation are selected based on the position of reference voltage vector in the space vector plane, inverter current directions and the charge status of the dc‐link capacitors. As a result, the selection of optimal switching state is fast, easy to implement and eliminates the selection of weighting factor for capacitor voltage balancing. The feasibility of the proposed control approach is verified through simulation and laboratory‐scale experimentation. The results confirm that the proposed method attains the inherent dc‐link capacitor voltage balance and also retains the dynamic and steady‐state current tracking in comparison with the classical finite control‐set model predictive control.
- 4 September 2018
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 11 (13) , 2072-2080
Open AccessSelective finite‐states model predictive control of grid interfaced three‐level neutral point clamped photovoltaic inverter for inherent capacitor voltage balancing
A selective finite states model predictive control is proposed for a grid interfaced three‐level neutral point clamped solar photovoltaic inverter. The proposed control approach eliminates the weighting factor selection for dc‐link capacitor voltage balancing and reduces the computational burden for real‐time implementation. The switching states required for the prediction and objective function optimisation are selected based on the position of reference voltage vector in the space vector plane, inverter current directions and the charge status of the dc‐link capacitors. As a result, the selection of optimal switching state is fast, easy to implement and eliminates the selection of weighting factor for capacitor voltage balancing. The feasibility of the proposed control approach is verified through simulation and laboratory‐scale experimentation. The results confirm that the proposed method attains the inherent dc‐link capacitor voltage balance and also retains the dynamic and steady‐state current tracking in comparison with the classical finite control‐set model predictive control.
- 9 August 2017
- Published by Taylor & Francis in Electric Power Components and Systems
- Vol. 45 (13) , 1450-1462
Improved Weighting Factor Selection for Predictive Torque Control of Induction Motor Drive Based on a Simple Additive Weighting Method
A predictive torque control (PTC) technique is emerging as an effective alternative for induction motor drives because of its simple structure, ability to include control parameters directly into the cost function, and fast dynamic response. To implement PTC for induction motor drive, both stator flux and torque errors are predicted for each switching state of the converter and the combined error is determined with the help of cost function using a suitable stator flux weighting factor. However, the selection of suitable weighting factor is a tedious and complex task. In this paper, a simple additive weighting method is introduced in the cost function optimization to simplify the weighting factor selection process. To observe the effectiveness of the proposed control algorithm, both simulation and experimental results are presented for a two-level voltage-source-inverter-fed induction motor drive and compared with conventional PTC under various operating conditions. The proposed control technique achieves low-torque ripple along with reduced switching frequency.
- 9 August 2017
- Published by Taylor & Francis in Electric Power Components and Systems
- Vol. 45 (13) , 1450-1462
Improved Weighting Factor Selection for Predictive Torque Control of Induction Motor Drive Based on a Simple Additive Weighting Method
A predictive torque control (PTC) technique is emerging as an effective alternative for induction motor drives because of its simple structure, ability to include control parameters directly into the cost function, and fast dynamic response. To implement PTC for induction motor drive, both stator flux and torque errors are predicted for each switching state of the converter and the combined error is determined with the help of cost function using a suitable stator flux weighting factor. However, the selection of suitable weighting factor is a tedious and complex task. In this paper, a simple additive weighting method is introduced in the cost function optimization to simplify the weighting factor selection process. To observe the effectiveness of the proposed control algorithm, both simulation and experimental results are presented for a two-level voltage-source-inverter-fed induction motor drive and compared with conventional PTC under various operating conditions. The proposed control technique achieves low-torque ripple along with reduced switching frequency.
- Open Access
- 1 May 2017
- Published by Institution of Engineering and Technology (IET) in IET Electric Power Applications
- Vol. 11 (5) , 749-760
Finite control set predictive torque control for induction motor drive with simplified weighting factor selection using TOPSIS method
Finite control set predictive torque control (FCS‐PTC) becomes popular for induction motor drives due to its simple structure and flexibility of including additional control parameters into the control law. However, primary concern of this control technique is the selection of suitable weighting factors in the cost‐function. Usually, empirical method is used to select the weighting factors, which is time‐consuming and heuristic process. In this study, Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) method is introduced in the cost‐function optimization to simplify the difficulties involved in the weighting factor selection. This method selects an optimal control action, which is closer to positive ideal control action and far away from negative ideal control action. This ensures the selection of optimal control action in each sampling period based on the priorities given to control parameters in the cost‐function. Further, to reduce the computational burden of proposed technique, a predefined set of switching states are used for the cost‐function optimization based on previous optimal control action. Both simulation and experimental studies are carried out for a two‐level voltage source inverter fed induction motor drive. These results are compared with conventional FCS‐PTC technique to highlight the merits of proposed technique.
