Ning Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ning Lin has a total of 124 co-authors. Here are the top co-authors by number of shared publications:
- Yitai Qian
Department of Applied Chemistry, University of Science and Technology of China, Hefei 230026, P. R. China
36 shared publications Yong Qian
YongJiang Laboratory
35 shared publicationsYitai Qian
Department of Applied Chemistry, University of Science and Technology of China, Hefei, People’s Republic of China
27 shared publicationsJie Zhou
Department of Applied Chemistry University of Science and Technology of China Hefei Anhui 230026 P. R. China
24 shared publicationsYang Li
Department of Applied Chemistry, University of Science and Technology of China, Hefei, People’s Republic of China
21 shared publicationsYing Han
Hefei National Laboratory for Physical Sciences at the Microscale Department of Applied Chemistry University of Science and Technology of China Hefei 230026 P. R. China
20 shared publications
Latest Publications
- 30 September 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (40) , 54860-54871
Reductively Passivated Ion-Conductive Interphase Enables High-Capacity Silicon Anodes for High-Energy-Density All-Solid-State Batteries
Silicon-based all-solid-state batteries (ASSBs) promise high energy density for next-generation energy storage systems. However, the poor solid−solid contact between silicon (Si) and the solid-state electrolyte (SSE), coupled with interfacial instability during cycling, leads to lithium trapping and parasitic reactions, resulting in a low initial coulombic efficiency (ICE). Herein, we report a solution-assisted in situ polymerization and prelithiation strategy to construct a highly ion-conductive interphase via reductive passivation for Si anodes. Lithium biphenyl replenishes active lithium while inducing the in situ formation of a highly stable hybrid interphase composed of polybiphenyl, lithium bis(trifluoromethanesulfonimide) (LiTFSI), and reductively passivated lithium fluoride. The electrochemically stable and ion-conductive interphase minimizes interfacial ion-transport resistance while suppressing SSE decomposition. The engineered anode delivers an ICE of 100.6% with a high electrode-level reversible capacity of 3215 mAh g−1 at the electrode level, enabling an ICE of 96.4% in LiCoO2 full cells (6.2 mAh cm−2) with 96.6% capacity retention after 300 cycles at 1 C. The all-solid-state pouch cell demonstrates a high energy density of 313 Wh kg−1 with 92.7% capacity retention after 100 cycles. This work underscores the critical role of stable ion-conductive interphase design at Si anodes and provides a viable strategy toward practical high-energy-density ASSBs.
- 30 September 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (40) , 54860-54871
Reductively Passivated Ion-Conductive Interphase Enables High-Capacity Silicon Anodes for High-Energy-Density All-Solid-State Batteries
Silicon-based all-solid-state batteries (ASSBs) promise high energy density for next-generation energy storage systems. However, the poor solid−solid contact between silicon (Si) and the solid-state electrolyte (SSE), coupled with interfacial instability during cycling, leads to lithium trapping and parasitic reactions, resulting in a low initial coulombic efficiency (ICE). Herein, we report a solution-assisted in situ polymerization and prelithiation strategy to construct a highly ion-conductive interphase via reductive passivation for Si anodes. Lithium biphenyl replenishes active lithium while inducing the in situ formation of a highly stable hybrid interphase composed of polybiphenyl, lithium bis(trifluoromethanesulfonimide) (LiTFSI), and reductively passivated lithium fluoride. The electrochemically stable and ion-conductive interphase minimizes interfacial ion-transport resistance while suppressing SSE decomposition. The engineered anode delivers an ICE of 100.6% with a high electrode-level reversible capacity of 3215 mAh g−1 at the electrode level, enabling an ICE of 96.4% in LiCoO2 full cells (6.2 mAh cm−2) with 96.6% capacity retention after 300 cycles at 1 C. The all-solid-state pouch cell demonstrates a high energy density of 313 Wh kg−1 with 92.7% capacity retention after 100 cycles. This work underscores the critical role of stable ion-conductive interphase design at Si anodes and provides a viable strategy toward practical high-energy-density ASSBs.
