Claudio Casarosa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Claudio Casarosa has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Alessandro Franco
Department of Energy, Systems, Territory, and Constructions Engineering (DESTEC), University of Pisa, Largo Lucio Lazzarino, 56122 Pisa, Italy
6 shared publications L. Martorano
4 shared publicationsA. Carotenuto
3 shared publicationsE. Latrofa
3 shared publicationsAlberto Carotenuto
2 shared publications- Guido Buresti
Università di Pisa
2 shared publications
Latest Publications
- 1 March 2015
- Published by Elsevier in Applied Thermal Engineering
- Vol. 78, 649-657
Thermodynamic analysis of direct expansion configurations for electricity production by LNG cold energy recovery
- 1 March 2015
- Published by Elsevier in Applied Thermal Engineering
- Vol. 78, 649-657
Thermodynamic analysis of direct expansion configurations for electricity production by LNG cold energy recovery
- Open Access
- 19 November 2014
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 547
Thermodynamic and heat transfer analysis of LNG energy recovery for power production
- 19 November 2014
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 547
Open AccessThermodynamic and heat transfer analysis of LNG energy recovery for power production
- Open Access
- 19 November 2014
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 547
Analysis of thermodynamic losses in ground source heat pumps and their influence on overall system performance
- 19 November 2014
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 547
Open AccessAnalysis of thermodynamic losses in ground source heat pumps and their influence on overall system performance
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 77-84
DJOSER: Analytical Thermal Simulator for Multilayer Electronic Structures. Theory and Numerical Implementation
This paper presents a steady-state thermal simulation strategy called DJOSER, which is dedicated primarily but not exclusively to packaging structures for electronic devices. It is applicable to structures that can be likened to a set of homogeneous layers stacked one on top of the other and possibly separated by thermal contact resistances, where the dissipated powers are due to two-dimensional heat sources distributed on the interfaces between the layers. A broad range of contour conditions and types of dissipated powers is included to make the models as close as possible to the typical structures of modern assembly technologies. Flow and temperature distributions are obtained via a system of integral equations that can be translated directly, with the usual squaring techniques, into a linear algebraic system
- 1 January 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 77-84
DJOSER: Analytical Thermal Simulator for Multilayer Electronic Structures. Theory and Numerical Implementation
This paper presents a steady-state thermal simulation strategy called DJOSER, which is dedicated primarily but not exclusively to packaging structures for electronic devices. It is applicable to structures that can be likened to a set of homogeneous layers stacked one on top of the other and possibly separated by thermal contact resistances, where the dissipated powers are due to two-dimensional heat sources distributed on the interfaces between the layers. A broad range of contour conditions and types of dissipated powers is included to make the models as close as possible to the typical structures of modern assembly technologies. Flow and temperature distributions are obtained via a system of integral equations that can be translated directly, with the usual squaring techniques, into a linear algebraic system
- 1 January 2004
- Published by Begell House Inc. Publishers
- p. 413-420
Steady-state thermal mapping of electronic devices and circuits with multi-layer stack assembly by analytical relationships
This paper deals with an analytical model for the steady-state temperature mapping of electronic devices and system boards. It is devoted to solid structures which can be schematically modelled as a stack of several homogeneous layers of different materials and different sizes, also with various degree of asymmetry, and with two-dimensionally distributed heat generations. This mathematical model was implemented to replace conventional finite-elements (FEM) thermal simulators for fast thermal mappings, accurate within 1% and able to run in interaction with electrical and electro-thermal automatic design tools. His convenience in terms of speed and calculation amounts is due to the required 2-D meshing grids only at the interfaces instead of 3-D. The implemented thermal simulation program was validated by comparing the results of some virtual samples with the corresponding temperature and heat flux maps obtained with the FEM analysis. The amount and the origin of the error percentages with respect to the FEM analysis were also investigated as a functions of the free input parameters of the model.
- 1 January 2004
- Published by Begell House Inc. Publishers
- p. 413-420
Steady-state thermal mapping of electronic devices and circuits with multi-layer stack assembly by analytical relationships
This paper deals with an analytical model for the steady-state temperature mapping of electronic devices and system boards. It is devoted to solid structures which can be schematically modelled as a stack of several homogeneous layers of different materials and different sizes, also with various degree of asymmetry, and with two-dimensionally distributed heat generations. This mathematical model was implemented to replace conventional finite-elements (FEM) thermal simulators for fast thermal mappings, accurate within 1% and able to run in interaction with electrical and electro-thermal automatic design tools. His convenience in terms of speed and calculation amounts is due to the required 2-D meshing grids only at the interfaces instead of 3-D. The implemented thermal simulation program was validated by comparing the results of some virtual samples with the corresponding temperature and heat flux maps obtained with the FEM analysis. The amount and the origin of the error percentages with respect to the FEM analysis were also investigated as a functions of the free input parameters of the model.
- 1 September 2002
- Published by Elsevier in Applied Thermal Engineering
- Vol. 22 (13) , 1501-1518
On some perspectives for increasing the efficiency of combined cycle power plants
- 1 September 2002
- Published by Elsevier in Applied Thermal Engineering
- Vol. 22 (13) , 1501-1518
On some perspectives for increasing the efficiency of combined cycle power plants
- 1 February 2001
- Published by Elsevier in Geothermics
- Vol. 30 (1) , 133-157
Optimizing the position of the tube casing slotted section for geothermal wells with a downhole heat exchanger
- 1 February 2001
- Published by Elsevier in Geothermics
- Vol. 30 (1) , 133-157
Optimizing the position of the tube casing slotted section for geothermal wells with a downhole heat exchanger
- 1 January 2001
- Published by Taylor & Francis in Heat Transfer Engineering
- Vol. 22 (1) , 51-71
On the Optimum Thermal Design of Individual Longitudinal Fins with Rectangular Profile
Search and browse 5 million articles across 13,000 publications from over 250 publishers by publication, subject, publisher, author or keyword.
- 1 January 2001
- Published by Taylor & Francis in Heat Transfer Engineering
- Vol. 22 (1) , 51-71
On the Optimum Thermal Design of Individual Longitudinal Fins with Rectangular Profile
Search and browse 5 million articles across 13,000 publications from over 250 publishers by publication, subject, publisher, author or keyword.