Shih-Huang Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shih-Huang Chen has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Putri Adhitana Paramitha
Department of Civil Engineering, National Central University 2 , No. 300, Jung-da Rd., Jung-li City, Taoyuan 32054
4 shared publicationsChia-Chen Wu
Ph.D. Candidate, Dept. of Civil Engineering, National Central Univ., No. 300, Jhongda Rd., Jhongli City, Taoyuan County 32001, Taiwan
3 shared publications- Putri Adhitana Paramitha
National Central University
3 shared publications Ching-Tsung Hung
Chaoyang University of Technology
2 shared publicationsMeng-Hsin Kuo
National Central University
2 shared publicationsTyas Wahyu Pramesthi
Master, Dept. of Civil Engineering, National Central Univ., No. 300, Jhongda Rd., Jhongli City, Taoyuan County 32001, Taiwan
2 shared publications
Latest Publications
- 24 July 2026
- Published by Springer Nature
- p. 45-51
Performance Evaluation of Cold Mix Recycled Asphalt Concrete Base Layer on Taiwan’s Expressway No. 61
- 24 July 2026
- Published by Springer Nature
- p. 45-51
Performance Evaluation of Cold Mix Recycled Asphalt Concrete Base Layer on Taiwan’s Expressway No. 61
- 9 July 2026
- Published by Springer Nature
- p. 724-729
Mechanical Performance and Toughness Evaluation of Warm Mix Asphalt Binders Modified with SBS/SEBS/SIS Polymers
- 9 July 2026
- Published by Springer Nature
- p. 724-729
Mechanical Performance and Toughness Evaluation of Warm Mix Asphalt Binders Modified with SBS/SEBS/SIS Polymers
- Open Access
- 30 July 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Applied Mechanics
- Vol. 121 (1) , 146-162
Laboratory Study of Aging Characteristics of Binder Warm Mix Asphalt Chemical Additive: Rutting, Fatigue Resistance, and Chemical Composition
The research aims to comprehensively assess the impact of anti-stripping agents ZycoTherm (Zyc) and Evotherm M1 (EM1) on Warm Mix Asphalt (WMA). The study employs a range of laboratory tests to investigate the rheological and chemical properties of modified asphalt. Conventional tests such as penetration and softening points are employed alongside advanced techniques including Dynamic Shear Rheometer (DSR), and Linear Amplitude Sweep (LAS) analyses to delve into the rheological properties. Chemical properties (SARA) were analyzed using thin-layer chromatography. Both short-term aging (STA) using The Rolling Thin-Film Oven (RTFO) and long-term aging (LTA) based on the Universal Simple Aging Test are simulated under controlled laboratory conditions. It was found in conventional tests that the value changed, but not significantly. In terms of rutting and fatigue performance, Zyc 0.05% showed positive results. Fatigue behavior shows Zyc has better resistance. The asphalt fractional composition test showed changes in each age condition.
- 30 July 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Applied Mechanics
- Vol. 121 (1) , 146-162
Open AccessLaboratory Study of Aging Characteristics of Binder Warm Mix Asphalt Chemical Additive: Rutting, Fatigue Resistance, and Chemical Composition
The research aims to comprehensively assess the impact of anti-stripping agents ZycoTherm (Zyc) and Evotherm M1 (EM1) on Warm Mix Asphalt (WMA). The study employs a range of laboratory tests to investigate the rheological and chemical properties of modified asphalt. Conventional tests such as penetration and softening points are employed alongside advanced techniques including Dynamic Shear Rheometer (DSR), and Linear Amplitude Sweep (LAS) analyses to delve into the rheological properties. Chemical properties (SARA) were analyzed using thin-layer chromatography. Both short-term aging (STA) using The Rolling Thin-Film Oven (RTFO) and long-term aging (LTA) based on the Universal Simple Aging Test are simulated under controlled laboratory conditions. It was found in conventional tests that the value changed, but not significantly. In terms of rutting and fatigue performance, Zyc 0.05% showed positive results. Fatigue behavior shows Zyc has better resistance. The asphalt fractional composition test showed changes in each age condition.
- 20 June 2020
- Published by Springer Nature
- p. 375-384
Performance Evaluation of Hybrid EAF Slag and RAP in Pavement
- 20 June 2020
- Published by Springer Nature
- p. 375-384
Performance Evaluation of Hybrid EAF Slag and RAP in Pavement
- 1 December 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 144 (4) , 04018053
Utilization of Blue Ray 2D Laser CCD to Prevent Luminance Disturbance during Pavement Texture Measurement
In recent years, laser techniques have replaced the commonly used sand pitch method to measure pavement surface texture. However, the conventional red ray laser charge-coupled devices (CCDs), both the one-dimensional (1D) and two-dimensional (2D) versions, traditionally have been influenced by luminance. The study presented in this paper developed an intelligent texture measurement system (ITMS) with a blue ray 2D laser CCD instead of the red ray CCD used in previous pavement surface texture measurement research, in accordance with ISO 13473-3. In this study’s light tests, a halogen lamp was adopted to simulate the light (Klux). The results indicated that the red ray 2D laser could not read the texture under lighting of more than 5 Klux while the blue ray 2D laser was minimally influenced by the light. In addition, when a 15-cm mask was used, the accuracy of the ITMS improved. Based on the presented results, the blue ray 2D laser CCD was found to be more stable than the red ray 2D laser CCD in texture measurement, and a light-protection mask (more than 15 cm) would further protect the laser from the disturbance of luminance.