- 8 September 2026
- Published by Elsevier in Energy Storage Materials
- Vol. 91
Oriented nanocrystalline interfaces couple Li+ insertion and interfacial solvation chemistry for fast-charging graphite
- 8 September 2026
- Published by Elsevier in Energy Storage Materials
- Vol. 91
Oriented nanocrystalline interfaces couple Li+ insertion and interfacial solvation chemistry for fast-charging graphite
- 20 August 2026
- Published by Wiley in Advanced Materials
- Vol. 38 (58)
Pressure‐Resilient Electron‐Ion Networks via Multifunctional Carbon Conductive Agents for High‐Rate Solid‐State Batteries
Silicon‐based all‐solid‐state batteries (ASSBs) promise high safety and energy density, yet their rate capability remains fundamentally constrained by the disruption of continuous electron‐ion transport networks induced by large volume variations. Herein, we introduce a pressure‐resilient electron‐ion network enabled by a molten‐salt‐mediated multifunctional carbon conductive agent featuring a graphene‐like stacked framework with uniformly distributed nanopores. This architecture enables synergistic electron‐ion transport (with electronic and ionic conductivities of 133.26 S cm −1 and 1.89 mS cm −1 ), accommodates large deformation (up to 91.3% strain) without structural failure and retains high elasticity under a compressive strain of 80.6%. Operando expansion and kinetic analysis reveal that the elastic network dynamically adapts to silicon volume changes, preserving interfacial integrity and continuous transport pathways. As a result, the composite silicon anode delivers high capacity of 1672.2 mA h g −1 at 3C with 76.5% retention over 300 cycles, and notably sustains 1030.0 mA h g −1 at 3C even under 20 MPa. In full cells, it achieves 76.8 mA h g −1 at 3C under 20 MPa, 2.7 times higher than those based on pristine silicon anodes. Beyond silicon, this strategy can extend to other alloy‐type anodes (e.g., Sn), offering a general paradigm for constructing pressure‐resilient electron‐ion networks toward high‐rate ASSBs.
- 20 August 2026
- Published by Wiley in Advanced Materials
- Vol. 38 (58)
Pressure‐Resilient Electron‐Ion Networks via Multifunctional Carbon Conductive Agents for High‐Rate Solid‐State Batteries
Silicon‐based all‐solid‐state batteries (ASSBs) promise high safety and energy density, yet their rate capability remains fundamentally constrained by the disruption of continuous electron‐ion transport networks induced by large volume variations. Herein, we introduce a pressure‐resilient electron‐ion network enabled by a molten‐salt‐mediated multifunctional carbon conductive agent featuring a graphene‐like stacked framework with uniformly distributed nanopores. This architecture enables synergistic electron‐ion transport (with electronic and ionic conductivities of 133.26 S cm −1 and 1.89 mS cm −1 ), accommodates large deformation (up to 91.3% strain) without structural failure and retains high elasticity under a compressive strain of 80.6%. Operando expansion and kinetic analysis reveal that the elastic network dynamically adapts to silicon volume changes, preserving interfacial integrity and continuous transport pathways. As a result, the composite silicon anode delivers high capacity of 1672.2 mA h g −1 at 3C with 76.5% retention over 300 cycles, and notably sustains 1030.0 mA h g −1 at 3C even under 20 MPa. In full cells, it achieves 76.8 mA h g −1 at 3C under 20 MPa, 2.7 times higher than those based on pristine silicon anodes. Beyond silicon, this strategy can extend to other alloy‐type anodes (e.g., Sn), offering a general paradigm for constructing pressure‐resilient electron‐ion networks toward high‐rate ASSBs.
- Open Access
- 27 July 2026
- Published by Wiley in Advanced Energy Materials
- Vol. 16 (34) , e71369
Liquid‐Phase Spatial Confinement Engineering of sp 2 ‐Rich Closed‐Pore Hard Carbon for Sodium‐Ion Batteries
Porous‐carbon‐based hard carbons have attracted widespread attention as anodes for sodium‐ion batteries owing to the high plateau capacity; however, their practical application is constrained by an intrinsic trade‐off: constructing abundant closed pores enhances capacity but impedes charge transport and compromises structural stability. Herein, we introduce a solvent‐mediated liquid‐phase spatial confinement strategy that fundamentally addresses this dilemma. By incorporating an immiscible nonpolar solvent into a hydrothermal system, carbon precursor deposition and nucleation are precisely regulated within a confined, high‐tension liquid‐phase interface, yielding sp 2 ‐rich closed‐pore hard carbon with simultaneously enhanced capacity, kinetics, and durability. Combined in situ characterizations and theoretical calculations reveal that such sp 2 ‐rich carbon layer significantly promotes electronic and Na + transport, induces preferential anion decomposition to generate a thin and NaF‐rich solid electrolyte interphase, while reinforcing structural integrity. Consequently, the engineered hard carbon delivers high capacity (413.5 mA h g −1 at 20 mA g −1 ) together with excellent rate capability and cycling stability (224.1 mA h g −1 at 2 A g −1 after 4000 cycles). When assembled into Ah‐level 32700 cylindrical cells, it achieves high energy density of 124.0 Wh kg −1 and stable operation over 1200 cycles at 1C, demonstrating a new paradigm for the rational design of high‐performance porous‐carbon‐based hard carbon anodes.
