Amir Rezaei Farkoosh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Amir Rezaei Farkoosh has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
David N. Seidman
Northwestern University
10 shared publicationsDavid C. Dunand
8 shared publications- David N. Seidman
Northwestern University
8 shared publications M. Pekguleryuz
5 shared publications- Dieter Isheim
Northwestern University
4 shared publications - Noam Eliaz
Department of Materials Science and Engineering, Tel Aviv University, Tel Aviv 6997801, Israel
3 shared publications
Latest Publications
- Open Access
- 22 July 2026
- Published by Elsevier in SSRN Electronic Journal
Carbide Nanoprecipitates in a Multipurpose High Ni Martensitic Steel,and Their Roles in Quench-lamellarization-tempering
We investigate carbide precipitation and evolution (400 – 850 oC) in a high-Ni, low-C martensitic steel alloyed with Mo, Cr and V, and their influences on austenite reversion and retention during Quench-Lamellarization-Tempering (QLT) treatments. An additional aging (A) step at 400 to 500 °C between quenching and lamellarization generates different carbide nanoprecipitate distributions, which permits studying their influences on lamellarization at 650 °C. Atom-probe tomography reveals that during aging, nanoprecipitates (M2C-type carbides, ~ 0.5 – 1.0 nm) form heterogeneously within martensite primarily at the intra-lath dislocations and inter-lath boundaries. Subsequently the L and T steps lead to M2C nanoprecipitates forming either directly from the solid-solution (QLT) or further growth from prior aging (QALT). Electron backscatter diffraction (EBSD) analyses indicate that after the L-step, the morphology of the Ni-enhanced lamellae and their association with the prior lath and austenite grain boundaries remain unchanged with or without the additional A-step. The QLT and QALT treatments yield similar microstructures, retained austenite volume fractions (~18% via X-ray diffraction), and tensile properties. Nanoprecipitates don’t directly impact austenite reversion, while their formation during the L and T steps redistributes C, depleting it from martensite and austenite, enhancing ductility and toughness while maintaining strength. This on-demand C control mechanism retains C in solid-solution during quenching and depletes it during lamellarization and tempering. This ensures a fine austenite dispersion in a tough martensitic matrix, boosting the transformation-induced plasticity effect. Our findings on C-mediated phase-transformations provide strategies for optimizing high-Ni steels for applications requiring a balance of strength and toughness.
- 22 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCarbide Nanoprecipitates in a Multipurpose High Ni Martensitic Steel,and Their Roles in Quench-lamellarization-tempering
We investigate carbide precipitation and evolution (400 – 850 oC) in a high-Ni, low-C martensitic steel alloyed with Mo, Cr and V, and their influences on austenite reversion and retention during Quench-Lamellarization-Tempering (QLT) treatments. An additional aging (A) step at 400 to 500 °C between quenching and lamellarization generates different carbide nanoprecipitate distributions, which permits studying their influences on lamellarization at 650 °C. Atom-probe tomography reveals that during aging, nanoprecipitates (M2C-type carbides, ~ 0.5 – 1.0 nm) form heterogeneously within martensite primarily at the intra-lath dislocations and inter-lath boundaries. Subsequently the L and T steps lead to M2C nanoprecipitates forming either directly from the solid-solution (QLT) or further growth from prior aging (QALT). Electron backscatter diffraction (EBSD) analyses indicate that after the L-step, the morphology of the Ni-enhanced lamellae and their association with the prior lath and austenite grain boundaries remain unchanged with or without the additional A-step. The QLT and QALT treatments yield similar microstructures, retained austenite volume fractions (~18% via X-ray diffraction), and tensile properties. Nanoprecipitates don’t directly impact austenite reversion, while their formation during the L and T steps redistributes C, depleting it from martensite and austenite, enhancing ductility and toughness while maintaining strength. This on-demand C control mechanism retains C in solid-solution during quenching and depletes it during lamellarization and tempering. This ensures a fine austenite dispersion in a tough martensitic matrix, boosting the transformation-induced plasticity effect. Our findings on C-mediated phase-transformations provide strategies for optimizing high-Ni steels for applications requiring a balance of strength and toughness.
