Karan Mehta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Karan Mehta has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
P. Douglas Yoder
School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA 30332 USA
6 shared publicationsYuh-Shiuan Liu
School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA 30332 USA
6 shared publications- Fernando A. Ponce
Department of Physics, Arizona State University, Tempe, AZ, USA
5 shared publications Russell D. Dupuis
School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA 30332 USA
5 shared publicationsTheeradetch Detchprohm
School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA 30332 USA
5 shared publicationsHoon Jeong
School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA 30332 USA
4 shared publications
Latest Publications
- 16 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (4) , 1855-1860
Feedback Tolerant Quantum Dot Lasers Integrated With 300 mm Silicon Photonics
We report on the first quantum dot lasers heterogeneously integrated with 300 mm silicon photonics. The lasers show linewidth enhancement factor near zero, indicating the capability for high feedback tolerance, which enables isolator-free operation. We demonstrate this concept by using a heterogeneous III-V/Si quantum dot laser with a silicon microring modulator in the presence of optical feedback of up to -13dB without degradation to eye quality for a 128 Gb/s PAM-4 signal.
- 16 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (4) , 1855-1860
Feedback Tolerant Quantum Dot Lasers Integrated With 300 mm Silicon Photonics
We report on the first quantum dot lasers heterogeneously integrated with 300 mm silicon photonics. The lasers show linewidth enhancement factor near zero, indicating the capability for high feedback tolerance, which enables isolator-free operation. We demonstrate this concept by using a heterogeneous III-V/Si quantum dot laser with a silicon microring modulator in the presence of optical feedback of up to -13dB without degradation to eye quality for a 128 Gb/s PAM-4 signal.
- 15 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (9) , 3300-3305
Measurement of the Nonlinear Loss and Effective Free Carrier Lifetime in Silicon Microring Resonators
A methodology is presented to characterize the nonlinear absorption loss coefficient and the effective free carrier lifetime in silicon ring resonators at high intra-ring optical power density. The proposed methodology uses a continuous-wave pump-probe measurement to capture distortion-free transmission spectra in the regime of nonlinear absorption. The measured nonlinear loss coefficient using this method is 30–40% higher than that obtained with a single high-power continuous-wave laser. The pump-probe measurement also reveals that the optical loss sharply increases beyond ∼11.6 mW in the bus waveguide for the ring design with the highest quality-factor, most likely due to the saturation of trap states by electrons and holes generated by two-photon absorption.
- 15 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (9) , 3300-3305
Measurement of the Nonlinear Loss and Effective Free Carrier Lifetime in Silicon Microring Resonators
A methodology is presented to characterize the nonlinear absorption loss coefficient and the effective free carrier lifetime in silicon ring resonators at high intra-ring optical power density. The proposed methodology uses a continuous-wave pump-probe measurement to capture distortion-free transmission spectra in the regime of nonlinear absorption. The measured nonlinear loss coefficient using this method is 30–40% higher than that obtained with a single high-power continuous-wave laser. The pump-probe measurement also reveals that the optical loss sharply increases beyond ∼11.6 mW in the bus waveguide for the ring design with the highest quality-factor, most likely due to the saturation of trap states by electrons and holes generated by two-photon absorption.
- 15 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 35 (7) , 365-368
High-Power Heterogeneously Integrated III-V/Silicon Superluminescent Diode
We demonstrate heterogeneously integrated O-band superluminescent diodes (SLDs) emitting 10 mW of continuous-wave output power at a device temperature of up to 65 °C. At 10 mW output power, the SLD has a wall-plug efficiency of 3.1% at 25 °C and 1.3% at 65 °C; a 3-dB optical bandwidth of 20–30 nm; and spectral modulation (ripple amplitude) of 0.13 (1.1 dB) at 25 °C and 0.09 (0.8 dB) at 65 °C. This is the highest reported output power and efficiency for a SLD integrated with silicon by more than one order of magnitude, which opens up new applications for cheaper and more compact SLD-based photonics integrated circuits.
- 15 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 35 (7) , 365-368
High-Power Heterogeneously Integrated III-V/Silicon Superluminescent Diode
We demonstrate heterogeneously integrated O-band superluminescent diodes (SLDs) emitting 10 mW of continuous-wave output power at a device temperature of up to 65 °C. At 10 mW output power, the SLD has a wall-plug efficiency of 3.1% at 25 °C and 1.3% at 65 °C; a 3-dB optical bandwidth of 20–30 nm; and spectral modulation (ripple amplitude) of 0.13 (1.1 dB) at 25 °C and 0.09 (0.8 dB) at 65 °C. This is the highest reported output power and efficiency for a SLD integrated with silicon by more than one order of magnitude, which opens up new applications for cheaper and more compact SLD-based photonics integrated circuits.