- 27 July 2026
- Published by Wiley in Advanced Energy Materials
- Vol. 16 (34) , e71369
Open AccessLiquid‐Phase Spatial Confinement Engineering of sp 2 ‐Rich Closed‐Pore Hard Carbon for Sodium‐Ion Batteries
Porous‐carbon‐based hard carbons have attracted widespread attention as anodes for sodium‐ion batteries owing to the high plateau capacity; however, their practical application is constrained by an intrinsic trade‐off: constructing abundant closed pores enhances capacity but impedes charge transport and compromises structural stability. Herein, we introduce a solvent‐mediated liquid‐phase spatial confinement strategy that fundamentally addresses this dilemma. By incorporating an immiscible nonpolar solvent into a hydrothermal system, carbon precursor deposition and nucleation are precisely regulated within a confined, high‐tension liquid‐phase interface, yielding sp 2 ‐rich closed‐pore hard carbon with simultaneously enhanced capacity, kinetics, and durability. Combined in situ characterizations and theoretical calculations reveal that such sp 2 ‐rich carbon layer significantly promotes electronic and Na + transport, induces preferential anion decomposition to generate a thin and NaF‐rich solid electrolyte interphase, while reinforcing structural integrity. Consequently, the engineered hard carbon delivers high capacity (413.5 mA h g −1 at 20 mA g −1 ) together with excellent rate capability and cycling stability (224.1 mA h g −1 at 2 A g −1 after 4000 cycles). When assembled into Ah‐level 32700 cylindrical cells, it achieves high energy density of 124.0 Wh kg −1 and stable operation over 1200 cycles at 1C, demonstrating a new paradigm for the rational design of high‐performance porous‐carbon‐based hard carbon anodes.
- 26 May 2026
- Published by Elsevier in Electrochimica Acta
- Vol. 572
Reprogramming plateau-slope sodium storage via coupled sp2/sp3 configuration and interfacial regulation for hard carbon
- 26 May 2026
- Published by Elsevier in Electrochimica Acta
- Vol. 572
Reprogramming plateau-slope sodium storage via coupled sp2/sp3 configuration and interfacial regulation for hard carbon
- 10 May 2026
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 11 (6) , 4629-4640
Lithium-Mediated Reconstruction Activates Carbon Additives into Ion-Electron Percolative Media for All-Solid-State Batteries
- 10 May 2026
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 11 (6) , 4629-4640
Lithium-Mediated Reconstruction Activates Carbon Additives into Ion-Electron Percolative Media for All-Solid-State Batteries
- 24 April 2026
- Published by Elsevier in Energy Storage Materials
- Vol. 88
Deciphering hardness to maximize performance in practical hard carbon anodes for sodium-ion batteries
- 24 April 2026
- Published by Elsevier in Energy Storage Materials
- Vol. 88
Deciphering hardness to maximize performance in practical hard carbon anodes for sodium-ion batteries
- 5 January 2026
- Published by Elsevier in Electrochimica Acta
- Vol. 550
Conformal Al2O3 engineering enables stable and fast-charging microporous carbon-supported Si anodes
- 5 January 2026
- Published by Elsevier in Electrochimica Acta
- Vol. 550
Conformal Al2O3 engineering enables stable and fast-charging microporous carbon-supported Si anodes
- 30 December 2025
- Published by Wiley in Advanced Energy Materials
- Vol. 16 (9)
Molecular‐Level Design of Asphalt‐Derived Hard Carbon with Enhanced Ion/Electron Transport for High‐Rate Sodium‐Ion Batteries
Asphalt is an attractive precursor for hard carbon anodes in sodium‐ion batteries owing to its low cost and excellent structural consistency. However, conventional oxidative strategies, commonly employed for converting asphalt into hard carbon, inevitably distorts the carbon framework, disrupting electronic continuity and Na⁺ diffusion, thereby limiting rate capability. Herein, an integrated molecular‐level strategy is developed by coupling controlled oxidative crosslinking with simultaneous nitrogen modulation, enabling rapid electron/ion transport and delivering outstanding electrochemical performance, as validated in Ah‐level cylindrical cells. Combined with in situ characterizations and theoretical calculations, we uncover that synergistic graphitic and pyrrolic nitrogen species markedly enhance structural stability and charge transport—with the electronic conductivity reaching 41.9 S cm −1 (1.5 × higher) and ionic conductivity up to 0.87 mS cm −1 (1.4 × higher)—while inducing the formation of a thin, NaF‐rich solid electrolyte interface that collectively promotes ultrafast Na + migration and long‐term stability. As a result, the modulated hard carbon achieves a high capacity of 361.8 mA h g −1 , excellent rate capability (190.3 mA h g −1 at 5.0 A g −1 ), and superior cycling stability. When assembled into 18650 cylindrical cells, it delivers energy density of 106.7 Wh kg −1 , retaining 83.8% capacity after 1000 cycles at 1C/10C, highlighting its strong practical potential.