- 1 May 2017
- Published by Institution of Engineering and Technology (IET) in IET Electric Power Applications
- Vol. 11 (5) , 749-760
Open AccessFinite control set predictive torque control for induction motor drive with simplified weighting factor selection using TOPSIS method
Finite control set predictive torque control (FCS‐PTC) becomes popular for induction motor drives due to its simple structure and flexibility of including additional control parameters into the control law. However, primary concern of this control technique is the selection of suitable weighting factors in the cost‐function. Usually, empirical method is used to select the weighting factors, which is time‐consuming and heuristic process. In this study, Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) method is introduced in the cost‐function optimization to simplify the difficulties involved in the weighting factor selection. This method selects an optimal control action, which is closer to positive ideal control action and far away from negative ideal control action. This ensures the selection of optimal control action in each sampling period based on the priorities given to control parameters in the cost‐function. Further, to reduce the computational burden of proposed technique, a predefined set of switching states are used for the cost‐function optimization based on previous optimal control action. Both simulation and experimental studies are carried out for a two‐level voltage source inverter fed induction motor drive. These results are compared with conventional FCS‐PTC technique to highlight the merits of proposed technique.
- 1 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Model predictive current control with modified synchronous detection technique for three-phase 3L-NPC multi-functional solar photovoltaic system
In this paper, a model based predictive current control (MPCC) with a modified synchronous detection technique (SDT) is developed for a 3L-NPC multi-functional inverter based solar photovoltaic (SPV) system. This 3L-NPC multi-functional grid tied inverter (MFGTI) perform maximum power point tracking, harmonic compensation, load balancing and power factor control. The proposed SDT consists of two-stages, fundamental component of sensed voltage is extracted using three 1-ph enhanced phase locked loops (EPLL) in the first stage, where as in the second stage, the reactive power injection is controlled by controlling the phase of the injecting currents to operate the point of common coupling (PCC) at the desired power factor. In order to achieve a fast dynamic control, a MPCC is employed for MFGTI. The discrete-time model of three-phase/3L-NPC MFGTI is used to predict the compensation currents for the possible 27 switching-states. The optimal switching-state that minimizes the objective-function is applied in the next sampling instant. The proposed control approach provides fast dynamic response for sudden change in active and reactive powers, high current tracking performance. Simulations are carried out using Matlab/Simulink and the results are presented to highlight the effectiveness of the proposed control technique.
- 1 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Model predictive current control with modified synchronous detection technique for three-phase 3L-NPC multi-functional solar photovoltaic system
In this paper, a model based predictive current control (MPCC) with a modified synchronous detection technique (SDT) is developed for a 3L-NPC multi-functional inverter based solar photovoltaic (SPV) system. This 3L-NPC multi-functional grid tied inverter (MFGTI) perform maximum power point tracking, harmonic compensation, load balancing and power factor control. The proposed SDT consists of two-stages, fundamental component of sensed voltage is extracted using three 1-ph enhanced phase locked loops (EPLL) in the first stage, where as in the second stage, the reactive power injection is controlled by controlling the phase of the injecting currents to operate the point of common coupling (PCC) at the desired power factor. In order to achieve a fast dynamic control, a MPCC is employed for MFGTI. The discrete-time model of three-phase/3L-NPC MFGTI is used to predict the compensation currents for the possible 27 switching-states. The optimal switching-state that minimizes the objective-function is applied in the next sampling instant. The proposed control approach provides fast dynamic response for sudden change in active and reactive powers, high current tracking performance. Simulations are carried out using Matlab/Simulink and the results are presented to highlight the effectiveness of the proposed control technique.
- 1 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Improved model predictive current control for single-phase NPC shunt active power filter
A model predictive current control (MPCC) of shunt active power filter (SAPF) requires tracking of distorted reference current based on the discrete mathematical model of the system. But the approximations considered in the development of mathematical model for the nonlinear system and also the uncertainty in the parameter values will deteriorate the performance of control algorithm. To enhance the current tracking performance, an improved MPCC for single-phase NPC converter based SAPF is presented in this paper. In the proposed control strategy, a mean squared predictive current error is used as a feedback in current tracking objective of the cost function. The optimal switching vector that minimizes the defined cost function is applied in the next sampling period. The robustness of the proposed control strategy for variation in grid feeder impedance and interfacing filter inductance is verified using matlab/simulink results. The results presented are compared with MPCC for absolute current tracking error and the percentage of total harmonic distortion (%THD).
- 1 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Improved model predictive current control for single-phase NPC shunt active power filter
A model predictive current control (MPCC) of shunt active power filter (SAPF) requires tracking of distorted reference current based on the discrete mathematical model of the system. But the approximations considered in the development of mathematical model for the nonlinear system and also the uncertainty in the parameter values will deteriorate the performance of control algorithm. To enhance the current tracking performance, an improved MPCC for single-phase NPC converter based SAPF is presented in this paper. In the proposed control strategy, a mean squared predictive current error is used as a feedback in current tracking objective of the cost function. The optimal switching vector that minimizes the defined cost function is applied in the next sampling period. The robustness of the proposed control strategy for variation in grid feeder impedance and interfacing filter inductance is verified using matlab/simulink results. The results presented are compared with MPCC for absolute current tracking error and the percentage of total harmonic distortion (%THD).