- Open Access
- 4 July 2026
- Published by Elsevier in SSRN Electronic Journal
Microstructural Evolution, Corrosion, Hydrogen Embrittlement, and Diffusivity in a Novel DED-Processed Martensitic Stainless Steel: The Impact of Aging and M23C6 Precipitation
The present study analyzes the microstructural evolution, mechanical properties, and hydrogen resistance of QT17−4+, a novel stainless steel redesigned from conventional 17-4 PH for additive manufacturing to extend its performance. A carefully adjusted Creq/Nieq ratio (~1.41) produces a predominantly martensitic microstructure with ~20 vol.% retained austenite (RA) after directed energy deposition (DED). A heterogeneous distribution of Ti-rich oxy-carbo-nitrides (an Al-Ti-O-rich core with a TiN/TiC shell) and (Cr, Mo, W)-rich carbides is observed within the as-deposited microstructure. Aging at 700–850 °C promotes partial martensite-to-austenite reversion followed by retransformation during cooling, which reduces RA fraction (~11 vol.%), and induces the precipitation of M23C6 carbides. This process yields an improved strength-ductility balance, driven by a 50% reduction in RA and mild precipitation strengthening (~60 MPa) from dispersed carbides (~1.3 vol.%). Under hydrogen charging, the aged samples show a progressive fracture transition from microvoid coalescence to quasi-cleavage-dominated mixed fracture, with hydrogen embrittlement susceptibility of 0.81 (for 36 hours) and 0.43 (for 90 hours). Permeation analyses reveal that aging marginally increases the Dapp from 5.87×10–9 to 7.57×10–9 cm2/s, a result of reduced RA fraction. The low number density (~4×1019 1/m3) of M23C6 carbides minimally affects steady-state diffusivity, but they influence late-stage hydrogen desorption kinetics. The alloy exhibits a uniform passive film, offering excellent stability and resistance to pitting under anodic polarization. These findings demonstrate the significant potential of QT17−4+ as an advanced stainless steel, which combines high strength, good ductility, robust corrosion and hydrogen resistances.
- 4 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMicrostructural Evolution, Corrosion, Hydrogen Embrittlement, and Diffusivity in a Novel DED-Processed Martensitic Stainless Steel: The Impact of Aging and M23C6 Precipitation
The present study analyzes the microstructural evolution, mechanical properties, and hydrogen resistance of QT17−4+, a novel stainless steel redesigned from conventional 17-4 PH for additive manufacturing to extend its performance. A carefully adjusted Creq/Nieq ratio (~1.41) produces a predominantly martensitic microstructure with ~20 vol.% retained austenite (RA) after directed energy deposition (DED). A heterogeneous distribution of Ti-rich oxy-carbo-nitrides (an Al-Ti-O-rich core with a TiN/TiC shell) and (Cr, Mo, W)-rich carbides is observed within the as-deposited microstructure. Aging at 700–850 °C promotes partial martensite-to-austenite reversion followed by retransformation during cooling, which reduces RA fraction (~11 vol.%), and induces the precipitation of M23C6 carbides. This process yields an improved strength-ductility balance, driven by a 50% reduction in RA and mild precipitation strengthening (~60 MPa) from dispersed carbides (~1.3 vol.%). Under hydrogen charging, the aged samples show a progressive fracture transition from microvoid coalescence to quasi-cleavage-dominated mixed fracture, with hydrogen embrittlement susceptibility of 0.81 (for 36 hours) and 0.43 (for 90 hours). Permeation analyses reveal that aging marginally increases the Dapp from 5.87×10–9 to 7.57×10–9 cm2/s, a result of reduced RA fraction. The low number density (~4×1019 1/m3) of M23C6 carbides minimally affects steady-state diffusivity, but they influence late-stage hydrogen desorption kinetics. The alloy exhibits a uniform passive film, offering excellent stability and resistance to pitting under anodic polarization. These findings demonstrate the significant potential of QT17−4+ as an advanced stainless steel, which combines high strength, good ductility, robust corrosion and hydrogen resistances.
