Aki Karttunen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Aki Karttunen has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Antti. V. Raisanen
Department of Electronics and Nanoengineering, Aalto University, Espoo, Finland
3 shared publications - Katsuyuki Haneda
Department of Electronics and Nanoengineering, Aalto University School of Electrical Engineering, Espoo, Finland
3 shared publications - Ville Viikari
Aalto University
3 shared publications Andreas F. Molisch
Department of Electrical Engineering, University of Southern California, Los Angeles, CA, USA
2 shared publications- Jan Jarvelainen
Premix Oy, FI-05200 Rajamäki, Finland
2 shared publications Juha Ala-Laurinaho
Department of Electronics and Nanoengineering, Aalto University, Espoo, FI, Finland
2 shared publications
Latest Publications
- Open Access
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Wireless Communications
- Vol. 24 (11) , 8952-8968
Idle-Mode Positioning in mmWave Cellular Networks Through Beam-Level Path Loss Measurements Without LOS Detection
Positioning is a vital capability in different radio systems for extracting situational awareness, with path loss (PL)-based positioning playing a crucial role due to its widespread use in wireless standards. In this work, we propose an idle-mode PL-based positioning approach without line-of-sight (LOS) detection that is suitable for millimeter-wave (mmWave) urban networks with directive beams in the base stations (BSs). With the beam gain significantly affecting the observed PLs, we divide the data and models relative to the beam direction rather than to LOS and non-line-of-sight (NLOS) BSs. Different approaches for obtaining the PL model parameter estimates are proposed, including model fitting taking into account the influence of the noise limit and direct optimization based on positioning accuracy using the training data set. In addition to the PLs, azimuth- and elevation-of-departure (AoD and EoD) are estimated, modeled, and used in the positioning calculations, building on maximum likelihood (ML) estimation. Comprehensive numerical results and performance assessments are provided, harnessing ray-tracing (RT) data in a 28GHz urban microcellular environment. The demonstrated median positioning error is under 20m reflecting an improvement of 50%-70% compared to the classical CellID method. Additionally, the results show that the proposed method outperforms machine learning based reference solutions. Finally, the methods and the resulting positioning performance are shown to be robust against variations in the underlying technical parameters, such as the BS transmit beam-width, as well as errors or imperfections in the assumed BS locations and BS orientation information.
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Wireless Communications
- Vol. 24 (11) , 8952-8968
Open AccessIdle-Mode Positioning in mmWave Cellular Networks Through Beam-Level Path Loss Measurements Without LOS Detection
Positioning is a vital capability in different radio systems for extracting situational awareness, with path loss (PL)-based positioning playing a crucial role due to its widespread use in wireless standards. In this work, we propose an idle-mode PL-based positioning approach without line-of-sight (LOS) detection that is suitable for millimeter-wave (mmWave) urban networks with directive beams in the base stations (BSs). With the beam gain significantly affecting the observed PLs, we divide the data and models relative to the beam direction rather than to LOS and non-line-of-sight (NLOS) BSs. Different approaches for obtaining the PL model parameter estimates are proposed, including model fitting taking into account the influence of the noise limit and direct optimization based on positioning accuracy using the training data set. In addition to the PLs, azimuth- and elevation-of-departure (AoD and EoD) are estimated, modeled, and used in the positioning calculations, building on maximum likelihood (ML) estimation. Comprehensive numerical results and performance assessments are provided, harnessing ray-tracing (RT) data in a 28GHz urban microcellular environment. The demonstrated median positioning error is under 20m reflecting an improvement of 50%-70% compared to the classical CellID method. Additionally, the results show that the proposed method outperforms machine learning based reference solutions. Finally, the methods and the resulting positioning performance are shown to be robust against variations in the underlying technical parameters, such as the BS transmit beam-width, as well as errors or imperfections in the assumed BS locations and BS orientation information.
