Chuan He
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chuan He has a total of 71 co-authors. Here are the top co-authors by number of shared publications:
- Wenbo Yang
Key Laboratory of Transportation Tunnel Engineering, Ministry of Education, Southwest Jiaotong University, Chengdu 610031, China
5 shared publications - Chaofan Yao
Key Laboratory of Transportation Tunnel Engineering, Ministry of Education, Southwest Jiaotong University, Chengdu, China
3 shared publications - Gaoyu Ma
MOE Key Laboratory of Transportation Tunnel Engineering, Southwest Jiaotong University, Chengdu 610031, PR China
2 shared publications - Guowen Xu
Key Laboratory of Transportation Tunnel Engineering, Ministry of Education, Southwest Jiaotong University, Chengdu, China
2 shared publications - Qixiang Yan
State Key Laboratory of Intelligent Geotechnics and Tunnelling, Southwest Jiaotong University, Chengdu, China
2 shared publications - Shimin Wang
School of Civil Engineering, Southwest Jiaotong University, Chengdu 611756, China
2 shared publications
Latest Publications
- Open Access
Evolution of Construction Mechanics Behavior in Widening Section of Urban Highway Tunnel with Super Cross-Section
Urban tunnel widening is increasingly used to accommodate growing traffic demand. However, excavation-induced unloading in complex urban geological environments may degrade surrounding-rock properties and compromise structural safety. Previous studies have mainly focused on tunnels with cross-sectional areas below 300 m2, while field-based investigations of tunnels with excavation areas exceeding 400 m2 remain limited. In addition, structural safety assessments often rely on individual indicators. This study investigates the Huofengshan Tunnel in Chongqing, China, an urban tunnel characterized by a densely built-up setting, complex geometry, a low height-to-span ratio, and a maximum excavation area of approximately 440 m2. Field monitoring of deformation and internal forces was conducted at four sections with clear widths of 13.25, 17.45, 20.00, and 25.00 m. Three-dimensional FLAC3D numerical simulations were conducted using a dynamic mechanical-parameter weakening model that accounts for excavation-induced unloading, and the simulation results were validated against field monitoring data. A structural safety assessment framework integrating tunnel deformation, ground-surface settlement, primary-support stress, and secondary-lining stress was established. The analytic hierarchy process–entropy weight method (AHP-EWM) was used to determine indicator weights and establish the tunnel safety redundancy index (TSRI). The results show that tunnel widening induces substantial internal-force redistribution in the support structure, shifting the load-bearing mechanism from arch-waist dominance to joint bearing by the arch shoulder and arch waist. As the clear width increases from 13.25 to 25.00 m, the TSRI increases from 0.231 to 0.385, indicating a reduction in structural safety reserve. This study provides a field-validated analytical framework for characterizing the evolution of mechanical behavior and quantitatively assessing structural safety during tunnel widening, offering a theoretical and methodological reference for the design, construction, and safety assessment of comparable super-large-section urban highway tunnels.
Open AccessEvolution of Construction Mechanics Behavior in Widening Section of Urban Highway Tunnel with Super Cross-Section
Urban tunnel widening is increasingly used to accommodate growing traffic demand. However, excavation-induced unloading in complex urban geological environments may degrade surrounding-rock properties and compromise structural safety. Previous studies have mainly focused on tunnels with cross-sectional areas below 300 m2, while field-based investigations of tunnels with excavation areas exceeding 400 m2 remain limited. In addition, structural safety assessments often rely on individual indicators. This study investigates the Huofengshan Tunnel in Chongqing, China, an urban tunnel characterized by a densely built-up setting, complex geometry, a low height-to-span ratio, and a maximum excavation area of approximately 440 m2. Field monitoring of deformation and internal forces was conducted at four sections with clear widths of 13.25, 17.45, 20.00, and 25.00 m. Three-dimensional FLAC3D numerical simulations were conducted using a dynamic mechanical-parameter weakening model that accounts for excavation-induced unloading, and the simulation results were validated against field monitoring data. A structural safety assessment framework integrating tunnel deformation, ground-surface settlement, primary-support stress, and secondary-lining stress was established. The analytic hierarchy process–entropy weight method (AHP-EWM) was used to determine indicator weights and establish the tunnel safety redundancy index (TSRI). The results show that tunnel widening induces substantial internal-force redistribution in the support structure, shifting the load-bearing mechanism from arch-waist dominance to joint bearing by the arch shoulder and arch waist. As the clear width increases from 13.25 to 25.00 m, the TSRI increases from 0.231 to 0.385, indicating a reduction in structural safety reserve. This study provides a field-validated analytical framework for characterizing the evolution of mechanical behavior and quantitatively assessing structural safety during tunnel widening, offering a theoretical and methodological reference for the design, construction, and safety assessment of comparable super-large-section urban highway tunnels.