- 23 February 2026
- Published by Springer Nature
- p. 374-382
Microstructure and Creep Resistance of an Additively Manufactured Al–Mn–Si Alloy
- 23 February 2026
- Published by Springer Nature
- p. 374-382
Microstructure and Creep Resistance of an Additively Manufactured Al–Mn–Si Alloy
- 23 February 2026
- Published by Springer Nature
- p. 287-294
Effects of Magnetic Field on Artificial Aging of Al–Mg–Zn–Cu Alloys Studied by Atom Probe Tomography
- 23 February 2026
- Published by Springer Nature
- p. 287-294
Effects of Magnetic Field on Artificial Aging of Al–Mg–Zn–Cu Alloys Studied by Atom Probe Tomography
- Top Cited Papers
- 27 January 2026
- Published by Elsevier in Computational Materials Science
- Vol. 265
Effects of alloying elements on carbon diffusion in the austenite (f.c.c.)- and ferrite (b.c.c.)-phases
- 27 January 2026
- Published by Elsevier in Computational Materials Science
- Vol. 265
Top Cited PapersEffects of alloying elements on carbon diffusion in the austenite (f.c.c.)- and ferrite (b.c.c.)-phases
- 29 November 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 950
Compressive-tensile yield asymmetry and aging-induced embrittlement in a selective laser melted 17-4 PH stainless steel
- 29 November 2025
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 950
Compressive-tensile yield asymmetry and aging-induced embrittlement in a selective laser melted 17-4 PH stainless steel
- Open Access
- 5 May 2024
- Published by Wiley in Advanced Materials Technologies
- Vol. 9 (15)
Process Parameter Optimization of Directed Energy Deposited QT17‐4+ Steel
The feasibility of using argon‐atomized QT 17‐4+ stainless steel powder for directed energy deposition (DED) additive manufacturing is studied. The QT 17‐4+ steel is a novel martensitic steel designed based on the compositional modification of the standard 17‐4 precipitation‐hardened (PH) stainless steel. This modification aims to achieve better mechanical properties of as‐deposited components compared to the heat‐treated wrought 17‐4PH steel. In this study, QT 17‐4+ steel powder is used for DED, for the first time. The influence of laser power, laser scan speed, powder feed rate, and hatch overlap on the density is studied. The central composite design is used to determine the experimental matrix of these factors. The response surface methodology is used to obtain the empirical statistical prediction model. Both columnar and equiaxed parent austenite grain structures are observed. X‐ray diffraction analyses reveal a decrease in the percentage of retained austenite from 19% in the powder to 5% after DED. The microhardness of the DED processed sample in the as‐deposited state is slightly higher than that of wrought 17‐4PH steel either solution‐annealed or H900‐aged. A higher 0.2% yield strength, a lower ultimate tensile strength, and lower elongation are observed for the vertically printed test sample, when compared to the horizontal one.
- 5 May 2024
- Published by Wiley in Advanced Materials Technologies
- Vol. 9 (15)
Open AccessProcess Parameter Optimization of Directed Energy Deposited QT17‐4+ Steel
The feasibility of using argon‐atomized QT 17‐4+ stainless steel powder for directed energy deposition (DED) additive manufacturing is studied. The QT 17‐4+ steel is a novel martensitic steel designed based on the compositional modification of the standard 17‐4 precipitation‐hardened (PH) stainless steel. This modification aims to achieve better mechanical properties of as‐deposited components compared to the heat‐treated wrought 17‐4PH steel. In this study, QT 17‐4+ steel powder is used for DED, for the first time. The influence of laser power, laser scan speed, powder feed rate, and hatch overlap on the density is studied. The central composite design is used to determine the experimental matrix of these factors. The response surface methodology is used to obtain the empirical statistical prediction model. Both columnar and equiaxed parent austenite grain structures are observed. X‐ray diffraction analyses reveal a decrease in the percentage of retained austenite from 19% in the powder to 5% after DED. The microhardness of the DED processed sample in the as‐deposited state is slightly higher than that of wrought 17‐4PH steel either solution‐annealed or H900‐aged. A higher 0.2% yield strength, a lower ultimate tensile strength, and lower elongation are observed for the vertically printed test sample, when compared to the horizontal one.
- 17 July 2023
- Published by Elsevier in Acta Materialia
- Vol. 257
Microstructural and mechanical properties of precipitation-strengthened Al-Mg-Zr-Sc-Er-Y-Si alloys
- 17 July 2023
- Published by Elsevier in Acta Materialia
- Vol. 257
Microstructural and mechanical properties of precipitation-strengthened Al-Mg-Zr-Sc-Er-Y-Si alloys