- 1 December 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 144 (4) , 04018053
Utilization of Blue Ray 2D Laser CCD to Prevent Luminance Disturbance during Pavement Texture Measurement
In recent years, laser techniques have replaced the commonly used sand pitch method to measure pavement surface texture. However, the conventional red ray laser charge-coupled devices (CCDs), both the one-dimensional (1D) and two-dimensional (2D) versions, traditionally have been influenced by luminance. The study presented in this paper developed an intelligent texture measurement system (ITMS) with a blue ray 2D laser CCD instead of the red ray CCD used in previous pavement surface texture measurement research, in accordance with ISO 13473-3. In this study’s light tests, a halogen lamp was adopted to simulate the light (Klux). The results indicated that the red ray 2D laser could not read the texture under lighting of more than 5 Klux while the blue ray 2D laser was minimally influenced by the light. In addition, when a 15-cm mask was used, the accuracy of the ITMS improved. Based on the presented results, the blue ray 2D laser CCD was found to be more stable than the red ray 2D laser CCD in texture measurement, and a light-protection mask (more than 15 cm) would further protect the laser from the disturbance of luminance.
- 24 October 2018
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 47 (3) , 1864-1875
Evaluation of Innovative Cold Mix Recycled Asphalt Concrete as Backfill Material in Pipeline Maintenance
Cold mix recycled asphalt (CMRA) concrete was evaluated to be an innovative repair material to improve the pavement quality and environmental impact on pipeline maintenance in this study. The study presented and specifically examined the use of CMRA with 2.5 % foam asphalt content as a replacement for the currently used controlled low-strength material (CLSM) as pipeline backfill material. CMRA’s material properties, performance, carbon dioxide emissions, cost, and construction time were analyzed in this study to confirm the advantages and limitations of CMRA. The results concluded that CMRA performed better than CLSM for all the items analyzed. Specifically, according to the performance analysis, CMRA exhibited a better Marshall stability index, California bearing ratio, indirect tensile strength, tensile strength ratio, anti-rutting ability, and penetration than the standards specified. Furthermore, the average carbon emissions of CMRA were 36 % less than CLSM, could save at least 2 h of construction time per cubic meter of construction, and immediately opened traffic. However, CRMA’s construction cost in this study was similar to CLSM and was only lower (up to 2.3 %) by considering a similar price of cement, asphalt, and additives. Based on the aforementioned results, this study concluded that the findings may be of particular interest for Taiwanese pipeline maintenance projects as a backfill material and is worthy of further research.
- 24 October 2018
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 47 (3) , 1864-1875
Evaluation of Innovative Cold Mix Recycled Asphalt Concrete as Backfill Material in Pipeline Maintenance
Cold mix recycled asphalt (CMRA) concrete was evaluated to be an innovative repair material to improve the pavement quality and environmental impact on pipeline maintenance in this study. The study presented and specifically examined the use of CMRA with 2.5 % foam asphalt content as a replacement for the currently used controlled low-strength material (CLSM) as pipeline backfill material. CMRA’s material properties, performance, carbon dioxide emissions, cost, and construction time were analyzed in this study to confirm the advantages and limitations of CMRA. The results concluded that CMRA performed better than CLSM for all the items analyzed. Specifically, according to the performance analysis, CMRA exhibited a better Marshall stability index, California bearing ratio, indirect tensile strength, tensile strength ratio, anti-rutting ability, and penetration than the standards specified. Furthermore, the average carbon emissions of CMRA were 36 % less than CLSM, could save at least 2 h of construction time per cubic meter of construction, and immediately opened traffic. However, CRMA’s construction cost in this study was similar to CLSM and was only lower (up to 2.3 %) by considering a similar price of cement, asphalt, and additives. Based on the aforementioned results, this study concluded that the findings may be of particular interest for Taiwanese pipeline maintenance projects as a backfill material and is worthy of further research.