- Open Access
Experimental and Numerical Investigation on Mechanical Performance of Shield Tunnel Segments Strengthened by Novel Prefabricated Basalt-Fiber-Reinforced Composite Profiles
To address the challenge of deformation control in operating tunnel structures, this study investigates a novel reinforcement method for operating shield tunnels using a basalt-fiber-reinforced polymer-wrapped concrete-filled steel tube (BFRP-CFST) composite profile. Two primary study variables were considered. At the segment level, the reinforcement condition comprised two levels: unreinforced and BFRP-CFST-reinforced, with three replicate specimens at each level (US-1 to US-3 and RS-1 to RS-3, respectively). At the full-ring level, the number of installed composite profile frames comprised five levels (n = 0, 1, 2, 3, and 4), where n = 0 represented the unreinforced reference condition. A combined experimental and numerical framework was established, including full-scale four-point bending tests on individual tunnel segments and finite element simulations of full-ring linings. Experimental results demonstrate that the ultimate bearing capacity of reinforced segments increased from 534.4 kN to 921.3 kN, corresponding to a 72.4% improvement. The load level before visible cracking increased by 84.2%. At maximum crack widths of 0.2 mm and 2.0 mm, the mid-span displacement of the reinforced segments was reduced by 30.0% and 21.4%, respectively. The test observations indicate that the prefabricated composite profiles effectively delayed crack development and improved the post-cracking stiffness of the segment. Full-ring numerical simulations further showed that installing one to four composite profile frames increased the external load corresponding to a convergence displacement of approximately 10.5 cm by 12.4%, 21.1%, 28.5%, and 37.4%, respectively. Scientifically, the results reveal a staged load-transfer process in which adhesive bonding provides distributed load transfer during the initial response, while mechanical anchors maintain residual load transfer after local interface debonding; they also establish a quantitative relationship between the number of profile frames and full-ring convergence resistance. From an applied engineering perspective, the proposed profile increased the ultimate load and crack-initiation load of the segments by 72.4% and 84.2%, respectively, while its lightweight and prefabricated configuration provides a potentially rapid rehabilitation option for operating shield tunnels.
Open AccessExperimental and Numerical Investigation on Mechanical Performance of Shield Tunnel Segments Strengthened by Novel Prefabricated Basalt-Fiber-Reinforced Composite Profiles
To address the challenge of deformation control in operating tunnel structures, this study investigates a novel reinforcement method for operating shield tunnels using a basalt-fiber-reinforced polymer-wrapped concrete-filled steel tube (BFRP-CFST) composite profile. Two primary study variables were considered. At the segment level, the reinforcement condition comprised two levels: unreinforced and BFRP-CFST-reinforced, with three replicate specimens at each level (US-1 to US-3 and RS-1 to RS-3, respectively). At the full-ring level, the number of installed composite profile frames comprised five levels (n = 0, 1, 2, 3, and 4), where n = 0 represented the unreinforced reference condition. A combined experimental and numerical framework was established, including full-scale four-point bending tests on individual tunnel segments and finite element simulations of full-ring linings. Experimental results demonstrate that the ultimate bearing capacity of reinforced segments increased from 534.4 kN to 921.3 kN, corresponding to a 72.4% improvement. The load level before visible cracking increased by 84.2%. At maximum crack widths of 0.2 mm and 2.0 mm, the mid-span displacement of the reinforced segments was reduced by 30.0% and 21.4%, respectively. The test observations indicate that the prefabricated composite profiles effectively delayed crack development and improved the post-cracking stiffness of the segment. Full-ring numerical simulations further showed that installing one to four composite profile frames increased the external load corresponding to a convergence displacement of approximately 10.5 cm by 12.4%, 21.1%, 28.5%, and 37.4%, respectively. Scientifically, the results reveal a staged load-transfer process in which adhesive bonding provides distributed load transfer during the initial response, while mechanical anchors maintain residual load transfer after local interface debonding; they also establish a quantitative relationship between the number of profile frames and full-ring convergence resistance. From an applied engineering perspective, the proposed profile increased the ultimate load and crack-initiation load of the segments by 72.4% and 84.2%, respectively, while its lightweight and prefabricated configuration provides a potentially rapid rehabilitation option for operating shield tunnels.
- 13 December 2025
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 85 (1) , 44
Soil stresses in sand subjected to reverse faulting: physical modeling and theoretical estimation
- 13 December 2025
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 85 (1) , 44
Soil stresses in sand subjected to reverse faulting: physical modeling and theoretical estimation
- 13 January 2025
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 58 (5) , 5273-5297
The Control Effect of Directional Rock Bolt on Asymmetric Deformation of Layered Soft Rock Tunnel with Different Grades of Large Deformation
- 13 January 2025
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 58 (5) , 5273-5297
The Control Effect of Directional Rock Bolt on Asymmetric Deformation of Layered Soft Rock Tunnel with Different Grades of Large Deformation
- 20 August 2024
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 57 (12) , 10747-10784
Experimental and Numerical Study of Phyllite’s Anisotropic Behavior in 3D Space Under Brazilian Test Conditions
- 20 August 2024
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 57 (12) , 10747-10784
Experimental and Numerical Study of Phyllite’s Anisotropic Behavior in 3D Space Under Brazilian Test Conditions
- 16 March 2024
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 83 (4) , 1-26
Investigation of Phyllite-based Brazilian tests and fracture failure patterns via AE and PFC3D
- 16 March 2024
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 83 (4) , 1-26
Investigation of Phyllite-based Brazilian tests and fracture failure patterns via AE and PFC3D
- 14 April 2023
- Published by Springer Nature in Acta Geotechnica
- Vol. 18 (10) , 5251-5272
Investigations of filter-clog mechanism and prediction model of slurry penetration during slurry pressure transfer
- 14 April 2023
- Published by Springer Nature in Acta Geotechnica
- Vol. 18 (10) , 5251-5272
Investigations of filter-clog mechanism and prediction model of slurry penetration during slurry pressure transfer
- 24 February 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 371, 130789
Performance assessment of partially corrosion-damaged RC segment incorporating the spatial variability of steel corrosion
- 24 February 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 371, 130789
Performance assessment of partially corrosion-damaged RC segment incorporating the spatial variability of steel corrosion
- 6 January 2023
- Published by Springer Nature in Acta Geotechnica
- Vol. 18 (7) , 3435-3449
New insights into normal fault rupture propagation in sand
- 6 January 2023
- Published by Springer Nature in Acta Geotechnica
- Vol. 18 (7) , 3435-3449
New insights into normal fault rupture propagation in sand