- Open Access
Influence of Noise-Limited Censored Path Loss on Model Fitting and Path Loss-Based Positioning
Positioning is considered one of the key features in various novel industry verticals in future radio systems. Since path loss (PL) or received signal strength-based measurements are widely available in the majority of wireless standards, PL-based positioning has an important role among positioning technologies. Conventionally, PL-based positioning has two phases—fitting a PL model to training data and positioning based on the link distance estimates. However, in both phases, the maximum measurable PL is limited by measurement noise. Such immeasurable samples are called censored PL data and such noisy data are commonly neglected in both the model fitting and in the positioning phase. In the case of censored PL, the loss is known to be above a known threshold level and that information can be used in model fitting and in the positioning phase. In this paper, we examine and propose how to use censored PL data in PL model-based positioning. Additionally, we demonstrate with several simulations the potential of the proposed approach for considerable improvements in positioning accuracy (23–57%) and improved robustness against PL model fitting errors.
Open AccessInfluence of Noise-Limited Censored Path Loss on Model Fitting and Path Loss-Based Positioning
Positioning is considered one of the key features in various novel industry verticals in future radio systems. Since path loss (PL) or received signal strength-based measurements are widely available in the majority of wireless standards, PL-based positioning has an important role among positioning technologies. Conventionally, PL-based positioning has two phases—fitting a PL model to training data and positioning based on the link distance estimates. However, in both phases, the maximum measurable PL is limited by measurement noise. Such immeasurable samples are called censored PL data and such noisy data are commonly neglected in both the model fitting and in the positioning phase. In the case of censored PL, the loss is known to be above a known threshold level and that information can be used in model fitting and in the positioning phase. In this paper, we examine and propose how to use censored PL data in PL model-based positioning. Additionally, we demonstrate with several simulations the potential of the proposed approach for considerable improvements in positioning accuracy (23–57%) and improved robustness against PL model fitting errors.
- 6 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 69 (2) , 1227-1236
Characterizing Radio Wave Propagation in Urban Street Canyon With Vehicular Blockage at 28 GHz
The communications between two driving vehicles along a narrow street may be limited by the presence of a third vehicle blocking the transmission. In this work, we investigate radio wave propagation at 28 GHz in an urban street canyon scenario by conducting channel measurements, where the vehicle(s) occlude(s) the line-of-sight path. We quantify the impact of the car blockage and study the alternative propagation paths, which can be used for establishing a data link. Based on the obtained results, we report that besides the low-loss (3.4 dB) reflection from the wall, a radio link through the blocking car may potentially be established for data sharing. Specifically, the attenuation through clear windows is 2 dB, while the attenuation caused by protective sun film is 15 dB. Diffraction over the car and propagation in foliage reduce the multipath power crucially by 21-24 dB and 16-19 dB, respectively, and cannot be associated with reliable links. Finally, measurement results were compared with the ray-based simulation data, which demonstrates agreement to within +/- 4.3 dB of measured losses.
- 6 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 69 (2) , 1227-1236
Characterizing Radio Wave Propagation in Urban Street Canyon With Vehicular Blockage at 28 GHz
The communications between two driving vehicles along a narrow street may be limited by the presence of a third vehicle blocking the transmission. In this work, we investigate radio wave propagation at 28 GHz in an urban street canyon scenario by conducting channel measurements, where the vehicle(s) occlude(s) the line-of-sight path. We quantify the impact of the car blockage and study the alternative propagation paths, which can be used for establishing a data link. Based on the obtained results, we report that besides the low-loss (3.4 dB) reflection from the wall, a radio link through the blocking car may potentially be established for data sharing. Specifically, the attenuation through clear windows is 2 dB, while the attenuation caused by protective sun film is 15 dB. Diffraction over the car and propagation in foliage reduce the multipath power crucially by 21-24 dB and 16-19 dB, respectively, and cannot be associated with reliable links. Finally, measurement results were compared with the ray-based simulation data, which demonstrates agreement to within +/- 4.3 dB of measured losses.
