Yabo Fu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yabo Fu has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Changhong Lin
International Joint Institute of Advanced Coating Technology, Taizhou University, Taizhou 318000, China
2 shared publications - Jianbo Wu
School of Materials Science and Engineering, Taizhou University, Taizhou 318000, China
2 shared publications Jinchuan Jie
2 shared publicationsJing Cui
Civil Aviat Univ China, Sch Airport, Tianjin 30300, Peoples R China
2 shared publicationsRenqing Guo
Zhejiang Provincial Key Laboratory for Cutting Tools, Taizhou University, Taizhou, People’s Republic of China
2 shared publicationsShufeng Li
School of Materials Science and Engineering, Xi’an University of Technology, Xi’an, People’s Republic of China
2 shared publications
Latest Publications
- Open Access
- 19 January 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 41, 2252-2262
Pathway to lead-free brass by stabilizing graphite via TiC-β phase interface
- 19 January 2026
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 41, 2252-2262
Open AccessPathway to lead-free brass by stabilizing graphite via TiC-β phase interface
- Top Cited PapersOpen Access
- 26 December 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 34, 2127-2132
Twinning and stacking fault-induced precipitation in an aluminum alloy
- 26 December 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 34, 2127-2132
Top Cited PapersOpen AccessTwinning and stacking fault-induced precipitation in an aluminum alloy
- Open Access
- 31 August 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (9) , 306
Microstructure, Mechanical and Tribological Properties of Cu40Zn-Ti3AlC2 Composites by Powder Metallurgy
The exploration of unleaded free-cutting Cu40Zn brass with excellent mechanical and tribological properties has always drawn the attention of researchers. Due to its attractive properties combining metals and ceramics, Ti3AlC2 was added to Cu40Zn brass using high-energy milling and hot-pressing sintering. The effects of Ti3AlC2 on the microstructure, mechanical and tribological properties of Cu40Zn-Ti3AlC2 composites were studied. The results showed that Ti3AlC2 could suppress the formation of ZnO by adsorbing oxygen impurity and promote the formation of the β phase by releasing the β-forming element Al to the substrate. The hardness and wear resistance of Cu40Zn-Ti3AlC2 composites increased with increasing Ti3AlC2 content from 0 to 5 wt.%. The proper Ti3AlC2 additive was beneficial to both the strength and plasticity of the composites. The underlying mechanisms were discussed.
- 31 August 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (9) , 306
Open AccessMicrostructure, Mechanical and Tribological Properties of Cu40Zn-Ti3AlC2 Composites by Powder Metallurgy
The exploration of unleaded free-cutting Cu40Zn brass with excellent mechanical and tribological properties has always drawn the attention of researchers. Due to its attractive properties combining metals and ceramics, Ti3AlC2 was added to Cu40Zn brass using high-energy milling and hot-pressing sintering. The effects of Ti3AlC2 on the microstructure, mechanical and tribological properties of Cu40Zn-Ti3AlC2 composites were studied. The results showed that Ti3AlC2 could suppress the formation of ZnO by adsorbing oxygen impurity and promote the formation of the β phase by releasing the β-forming element Al to the substrate. The hardness and wear resistance of Cu40Zn-Ti3AlC2 composites increased with increasing Ti3AlC2 content from 0 to 5 wt.%. The proper Ti3AlC2 additive was beneficial to both the strength and plasticity of the composites. The underlying mechanisms were discussed.
