BNBrittany B. Nelson-Cheeseman

Brittany B. Nelson-Cheeseman

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Brittany B. Nelson-Cheeseman has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effects of infill orientation and percentage on the magnetoactive properties of 3D printed magnetic elastomer structures

    by James M. Ennis, Hannah G. Thatcher, Thomas M. Calascione, Jimmy Lu, Nathan A. Fischer, Sarah J. Ziemann, Thomas Höft, Brittany B. Nelson-Cheeseman


  • Open Access

    Hard magnetic elastomers incorporating magnetic annealing and soft magnetic particulate for fused deposition modeling

    by Sarah J. Ziemann, Nathan A. Fischer, Jimmy Lu, Thomas J. Lee, Michael Ennis, Thomas A. Höft, Brittany Nelson-Cheeseman

    Magnetic elastomers with hard or permanent magnetic particulate are able to achieve complex motion not possible from soft magnetic elastomers. Magnetic annealing and fused deposition modeling (FDM) have been used to increase the performance of magnetic composites. This research explores how the magnetoactive properties of hard magnetic elastomers are influenced by magnetic annealing and the addition of the soft magnetic particulate. Three compositions of the thermoplastic magnetic elastomer composite are explored: 15 vol. % SrFe12O19, 10 vol. % SrFe12O19/5 vol. % carbonyl iron, and 5 vol. % SrFe12O19/10 vol. % carbonyl iron. The material is then extruded into FDM filaments. During the extrusion process, some filament is magnetically annealed in an axial applied field. Magnetic hysteresis loops show that the saturation magnetization and coercivity change based on the relative amount of hard and soft magnetic particulate. The presence of only one coercive field indicates magnetic coupling between the hard and soft components. Magnetoactive testing measures each sample’s mechanical deflection angle as a function of transverse applied magnetic field strength. Qualitative and quantitative results reveal that magnetic annealing is critical to the magnetoactive performance of the hard magnetic elastomers. The results also demonstrate that magnetic annealing and increased carbonyl iron both improve the magnetoactive deflection angle for a given applied field. Scanning electron microscopy shows a stratification effect in a range of the filaments. Understanding these hard magnetic elastomers provides insight into how performance can be controlled and optimized by magnetic annealing and combining hard and soft magnetic particulate.


  • Magnetic annealing of extruded thermoplastic magnetic elastomers for 3D-Printing via FDM

    by Nathan A. Fischer, Alex L. Robinson, Thomas J. Lee, Thomas M. Calascione, Lucas Koerner, Brittany B. Nelson-Cheeseman


  • Open Access

    Controlling magnetic properties of 3D-printed magnetic elastomer structures via fused deposition modeling

    by Thomas M. Calascione, Nathan A. Fischer, Thomas J. Lee, Hannah G. Thatcher, Brittany B. Nelson-Cheeseman

    Several methods have been used to optimize performance of magnetic elastomers by controlling the microstructure, such as magnetic annealing. Another way to introduce anisotropy is Fused Deposition Modeling (FDM), which has been shown to manipulate the magnetic anisotropy of rigid printed parts. However, the use of flexible composite materials has not yet been explored due to additional processing challenges. The primary goal of this study is to demonstrate tunable anisotropy of these materials via 3D printed structures without post-processing as a viable means to tune the performance of magnetic elastomer materials. Here, FDM structures were printed with thermoplastic polyurethane (TPU) polymer and either iron, carbonyl iron, or magnetite particulate. In order to determine the relative effect of different parameters on the magnetic properties, a series of samples were printed combining each material type with different aspect ratios, infill percentages, and infill orientations. A Vibrating Sample Magnetometer (VSM) was used to obtain magnetic hysteresis loops in order to compare the magnetic susceptibility between samples. Results demonstrated that FDM provides a method of achieving the directional signature of magnetic annealing without requiring any post-processing; instead, this manifests through the anisotropy of the part’s internal structure. As such, this concept is referred to as infill magnetic annealing (IMA). These variables were found to form a continuum of tunable magnetic responses. Additionally, the chosen particulate transfers its magnetic signature to the composite material. Overall, the highly customizable and nuanced characteristics of 3D-printed magnetic elastomer structures will allow for its application in a broad range of emerging magneto-mechanical applications such as magnetic actuation and soft robotics.


  • Manipulating magnetic anisotropy in fused filament fabricated parts via macroscopic shape, mesoscopic infill orientation, and infill percentage

    by Michael V. Patton, Patrick Ryan, Thomas Calascione, Nathan Fischer, Andrew Morgenstern, Nathan Stenger, Brittany B. Nelson-Cheeseman


  • Open Access

    Thermoplastic magnetic elastomer for fused filament fabrication

    by Andrew H. Morgenstern, Thomas M. Calascione, Nathan A. Fischer, Thomas J. Lee, John E. Wentz, Brittany B. Nelson-Cheeseman