- Open Access
Path Loss Characterization for Intra-Vehicle Wearable Deployments at 60 GHz
In this work, we present the results of a wideband measurement campaign at 60 GHz conducted inside a Linkker electric city bus. Targeting prospective millimeter-wave (mmWave) public transportation wearable scenarios, we mimic a typical deployment of mobile high-end consumer devices in a dense environment. Specifically, our intra-vehicle deployment includes one receiver and multiple transmitters corresponding to a mmWave access point and passengers' wearable and hand-held devices. While the receiver is located in the front part of the bus, the transmitters repeat realistic locations of personal devices (i) at the seat level (e.g., a hand-held device) and (ii) at a height 70 cm above the seat (e.g., a wearable device: augmented reality glasses or a head-mounted display). Based on the measured received power, we construct a logarithmic model for the distance-dependent path loss. The parametrized models developed in the course of this study have the potential to become an attractive ground for the link budget estimation and interference footprint studies in crowded public transportation scenarios.
Open AccessPath Loss Characterization for Intra-Vehicle Wearable Deployments at 60 GHz
In this work, we present the results of a wideband measurement campaign at 60 GHz conducted inside a Linkker electric city bus. Targeting prospective millimeter-wave (mmWave) public transportation wearable scenarios, we mimic a typical deployment of mobile high-end consumer devices in a dense environment. Specifically, our intra-vehicle deployment includes one receiver and multiple transmitters corresponding to a mmWave access point and passengers' wearable and hand-held devices. While the receiver is located in the front part of the bus, the transmitters repeat realistic locations of personal devices (i) at the seat level (e.g., a hand-held device) and (ii) at a height 70 cm above the seat (e.g., a wearable device: augmented reality glasses or a head-mounted display). Based on the measured received power, we construct a logarithmic model for the distance-dependent path loss. The parametrized models developed in the course of this study have the potential to become an attractive ground for the link budget estimation and interference footprint studies in crowded public transportation scenarios.
- 3 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 17 (10) , 1871-1875
Beam-Switching Dual-Spherical Lens Antenna With Low Scan Loss at 71–76 GHz
A millimeter-wave communication system needs a directive beam-steering antenna with a low scan loss to compensate the high free space loss. In this letter, an electronically beam-switching integrated lens antenna (ILA) system with low scan loss is designed for lower E-band (71-76 GHz). An ILA with hemispherical collimating surface of 26 mm radius and spherical feed surface of 37.5 mm radius is fabricated from Teflon material. A conformal 1 × 16 linear beam-switching feed array based on SP4T switches and Vivaldi antennas is designed. The maximum simulated and measured realized gain including the switch network losses is 21.8 and 19.6 dBi, respectively. The measured scan loss of the ILA excluding the switch network loss is less than 1.3 dB in the lower E-band for beams within $\pm$ 40°.- 3 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 17 (10) , 1871-1875
Beam-Switching Dual-Spherical Lens Antenna With Low Scan Loss at 71–76 GHz
A millimeter-wave communication system needs a directive beam-steering antenna with a low scan loss to compensate the high free space loss. In this letter, an electronically beam-switching integrated lens antenna (ILA) system with low scan loss is designed for lower E-band (71-76 GHz). An ILA with hemispherical collimating surface of 26 mm radius and spherical feed surface of 37.5 mm radius is fabricated from Teflon material. A conformal 1 × 16 linear beam-switching feed array based on SP4T switches and Vivaldi antennas is designed. The maximum simulated and measured realized gain including the switch network losses is 21.8 and 19.6 dBi, respectively. The measured scan loss of the ILA excluding the switch network loss is less than 1.3 dB in the lower E-band for beams within $\pm$ 40°.- Open Access
Modeling the Multipath Cross-Polarization Ratio for Above-6 GHz Radio Links
In this paper, we parameterize an excess loss-based multipath component (MPC) cross-polarization ratio (XPR) model in indoor and outdoor environments for above-6 GHz frequency bands. The results are based on 28 measurement campaigns in several frequency bands ranging from 15 to 80 GHz. A conventional XPR model of an MPC assuming a constant mean value fits our measurements very poorly and moreover overestimates the depolarization effect. Our measurements revealed a clear trend that the MPC XPR is inversely proportional to an excess loss in reference to the free-space path loss. The model is physically sound as a higher excess loss is attributed to more lossy interactions or to a greater number of interactions with objects, leading to a greater chance of depolarization. The measurements furthermore showed that the MPC XPR is not strongly frequency or environment dependent. In our MPC XPR model, an MPC with zero-dB excess loss has a mean XPR of 28 dB. The mean XPR decreases half-a-dB as the excess loss increases by every dB and the standard deviation around the mean is 6 dB. The model is applicable to existing channel models to reproduce realistic MPC XPRs for the above 6-GHz radio links.