- 1 January 2023
- Published by Optica Publishing Group
- p. ATh5A.6
Heterogeneously Integrated Hybrid III-V/Silicon Superluminescent Diode with >10 mW Output Power
We demonstrate an O-band on-chip superluminescent diode emitting 10 mW broadband output power at 65 °C with a ripple amplitude of 0.8 dB. This is the highest reported power and efficiency for an on-chip SLD.
- 1 January 2023
- Published by Optica Publishing Group
- p. ATh5A.6
Heterogeneously Integrated Hybrid III-V/Silicon Superluminescent Diode with >10 mW Output Power
We demonstrate an O-band on-chip superluminescent diode emitting 10 mW broadband output power at 65 °C with a ripple amplitude of 0.8 dB. This is the highest reported power and efficiency for an on-chip SLD.
- Open Access
- 6 August 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (18)
Philosophy of Approaching a Laser Design Problem: Illustrated by the Design of Ultraviolet Vertical‐Cavity Laser Diodes
The objective of this article is to demonstrate a general approach to the problem of designing a novel laser diode. This involves first understanding prior work in this and related fields (literature survey), and then acquiring a thorough understanding of the relevant physics. This in turn enables the development and/or selection of appropriate models and tools for that problem followed by partitioning the problem into smaller solvable chunks. This involves identifying the key contributing factors affecting poor laser performance (sources of optical loss, poor injection efficiency, high thermal resistance, etc.), quantifying and ranking their relative importance, and finally finding solutions to these problems. The final step involves putting all these pieces back together to arrive at the final laser design. This step is challenging due to the strong coupling between electrical, optical, and thermal physics in a laser diode. Any design changes must be considered through all three lenses. Herein, this approach to laser design will be demonstrated in the context of a novel III–N‐based ultraviolet vertical‐cavity surface‐emitting laser diode (UV‐VCSEL).
- 6 August 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (18)
Open AccessPhilosophy of Approaching a Laser Design Problem: Illustrated by the Design of Ultraviolet Vertical‐Cavity Laser Diodes
The objective of this article is to demonstrate a general approach to the problem of designing a novel laser diode. This involves first understanding prior work in this and related fields (literature survey), and then acquiring a thorough understanding of the relevant physics. This in turn enables the development and/or selection of appropriate models and tools for that problem followed by partitioning the problem into smaller solvable chunks. This involves identifying the key contributing factors affecting poor laser performance (sources of optical loss, poor injection efficiency, high thermal resistance, etc.), quantifying and ranking their relative importance, and finally finding solutions to these problems. The final step involves putting all these pieces back together to arrive at the final laser design. This step is challenging due to the strong coupling between electrical, optical, and thermal physics in a laser diode. Any design changes must be considered through all three lenses. Herein, this approach to laser design will be demonstrated in the context of a novel III–N‐based ultraviolet vertical‐cavity surface‐emitting laser diode (UV‐VCSEL).
- 28 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 55 (5) , 1-8
Thermal Design Considerations for III-N Vertical-Cavity Surface-Emitting Lasers Using Electro-Opto-Thermal Numerical Simulations
III-N VCSELs undergo severe self-heating which limits the output optical power. This makes thermal management a critical design consideration. The three most common VCSEL structures (hybrid VCSELs, flip-chip VCSELs and ELOG VCSELs) have been studied using advanced self-consistent electro-opto-thermal numerical simulations. The key geometric and material parameters affecting the thermal resistance of these devices have been identified. Our simulations suggest that some of the proposed solutions and design modifications can increase the maximum optical output power by as much 100%. This manuscript also describes the correct method of using numerical simulation in device design—to predict trends and isolate the key factors affecting device performance.