- 30 January 2018
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 20 (12) , 1392-1399
Explore pavement roughness under various funding for the Taiwan provincial highways using LCCA
Pavement roughness has always been a concern for road users and highway agencies. The Directorate General of Highways (DGH), which administers the Taiwan Provincial Highways, stated that the maintenance lane-kilometres it manages increase daily. In recent years, the Taiwan government has been investing a great deal of money in social and health care services while decreasing annual funding for infrastructure. DGH is no exception to these budget-cutting efforts and now faces the challenge of how to maintain an acceptable level of pavement roughness with limited funding. With this challenge in mind, the main objective of this study was to explore pavement roughness under various maintenance funding levels for the Taiwan Provincial Highway. First, the researchers visited all five Taiwan pavement maintenance offices and several branches to collect roughness data, annual financial reports and expert opinions. Then, life-cycle cost analysis (LCCA), specifically RealCost LCCA software was used to estimate an annual minimum budget for DGH. Taiwan local and typical data were used in this analysis. The results of the LCCA conducted in this study indicated that DGH should be spending a minimum of 5.2 billion NTD per year on pavements to keep them in good condition.
- 30 January 2018
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 20 (12) , 1392-1399
Explore pavement roughness under various funding for the Taiwan provincial highways using LCCA
Pavement roughness has always been a concern for road users and highway agencies. The Directorate General of Highways (DGH), which administers the Taiwan Provincial Highways, stated that the maintenance lane-kilometres it manages increase daily. In recent years, the Taiwan government has been investing a great deal of money in social and health care services while decreasing annual funding for infrastructure. DGH is no exception to these budget-cutting efforts and now faces the challenge of how to maintain an acceptable level of pavement roughness with limited funding. With this challenge in mind, the main objective of this study was to explore pavement roughness under various maintenance funding levels for the Taiwan Provincial Highway. First, the researchers visited all five Taiwan pavement maintenance offices and several branches to collect roughness data, annual financial reports and expert opinions. Then, life-cycle cost analysis (LCCA), specifically RealCost LCCA software was used to estimate an annual minimum budget for DGH. Taiwan local and typical data were used in this analysis. The results of the LCCA conducted in this study indicated that DGH should be spending a minimum of 5.2 billion NTD per year on pavements to keep them in good condition.
- 1 December 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Performance of Constructed Facilities
- Vol. 31 (6)
Erratum for “Environmental Impact Assessment and Total Cost Analysis of BOF and BSSF Slag in Asphalt Concrete” by Shih-Huang Chen, Tyas Wahyu Pramesthi, Putri Adhitana Paramitha, and Chia-Chen Wu
- 1 December 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Performance of Constructed Facilities
- Vol. 31 (6)
Erratum for “Environmental Impact Assessment and Total Cost Analysis of BOF and BSSF Slag in Asphalt Concrete” by Shih-Huang Chen, Tyas Wahyu Pramesthi, Putri Adhitana Paramitha, and Chia-Chen Wu
- 1 August 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Performance of Constructed Facilities
- Vol. 31 (4)
Environmental Impact Assessment and Total Cost Analysis of BOF and BSSF Slag in Asphalt Concrete
Dense grade asphalt concrete (DGAC), a popular surface material in Taiwan, allows for the design of the new recycling materials to reduce the use of natural aggregate. Basic oxygen-furnace (BOF) and Baosteel slag short-flow (BSSF) slag as steel byproduct are rarely used and generally disposed of. This study explores the environmental impact of replacing some of the coarse aggregates with steel slag in DGAC. Four levels of aggregate replacement (10, 20, 30, and 100%) were analyzed. Simulation results indicate that the replacement of coarse aggregate with BOF and BSSF slag increases the global warming potential (GWP) up to 7.13% compared to traditional DGAC during the production phase due to its specific gravity. However, using BOF and BSSF slag saves up to 36.41% of total cost included and reduces the environmental impact by decreasing the use of natural aggregate and the disposal of slag. Based on this result, replacement of a coarse natural aggregate with BOF and BSSF slag in DGAC is feasible and worthy of further research.
- 1 August 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Performance of Constructed Facilities
- Vol. 31 (4)
Environmental Impact Assessment and Total Cost Analysis of BOF and BSSF Slag in Asphalt Concrete
Dense grade asphalt concrete (DGAC), a popular surface material in Taiwan, allows for the design of the new recycling materials to reduce the use of natural aggregate. Basic oxygen-furnace (BOF) and Baosteel slag short-flow (BSSF) slag as steel byproduct are rarely used and generally disposed of. This study explores the environmental impact of replacing some of the coarse aggregates with steel slag in DGAC. Four levels of aggregate replacement (10, 20, 30, and 100%) were analyzed. Simulation results indicate that the replacement of coarse aggregate with BOF and BSSF slag increases the global warming potential (GWP) up to 7.13% compared to traditional DGAC during the production phase due to its specific gravity. However, using BOF and BSSF slag saves up to 36.41% of total cost included and reduces the environmental impact by decreasing the use of natural aggregate and the disposal of slag. Based on this result, replacement of a coarse natural aggregate with BOF and BSSF slag in DGAC is feasible and worthy of further research.