Open AccessModeling the Multipath Cross-Polarization Ratio for Above-6 GHz Radio Links
In this paper, we parameterize an excess loss-based multipath component (MPC) cross-polarization ratio (XPR) model in indoor and outdoor environments for above-6 GHz frequency bands. The results are based on 28 measurement campaigns in several frequency bands ranging from 15 to 80 GHz. A conventional XPR model of an MPC assuming a constant mean value fits our measurements very poorly and moreover overestimates the depolarization effect. Our measurements revealed a clear trend that the MPC XPR is inversely proportional to an excess loss in reference to the free-space path loss. The model is physically sound as a higher excess loss is attributed to more lossy interactions or to a greater number of interactions with objects, leading to a greater chance of depolarization. The measurements furthermore showed that the MPC XPR is not strongly frequency or environment dependent. In our MPC XPR model, an MPC with zero-dB excess loss has a mean XPR of 28 dB. The mean XPR decreases half-a-dB as the excess loss increases by every dB and the standard deviation around the mean is 6 dB. The model is applicable to existing channel models to reproduce realistic MPC XPRs for the above 6-GHz radio links.
- Open Access
Comparing Radio Propagation Channels Between 28 and 140 GHz Bands in a Shopping Mall
In this paper, we compare the radio propagation channels characteristics between 28 and 140 GHz bands based on the wideband (several GHz) and directional channel sounding in a shopping mall environment. The measurements and data processing are conducted in such a way to meet requirements for a fair comparison of large- and small- scale channel parameters between the two bands. Our results reveal that there is high spatial-temporal correlation between 28 and 140 GHz channels, similar numbers of strong multipath components, and only small variations in the large-scale parameters between the two bands. Furthermore, when including the weak paths there are higher total numbers of clusters and paths in 28 GHz as compared to those in 140 GHz bands. With these similarities, it would be very interesting to investigate the potentials of using 140 GHz band in the future mobile radio communications.
Open AccessComparing Radio Propagation Channels Between 28 and 140 GHz Bands in a Shopping Mall
In this paper, we compare the radio propagation channels characteristics between 28 and 140 GHz bands based on the wideband (several GHz) and directional channel sounding in a shopping mall environment. The measurements and data processing are conducted in such a way to meet requirements for a fair comparison of large- and small- scale channel parameters between the two bands. Our results reveal that there is high spatial-temporal correlation between 28 and 140 GHz channels, similar numbers of strong multipath components, and only small variations in the large-scale parameters between the two bands. Furthermore, when including the weak paths there are higher total numbers of clusters and paths in 28 GHz as compared to those in 140 GHz bands. With these similarities, it would be very interesting to investigate the potentials of using 140 GHz band in the future mobile radio communications.
- Open Access
- 12 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Wireless Communications
- Vol. 16 (11) , 7538-7550
Spatially Consistent Street-by-Street Path Loss Model for 28-GHz Channels in Micro Cell Urban Environments
This paper considers a fundamental issue of path loss (PL) modeling in urban micro cell (UMi) environments, namely the spatial consistency of the model as the mobile station moves along a trajectory through street canyons. This paper is motivated by the observed non-stationarity of the PL. We show that the traditional model of power law PL plus log-normally distributed variations can provide misleading results that can have serious implications for system simulations. Rather, the PL parameters have to be modeled as random variables that change from street to street and also as a function of the street orientation. Variations of the PL, taken over the ensemble of the whole cell (or multiple cells), thus consist of the compound effect of these PL parameter variations together with the traditional shadowing variations along the trajectory of movement. Ray-tracing results demonstrate that ignoring this effect can lead to a severe overestimation of the local standard deviation in a given area. Then, a spatially consistent stochastic street-by-street PL model is established, and a parameterization for 28-GHz UMi cells is given. The model correctly describes the PL as a function of the street orientation as well as the large variance observed for all the PL model parameters.