- 28 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 55 (5) , 1-8
Thermal Design Considerations for III-N Vertical-Cavity Surface-Emitting Lasers Using Electro-Opto-Thermal Numerical Simulations
III-N VCSELs undergo severe self-heating which limits the output optical power. This makes thermal management a critical design consideration. The three most common VCSEL structures (hybrid VCSELs, flip-chip VCSELs and ELOG VCSELs) have been studied using advanced self-consistent electro-opto-thermal numerical simulations. The key geometric and material parameters affecting the thermal resistance of these devices have been identified. Our simulations suggest that some of the proposed solutions and design modifications can increase the maximum optical output power by as much 100%. This manuscript also describes the correct method of using numerical simulation in device design—to predict trends and isolate the key factors affecting device performance.
- 9 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 55 (3) , 1
Corrections to “Lateral Current Spreading in III-N Ultraviolet Vertical-Cavity Surface-Emitting Lasers Using Modulation-Doped Short Period Superlattices” [Aug 18 Art. no. 2400507]
There is an error in Fig. 4 of [1] in the TE 01 optical mode profile. The error is due to the author forgetting to rescale the x-axis when plotting the optical mode profile on the right y-axis. This oversight occurred because the optical mesh is different from the electrical mesh, and the correct figure is shown below. We wish to emphasize that this was merely a plotting error, and hence all of the results and conclusions presented in the manuscript remain unchanged. We sincerely regret the error.
- 9 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 55 (3) , 1
Corrections to “Lateral Current Spreading in III-N Ultraviolet Vertical-Cavity Surface-Emitting Lasers Using Modulation-Doped Short Period Superlattices” [Aug 18 Art. no. 2400507]
There is an error in Fig. 4 of [1] in the TE 01 optical mode profile. The error is due to the author forgetting to rescale the x-axis when plotting the optical mode profile on the right y-axis. This oversight occurred because the optical mesh is different from the electrical mesh, and the correct figure is shown below. We wish to emphasize that this was merely a plotting error, and hence all of the results and conclusions presented in the manuscript remain unchanged. We sincerely regret the error.
- 18 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 54 (6) , 1-11
Theory and Design of Electron Blocking Layers for III-N-Based Laser Diodes by Numerical Simulation
Although both III-N laser diodes and LEDs employ electron blocking layers (EBLs) to reduce electron leakage from the active region, laser diodes typically operate at far higher current densities than LEDs. Shortcomings of the common rectangular EBL are discussed. Two alternative EBL designs have been systematically studied using numerical simulation: the Inverse-Tapered EBL and the Inverse-Tapered Step-Graded EBL. It is shown that the efficacy of each of these EBL designs depends strongly on the operational current density, suggesting that EBL design considerations for III-N laser diodes and LEDs are fundamentally different.
- 18 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 54 (6) , 1-11
Theory and Design of Electron Blocking Layers for III-N-Based Laser Diodes by Numerical Simulation
Although both III-N laser diodes and LEDs employ electron blocking layers (EBLs) to reduce electron leakage from the active region, laser diodes typically operate at far higher current densities than LEDs. Shortcomings of the common rectangular EBL are discussed. Two alternative EBL designs have been systematically studied using numerical simulation: the Inverse-Tapered EBL and the Inverse-Tapered Step-Graded EBL. It is shown that the efficacy of each of these EBL designs depends strongly on the operational current density, suggesting that EBL design considerations for III-N laser diodes and LEDs are fundamentally different.
- 18 June 2018
- Published by AIP Publishing in Applied Physics Letters
- Vol. 112 (25) , 252103
Negative differential resistance in GaN homojunction tunnel diodes and low voltage loss tunnel contacts
The current-voltage characteristics and metastability in GaN p++/n++ homojunction tunnel diodes and n++/p++/i/n tunnel-contacted diodes grown via metal modulated epitaxy have been investigated. The room temperature negative differential resistance (NDR) beginning at ∼1.35 V is reported for GaN homojunction devices grown on sapphire. The NDR vanishes, and the conductivity increases as multiple I-V sweeps are performed, thus suggesting that charge trapping states with long trap lifetimes exist at defect sites, and these traps play a crucial role in the tunneling mechanism. Additionally, the use of extremely high n-type (ND ∼ 4.6 × 1020 cm−3) and p-type (NA ∼ 7.7× 1020 cm−3) doping results in a near linear characteristic with minimal rectification at current densities less than 200 A/cm2 and soft rectification above this current density. Forward-bias tunneling and NDR are still present at 77 K. The highest silicon-doped n++/p++/i/n tunnel-contacted pin diode demonstrates a turn-on voltage of 3.12 V, only 0.14 V higher than that of the pin control diode, and an improved specific on-resistance of 3.24 × 10−4 Ω cm2, which is 13% lower than that of the control pin diode.