    Magnetorheological elastomers (MREs) are unique smart materials of high elasticity and magnetic susceptibility. MREs are prominent for the high degree of mechanical deformation or changes in stiffness that can be induced by applying magnetic fields. While most MREs are made with thermoset elastomers, this research focuses on the development and testing of a thermoplastic magnetic elastomer for potential use as fused filament fabrication (FFF) filament. FFF, also known as 3D printing, is an additive manufacturing technique that consists of 1D viscous thermoplastic extrusions that create 2D layers that build up to a 3D part. This method of creating parts produces underlying anisotropies which can be tuned to control the properties of the final part. Our thermoplastic magnetic elastomer was created utilizing solvent casting techniques to disperse isotropic magnetic particulate within a thermoplastic polyurethane matrix. Samples were created spanning two different magnetic particulate types (3O4)) and each with three different particulate loadings (20, 30, 40 wt%). The material was then extruded into FFF filaments with a Filastruder. Mechanical stress vs. strain curves of the extruded filaments were obtained using an MTS tensile tester. Magnetic hysteresis loops were acquired with a vibrating sample magnetometer (VSM). The analogous pure polyurethane filaments were also extruded and tested as a control. Our testing indeed shows that altering the magnetic particulate type and weight percentage impacts both the magnetic and mechanical properties of the overall material. In general, the filament samples with iron particulate had higher diametric consistency and were more compliant than those with magnetite particulate. Additionally, samples with magnetite had higher magnetic susceptibility and coercivity but lower saturation magnetization than those with iron. Lastly, increasing particulate percentage increases both the mechanical stiffness and saturation magnetization of the samples, as expected.


  • Open Access

    Dispersion of particulate in solvent cast magnetic thermoplastic polyurethane elastomer composites

    by Thomas J. Lee, Andrew H. Morgenstern, Thomas A. Höft, Brittany B. Nelson-Cheeseman

    Our research focuses on the processing of a thermoplastic magnetorheological elastomer (MRE) by solvent-casting a thermoplastic polyurethane (PU) elastomer with magnetic particulate for fused filament fabrication (FFF) applications. MREs are typically prepared by curing a thermoset silicone with magnetic particulate. Alternatively, thermoplastic MREs may be produced by the addition of magnetic particulate to a thermoplastic elastomer (TPE). FFF is a valuable manufacturing technique that allows for the creation of parts with inherent anisotropies. For the case of an MRE, FFF allows for the production of structures with tunable magnetic susceptibility along different axes. In these composites, the degree of particulate dispersion significantly affects the isotropy of material properties, which becomes increasingly important when small material volumes are used, such as in FFF. Incorporating solvent-casting as a method of producing polymer composites allows for greater control over the particulate addition method, leading to improved dispersion when compared to a polymer melt. For our purposes, composite films were produced in order to examine the effect of wet vs. dry addition of particulate on dispersion. The solvent used for casting was dimethylformamide (DMF). Preparation of polymer solutions included dissolution of PU in DMF to 20 w/v% followed by addition of the magnetic particulate. The particulates used were <150 µm iron powder and 2–4 µm magnetite powder. Composite solutions were made to concentrations of 20, 30, and 40 w/w% particulate to polymer by addition of either dry particulate or particulate pre-suspended in DMF. It was found that wet addition of particulate led to improvement in particulate agglomeration and magnetite particulate exhibited a significantly higher degree of agglomeration than iron.


  • Stabilization of Sr-rich ultrathin epitaxial films of La2-xSrxCuO4

    by Alyssa M. Johnson, Franklin J. Burquest, Hannah M. Larsen, Nicholas Prill, Brittany B. Nelson-Cheeseman


  • Effects of 3-D Printed Structural Characteristics on Magnetic Properties

    by Lindsey M. Bollig, Michael V. Patton, Greg S. Mowry, Brittany B. Nelson-Cheeseman

    Additive manufacturing, particularly 3D printing, allows for completely customizable designs with relatively no limits on geometric complexities. In order to ensure optimal part design for potential magnetic applications, it is crucial to study how the different 3D printer settings impact the magnetic properties of the printed part. Specifically, in this work, it was determined how three structural print parameters (outer shell thickness, internal fill factor, and internal layer orientation) affect the resulting magnetic properties of 3D printed cubic samples. The samples are made using fused deposition modeling of an iron-polymer composite filament. Hysteresis loops were gathered for fields applied along the [100], [110], and [001] directions of the printed cubes. From this, it was determined which combination of print settings should be used to achieve the most desirable magnetic response in terms of magnetic susceptibility, net magnetic moment, and mass-normalized saturation magnetization.


  • Open Access

    Structurally induced magnetization in a La2/3Sr4/3MnO4 superlattice

    by Amish B. Shah, Brittany B. Nelson‐Cheeseman, Ganesh Subramanian, Anand Bhattacharya, John C. H. Spence

    A structural transition has been observed in a digital superlattice of La2/3Sr4/3MnO4, which is correlated to a magnetization enhancement upon cooling the sample. These artificial superlattices were grown layer‐by‐layer using ozone‐assisted molecular beam epitaxy (MBE). Electron diffraction experiments show a phase transition below 150 K in nanopatches of the superlattice, which coincides with an enhanced magnetization starting below 110 K. Atomic scale electron energy loss spectroscopy (EELS) also shows changes in the Mn L2,3 and O K edges, which are related to valence, strain, and the atomic coordination within nanopatches. magnified image Atomic resolution image and EELS showing variations of oxygen and lanthanum signature edges in a La2/3Sr4/3MnO4 supperlattice.