- 12 February 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (3) , 2017-2027
A Novel Microstructure of Cu-Ti Alloy with Ultrahigh Electrical Conductivity and Strength
- 12 February 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (3) , 2017-2027
A Novel Microstructure of Cu-Ti Alloy with Ultrahigh Electrical Conductivity and Strength
- 27 December 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (19) , 8904-8912
Enhancing Compressive Stress–Strain of Ti55531 Alloy via La-Rich Nanoscale Structure at Grain Boundaries
- 27 December 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (19) , 8904-8912
Enhancing Compressive Stress–Strain of Ti55531 Alloy via La-Rich Nanoscale Structure at Grain Boundaries
- 6 September 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (7) , 1-10
Gradient Structure of Ti-55531 with Nano-ultrafine Grains Fabricated by Simulation and Suction Casting
- 6 September 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (7) , 1-10
Gradient Structure of Ti-55531 with Nano-ultrafine Grains Fabricated by Simulation and Suction Casting
- Open Access
Investigation of the Adhesion Strength, Fracture Toughness, and Stability of M/Cr2N and M/V2N (M = Ti, Ru, Ni, Pd, Al, Ag, and Cu) Interfaces Based on First-Principles Calculations
Obtaining detailed information regarding the interfacial characteristics of metal/hexagonal-TMN composites is imperative for developing these materials with optimal mechanical properties. To this end, we systematically investigate the work of adhesion, fracture toughness, and interfacial stability of M/Cr2N and M/V2N interfaces using first-principles calculations. The orientation (0001) of hexagonal phases and (111) of fcc phases are selected as the interface orientations. Accordingly, we construct M/Cr2N interface models by considering 1N, 2N, and Cr terminations of Cr2N(0001), as well as two stacking sequences (top and hollow sites) for the 1N- and 2N-terminated interface models, respectively. The M/V2N interface models are constructed in the same way. The V-terminated Ni/V2N interface is demonstrated to provide a good combination of the work of adhesion, fracture toughness, and interfacial stability. Therefore, the Ni/V2N interface model can be regarded as the preferred configuration among the metal/hexagonal-TMN interface models considered. The present results offer a practical perspective for tailoring the interfaces in metal/hexagonal-TMN composite materials to obtain improved mechanical properties.
Open AccessInvestigation of the Adhesion Strength, Fracture Toughness, and Stability of M/Cr2N and M/V2N (M = Ti, Ru, Ni, Pd, Al, Ag, and Cu) Interfaces Based on First-Principles Calculations
Obtaining detailed information regarding the interfacial characteristics of metal/hexagonal-TMN composites is imperative for developing these materials with optimal mechanical properties. To this end, we systematically investigate the work of adhesion, fracture toughness, and interfacial stability of M/Cr2N and M/V2N interfaces using first-principles calculations. The orientation (0001) of hexagonal phases and (111) of fcc phases are selected as the interface orientations. Accordingly, we construct M/Cr2N interface models by considering 1N, 2N, and Cr terminations of Cr2N(0001), as well as two stacking sequences (top and hollow sites) for the 1N- and 2N-terminated interface models, respectively. The M/V2N interface models are constructed in the same way. The V-terminated Ni/V2N interface is demonstrated to provide a good combination of the work of adhesion, fracture toughness, and interfacial stability. Therefore, the Ni/V2N interface model can be regarded as the preferred configuration among the metal/hexagonal-TMN interface models considered. The present results offer a practical perspective for tailoring the interfaces in metal/hexagonal-TMN composite materials to obtain improved mechanical properties.
- Open Access
Effect of CeO2 Nanoparticles on Interface of Cu/Al2O3 Ceramic Clad Composites
Cu/Al2O3 ceramic clad composites are widely used in electronic packaging and electrical contacts. However, the conductivity and strength of the interfacial layer are not fit for the demands. So CeO2 nanoparticles 24.3 nm in size, coated on Al2O3 ceramic, promote a novel CeO2–Cu2O–Cu system to improve the interfacial bonded strength. Results show that the atom content of O is increased to approximately 30% with the addition of CeO2 nanoparticles compared with the atom content without CeO2 in the interfacial layer of Cu/Al2O3 ceramic clad composites. CeO2 nanoparticles coated on the surface of Al2O3 ceramics can easily diffuse into the metallic Cu layer. CeO2 nanoparticles can accelerate to form the eutectic liquid of Cu2O–Cu as they have strong functions of storing and releasing O at an Ar pressure of 0.12 MPa. The addition of CeO2 nanoparticles is beneficial for promoting the bonded strength of the Cu/Al2O3 ceramic clad composites. The bonded strength of the interface coated with nanoparticles of CeO2 is increased to 20.8% compared with that without CeO2; moreover, the electric conductivity on the side of metallic Cu is 95% IACS. The study is of great significance for improving properties of Cu/Al2O3 ceramic clad composites.