- 18 June 2018
- Published by AIP Publishing in Applied Physics Letters
- Vol. 112 (25) , 252103
Negative differential resistance in GaN homojunction tunnel diodes and low voltage loss tunnel contacts
The current-voltage characteristics and metastability in GaN p++/n++ homojunction tunnel diodes and n++/p++/i/n tunnel-contacted diodes grown via metal modulated epitaxy have been investigated. The room temperature negative differential resistance (NDR) beginning at ∼1.35 V is reported for GaN homojunction devices grown on sapphire. The NDR vanishes, and the conductivity increases as multiple I-V sweeps are performed, thus suggesting that charge trapping states with long trap lifetimes exist at defect sites, and these traps play a crucial role in the tunneling mechanism. Additionally, the use of extremely high n-type (ND ∼ 4.6 × 1020 cm−3) and p-type (NA ∼ 7.7× 1020 cm−3) doping results in a near linear characteristic with minimal rectification at current densities less than 200 A/cm2 and soft rectification above this current density. Forward-bias tunneling and NDR are still present at 77 K. The highest silicon-doped n++/p++/i/n tunnel-contacted pin diode demonstrates a turn-on voltage of 3.12 V, only 0.14 V higher than that of the pin control diode, and an improved specific on-resistance of 3.24 × 10−4 Ω cm2, which is 13% lower than that of the control pin diode.
- 15 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 54 (4) , 1-7
Lateral Current Spreading in III-N Ultraviolet Vertical-Cavity Surface-Emitting Lasers Using Modulation-Doped Short Period Superlattices
Lateral hole injection into AlGaN-based ultraviolet (UV) vertical-cavity light-emitting lasers (VCSELs) has been studied via numerical simulation. For blue and violet vertical cavity light emitters, indium tin oxide (ITO) is most commonly used as a transparent current spreading layer to increase the overlap between the optical mode and the radial current profile. However, ITO has very high optical losses in the UV spectrum, so alternative schemes for lateral current spreading have been investigated for use in UV-VCSELs. A modulation doped short-period superlattice (MD-SPSL) has been proposed as a transparent lateral current spreading layer in UV-VCSELs. The narrow bandgap unintentionally doped (uid) material maintains a high mobility due to reduced impurity scattering and has a high free hole concentration due to modulation doping, thus forming highly conductive channels which aid lateral hole transport. This has been shown to partially mitigate current crowding around the current aperture. To account for imperfect modulation doping due to the magnesium memory effects and other factors, the effect of varying the hole mobility in the uid-narrow bandgap layer of the MD-SPSL from 13-300 cm 2 /(V · s) on the threshold current and slope efficiency has also been studied. Employing an MD-SPSL results in a significant reduction in the threshold current and slope efficiency compared to ITO, and the extent of the improvement depends on the hole mobility in the uid-AlGaN layer.
- 15 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 54 (4) , 1-7
Lateral Current Spreading in III-N Ultraviolet Vertical-Cavity Surface-Emitting Lasers Using Modulation-Doped Short Period Superlattices
Lateral hole injection into AlGaN-based ultraviolet (UV) vertical-cavity light-emitting lasers (VCSELs) has been studied via numerical simulation. For blue and violet vertical cavity light emitters, indium tin oxide (ITO) is most commonly used as a transparent current spreading layer to increase the overlap between the optical mode and the radial current profile. However, ITO has very high optical losses in the UV spectrum, so alternative schemes for lateral current spreading have been investigated for use in UV-VCSELs. A modulation doped short-period superlattice (MD-SPSL) has been proposed as a transparent lateral current spreading layer in UV-VCSELs. The narrow bandgap unintentionally doped (uid) material maintains a high mobility due to reduced impurity scattering and has a high free hole concentration due to modulation doping, thus forming highly conductive channels which aid lateral hole transport. This has been shown to partially mitigate current crowding around the current aperture. To account for imperfect modulation doping due to the magnesium memory effects and other factors, the effect of varying the hole mobility in the uid-narrow bandgap layer of the MD-SPSL from 13-300 cm 2 /(V · s) on the threshold current and slope efficiency has also been studied. Employing an MD-SPSL results in a significant reduction in the threshold current and slope efficiency compared to ITO, and the extent of the improvement depends on the hole mobility in the uid-AlGaN layer.