- 30 December 2025
- Published by Wiley in Advanced Energy Materials
- Vol. 16 (9)
Molecular‐Level Design of Asphalt‐Derived Hard Carbon with Enhanced Ion/Electron Transport for High‐Rate Sodium‐Ion Batteries
Asphalt is an attractive precursor for hard carbon anodes in sodium‐ion batteries owing to its low cost and excellent structural consistency. However, conventional oxidative strategies, commonly employed for converting asphalt into hard carbon, inevitably distorts the carbon framework, disrupting electronic continuity and Na⁺ diffusion, thereby limiting rate capability. Herein, an integrated molecular‐level strategy is developed by coupling controlled oxidative crosslinking with simultaneous nitrogen modulation, enabling rapid electron/ion transport and delivering outstanding electrochemical performance, as validated in Ah‐level cylindrical cells. Combined with in situ characterizations and theoretical calculations, we uncover that synergistic graphitic and pyrrolic nitrogen species markedly enhance structural stability and charge transport—with the electronic conductivity reaching 41.9 S cm −1 (1.5 × higher) and ionic conductivity up to 0.87 mS cm −1 (1.4 × higher)—while inducing the formation of a thin, NaF‐rich solid electrolyte interface that collectively promotes ultrafast Na + migration and long‐term stability. As a result, the modulated hard carbon achieves a high capacity of 361.8 mA h g −1 , excellent rate capability (190.3 mA h g −1 at 5.0 A g −1 ), and superior cycling stability. When assembled into 18650 cylindrical cells, it delivers energy density of 106.7 Wh kg −1 , retaining 83.8% capacity after 1000 cycles at 1C/10C, highlighting its strong practical potential.
- 6 August 2025
- Published by Wiley in Advanced Energy Materials
- Vol. 15 (40)
Silicon‐Germanium Solid Solutions with Balanced Ionic/Electronic Conductivity for High‐Rate All‐Solid‐State Batteries
Silicon (Si) is a promising anode for all‐solid‐state batteries (ASSBs) due to its high capacity, but it suffers from low initial Coulombic efficiency (ICE) and poor rate performance. Here, a series of Si–Ge solid solution anodes is synthesized via high‐energy ball milling. Incorporating isomorphous Ge, which has a lower band gap and larger atomic radius, enhances electronic conductivity and induces lattice distortion to broaden Li + diffusion pathways. The optimized Si 7 Ge anode achieves balanced electron/ion conductivities (3.4 × 10 −5 /2.34 × 10 −5 S cm −1 ), which are markedly superior to those of pure Si (8.1 × 10 −8 /3.13 × 10 −6 S cm −1 ). This dual enhancement enables efficient lithiation/delithiation and stable interfacial contact. As a result, the Si 7 Ge anode delivers a high ICE of 89.4%, a reversible capacity of 2631 mAh g −1 , and favorable rate performance (2024 mAh g −1 at 3 C). In full cells with a LiCoO 2 cathode, an ICE of 88.0% and 100 mAh g −1 at 2 C are achieved. An all‐solid‐state pouch cell with the Si 7 Ge anode demonstrates stable cycling over 100 cycles at 0.33 C, highlighting its potential for practical ASSBs applications. This work offers a promising route to overcome Si anode limitations through rational alloy engineering.
- 6 August 2025
- Published by Wiley in Advanced Energy Materials
- Vol. 15 (40)
Silicon‐Germanium Solid Solutions with Balanced Ionic/Electronic Conductivity for High‐Rate All‐Solid‐State Batteries
Silicon (Si) is a promising anode for all‐solid‐state batteries (ASSBs) due to its high capacity, but it suffers from low initial Coulombic efficiency (ICE) and poor rate performance. Here, a series of Si–Ge solid solution anodes is synthesized via high‐energy ball milling. Incorporating isomorphous Ge, which has a lower band gap and larger atomic radius, enhances electronic conductivity and induces lattice distortion to broaden Li + diffusion pathways. The optimized Si 7 Ge anode achieves balanced electron/ion conductivities (3.4 × 10 −5 /2.34 × 10 −5 S cm −1 ), which are markedly superior to those of pure Si (8.1 × 10 −8 /3.13 × 10 −6 S cm −1 ). This dual enhancement enables efficient lithiation/delithiation and stable interfacial contact. As a result, the Si 7 Ge anode delivers a high ICE of 89.4%, a reversible capacity of 2631 mAh g −1 , and favorable rate performance (2024 mAh g −1 at 3 C). In full cells with a LiCoO 2 cathode, an ICE of 88.0% and 100 mAh g −1 at 2 C are achieved. An all‐solid‐state pouch cell with the Si 7 Ge anode demonstrates stable cycling over 100 cycles at 0.33 C, highlighting its potential for practical ASSBs applications. This work offers a promising route to overcome Si anode limitations through rational alloy engineering.