Open AccessEffect of CeO2 Nanoparticles on Interface of Cu/Al2O3 Ceramic Clad Composites
Cu/Al2O3 ceramic clad composites are widely used in electronic packaging and electrical contacts. However, the conductivity and strength of the interfacial layer are not fit for the demands. So CeO2 nanoparticles 24.3 nm in size, coated on Al2O3 ceramic, promote a novel CeO2–Cu2O–Cu system to improve the interfacial bonded strength. Results show that the atom content of O is increased to approximately 30% with the addition of CeO2 nanoparticles compared with the atom content without CeO2 in the interfacial layer of Cu/Al2O3 ceramic clad composites. CeO2 nanoparticles coated on the surface of Al2O3 ceramics can easily diffuse into the metallic Cu layer. CeO2 nanoparticles can accelerate to form the eutectic liquid of Cu2O–Cu as they have strong functions of storing and releasing O at an Ar pressure of 0.12 MPa. The addition of CeO2 nanoparticles is beneficial for promoting the bonded strength of the Cu/Al2O3 ceramic clad composites. The bonded strength of the interface coated with nanoparticles of CeO2 is increased to 20.8% compared with that without CeO2; moreover, the electric conductivity on the side of metallic Cu is 95% IACS. The study is of great significance for improving properties of Cu/Al2O3 ceramic clad composites.
- 1 August 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 798, 616-621
Strength and electrical conductivity behavior of nanoparticles reaction on new alumina dispersion-strengthened copper alloy
- 1 August 2019
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 798, 616-621
Strength and electrical conductivity behavior of nanoparticles reaction on new alumina dispersion-strengthened copper alloy
- 1 May 2018
- Published by American Scientific Publishers in Science of Advanced Materials
- Vol. 10 (5) , 718-723
Al2O3 Nanoparticles Induced Corrosion Behavior of Copper-Based Composites in a Chloride Environment
Highly corrosion resistant copper-based composites with a uniform distribution of Al2O3 nanoparticles were fabricated by mechanical alloying combined with electromagnetic stirring solidification. Results indicate that Al2O3 nanoparticles can enhance the corrosion resistance of copper-based composites in chloride environment. The highest corrosion resistance is gained by the addition of 0.10 wt% Al2O3 nanoparticles. A new protection film (Cu-Al2O3) is formed by the Al2O3 nanoparticles coupling with Cu. With the addition of 0.10 wt% Al2O3 nanoparticles, this protection film can achieve a uniform distribution of the nanoparticles around copper grains by electromagnetic stirring. Charge carrier current is decreased between the copper grains and clusters, and controlling equilibrium velocities in generating a thicker protecting film is easy in the NaCl solution; therefore, the corrosion resistance is enhanced. No further improvements in corrosion resistance are seen in composites beyond 0.10 wt% Al2O3 nanoparticle contents.
- 1 May 2018
- Published by American Scientific Publishers in Science of Advanced Materials
- Vol. 10 (5) , 718-723
Al2O3 Nanoparticles Induced Corrosion Behavior of Copper-Based Composites in a Chloride Environment
Highly corrosion resistant copper-based composites with a uniform distribution of Al2O3 nanoparticles were fabricated by mechanical alloying combined with electromagnetic stirring solidification. Results indicate that Al2O3 nanoparticles can enhance the corrosion resistance of copper-based composites in chloride environment. The highest corrosion resistance is gained by the addition of 0.10 wt% Al2O3 nanoparticles. A new protection film (Cu-Al2O3) is formed by the Al2O3 nanoparticles coupling with Cu. With the addition of 0.10 wt% Al2O3 nanoparticles, this protection film can achieve a uniform distribution of the nanoparticles around copper grains by electromagnetic stirring. Charge carrier current is decreased between the copper grains and clusters, and controlling equilibrium velocities in generating a thicker protecting film is easy in the NaCl solution; therefore, the corrosion resistance is enhanced. No further improvements in corrosion resistance are seen in composites beyond 0.10 wt% Al2O3 nanoparticle contents.