- 12 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Wireless Communications
- Vol. 16 (11) , 7538-7550
Open AccessSpatially Consistent Street-by-Street Path Loss Model for 28-GHz Channels in Micro Cell Urban Environments
This paper considers a fundamental issue of path loss (PL) modeling in urban micro cell (UMi) environments, namely the spatial consistency of the model as the mobile station moves along a trajectory through street canyons. This paper is motivated by the observed non-stationarity of the PL. We show that the traditional model of power law PL plus log-normally distributed variations can provide misleading results that can have serious implications for system simulations. Rather, the PL parameters have to be modeled as random variables that change from street to street and also as a function of the street orientation. Variations of the PL, taken over the ensemble of the whole cell (or multiple cells), thus consist of the compound effect of these PL parameter variations together with the traditional shadowing variations along the trajectory of movement. Ray-tracing results demonstrate that ignoring this effect can lead to a severe overestimation of the local standard deviation in a given area. Then, a spatially consistent stochastic street-by-street PL model is established, and a parameterization for 28-GHz UMi cells is given. The model correctly describes the PL as a function of the street orientation as well as the large variance observed for all the PL model parameters.
- 29 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Wireless Communications Letters
- Vol. 6 (21622337) , 1
Censored Multipath Component Cross-Polarization Ratio Modeling
In wireless channel measurements, the relatively weak cross-polarized multipath components (MPCs) are typically severely affected by the measurement noise level. As shown in this letter, the typical cross-polarization ratio (XPR) model parameter estimation, which ignores the existence of censored samples, may lead to significant errors. We demonstrate how to achieve accurate parameter estimates with a maximum likelihood estimator that properly takes into account both the measured XPRs and the censored samples. Also, a new XPR model is presented in which the average XPR is modeled as a function of the MPC excess loss. The new model is shown to be insensitive to the channel measurement noise level. A practical example with measured data in an indoor environment at 60 GHz demonstrates the utility of the approach.
- 29 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Wireless Communications Letters
- Vol. 6 (21622337) , 1
Censored Multipath Component Cross-Polarization Ratio Modeling
In wireless channel measurements, the relatively weak cross-polarized multipath components (MPCs) are typically severely affected by the measurement noise level. As shown in this letter, the typical cross-polarization ratio (XPR) model parameter estimation, which ignores the existence of censored samples, may lead to significant errors. We demonstrate how to achieve accurate parameter estimates with a maximum likelihood estimator that properly takes into account both the measured XPRs and the censored samples. Also, a new XPR model is presented in which the average XPR is modeled as a function of the MPC excess loss. The new model is shown to be insensitive to the channel measurement noise level. A practical example with measured data in an indoor environment at 60 GHz demonstrates the utility of the approach.
- 1 March 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2976-2980
2D Beam-steering with non-symmetrical beam using non-symmetrical integrated lens antenna
This article presents an integrated lens antenna design that allows two-dimensional beam-steering with a non-symmetrical beam. The lens design is based on a traditional integrated lens concept. It is shown that, with a simple modification, the beam-shape can be changed without compromising the beam-steering properties. The limitations and properties of the proposed design are studied. Beam-steering properties of two lens designs are tested with radiation pattern measurements at 77 GHz.
- 1 March 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2976-2980
2D Beam-steering with non-symmetrical beam using non-symmetrical integrated lens antenna
This article presents an integrated lens antenna design that allows two-dimensional beam-steering with a non-symmetrical beam. The lens design is based on a traditional integrated lens concept. It is shown that, with a simple modification, the beam-shape can be changed without compromising the beam-steering properties. The limitations and properties of the proposed design are studied. Beam-steering properties of two lens designs are tested with radiation pattern measurements at 77 GHz.