SBSara BinAhmed

Sara BinAhmed

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Sara BinAhmed has a total of 13 co-authors. Here are the top co-authors by number of shared publications:

  • Santiago Romero-Vargas Castrillón

    Institute for Infrastructure and Environment, School of Engineering, The University of Edinburgh, William Rankine Building, Thomas Bayes Road, Edinburgh EH9 3FG United Kingdom

    3 shared publications
  • Fouad Azizi

    B.&W. Bassatne Department of Chemical Engineering and Advanced Energy, M. Semaan Faculty of Engineering and Architecture, American University of Beirut, Beirut 1107 2020, Lebanon

    2 shared publications
  • Mahmoud Al-Hindi

    American University of Beirut

    2 shared publications
  • Zhaoxing Wang

    Department of Civil, Environmental, and Geo-Engineering, University of Minnesota, Twin Cities, 500 Pillsbury Dr. SE, Minneapolis, Minnesota 55455, United States

    2 shared publications
  • Anissa Hasane

    Department of Civil and Environmental Engineering, Norwegian University of Science and Technology , 7491 Trondheim, Norway

    1 shared publication
  • Aslan Mansurov

    Department of Civil, Environmental, and Geo-Engineering, University of Minnesota , 500 Pillsbury Dr SE, Minneapolis, Minnesota 55455, United States

    1 shared publication

Latest Publications

  • Open Access

    Do graphene oxide nanostructured coatings mitigate bacterial adhesion?

    by Karl Wuolo-Journey, Sara BinAhmed, Elise Linna, Santiago Romero-Vargas Castrillón

    Given its potent biocidal properties, graphene oxide (GO) holds promise as a building block of anti-microbial surfaces, with numerous potential environmental applications. Nonetheless, the extent to which GO-based coatings decrease bacterial adhesion propensity, a necessary requirement of low-fouling surfaces, remains unclear. Here we use AFM-based single-cell force spectroscopy (SCFS) to show that coatings comprising GO nanosheets bonded to a hydrophilic polymer brush mitigate adhesion of Pseudomonas fluorescens cells. We demonstrate low-adhesion GO coatings by grafting poly(acrylic acid) (PAA) to polyethersulfone (PES) substrates via self-initiated UV polymerization, followed by edge-tethering of GO to the PAA chains through amine coupling. We characterize the chemistry and interfacial properties of the unmodified PES, PAA-modified (PES–PAA), and GO-modified (PES–GO) substrates using ATR-FTIR, Raman spectroscopy, contact angle goniometry, and AFM to confirm the presence of PAA and covalently bonded GO on the substrates. Using SCFS we show that peak adhesion force distributions for PES–PAA (with mean adhesion force Peak = −0.13 nN) and PES–GO ( Peak = −0.11 nN) substrates are skewed towards weaker values compared to the PES control ( Peak = −0.18 nN). Our results show that weaker adhesion on PES–GO is due to a higher incidence of non-adhesive (repulsive) forces (45.9% compared to 22.2% over PES–PAA and 32.3% over PES), which result from steric repulsion afforded by the brush-like GO–PAA interface. Lastly, we show that attachment to the various substrates is due to interactions of proteinaceous adhesins whose force response is well described by the worm-like chain model of polymer elasticity.


  • Bacterial Adhesion to Graphene Oxide (GO)-Functionalized Interfaces Is Determined by Hydrophobicity and GO Sheet Spatial Orientation

    by Jinkai Xue, Sara BinAhmed, Zhaoxing Wang, Nathan G. Karp, Benjamin L. Stottrup, Santiago Romero-Vargas Castrillón


  • Bacterial Adhesion to Ultrafiltration Membranes: Role of Hydrophilicity, Natural Organic Matter, and Cell-Surface Macromolecules

    by Sara BinAhmed, Anissa Hasane, Zhaoxing Wang, Aslan Mansurov, Santiago Romero-Vargas Castrillón

    Insight into the mechanisms underlying bacterial adhesion is critical to the formulation of membrane biofouling control strategies. Using AFM-based single-cell force spectroscopy, we investigated the interaction between Pseudomonas fluorescens, a biofilm-forming bacterium, and polysulfone (PSF) ultrafiltration (UF) membranes to unravel the mechanisms underlying early stage membrane biofouling. We show that hydrophilic polydopamine (PDA) coatings decrease bacterial adhesion forces at short bacterium-membrane contact times. Further, we find that adhesion forces are weakened by the presence of natural organic matter (NOM) conditioning films, owing to the hydrophilicity of NOM. Investigation of the effect of adhesion contact time revealed that PDA coatings are less effective at preventing bioadhesion when the contact time is prolonged to 2–5 s, or when the membranes are exposed to bacterial suspensions under stirring. These results therefore challenge the notion that simple hydrophilic surface coatings are effective as a biofouling control strategy. Finally, we present evidence that adhesion to the UF membrane surface is mediated by cell-surface macromolecules (likely to be outer membrane proteins and pili) which, upon contacting the membrane, undergo surface-induced unfolding.


  • Open Access

    The effect of fast mixing conditions on the coagulation–flocculation process of highly turbid suspensions using liquid bittern coagulant

    by Sara BinAhmed, Georges Ayoub, Mahmoud Al-Hindi, Fouad Azizi

    The effect of fast mixing on floc formation and pollutant removal, using magnesium hydroxide as a coagulant, was investigated through characterization of relative strength and size of the formed flocs while operating at different mixing speeds and mixing times using a dynamic optical monitoring apparatus, and photometric dispersion analyzer (PDA2000). The parameters investigated included fast mixing speed (80, 100, and 120 rpm) and time (20, 40, and 60 s). Highly turbid kaolin clay suspensions (1213 ± 36 NTU) were alkalized using sodium hydroxide (NaOH) to pH values of 10.51 ± 0.02 at temperatures 20.7 ± 0.1°C, and liquid bittern (LB) was used as a coagulant. Fast mixing time had a clear effect on the flocs resistance to applied shear during the slow mixing phase. For all fast mixing times, 120 rpm caused the formation of largest flocs. Stronger flocs, indicated by the least change in flocculation index with time, required 60 s to form at all fast mixing speeds. Turbidity and TSS removal efficiencies are not only dependent on fast mixing speed but also on fast mixing time, such that higher fast mixing speeds were required for shorter mixing times


  • Coagulation of highly turbid suspensions using magnesium hydroxide: effects of slow mixing conditions

    by George M. Ayoub, Sara W. BinAhmed, Mahmoud Al-Hindi, Fouad Azizi

    Laboratory experiments were carried out to study the effects of slow mixing conditions on magnesium hydroxide floc size and strength and to determine the turbidity and total suspended solid (TSS) removal efficiencies during coagulation of highly turbid suspensions. A highly turbid kaolin clay suspension (1,213 ± 36 nephelometric turbidity units (NTU)) was alkalized to pH 10.5 using a 5 M NaOH solution; liquid bittern (LB) equivalent to 536 mg/L of Mg2+ was added as a coagulant, and the suspension was then subjected to previously optimized fast mixing conditions of 100 rpm and 60 s. Slow mixing speed (20, 30, 40, and 50 rpm) and time (10, 20, and 30 min) were then varied, while the temperature was maintained at 20.7 ± 1 °C. The standard practice for coagulation-flocculation jar test ASTM D2035-13 (2013) was followed in all experiments. Relative floc size was monitored using an optical measuring device, photometric dispersion analyzer (PDA 2000). Larger and more shear resistant flocs were obtained at 20 rpm for both 20- and 30-min slow mixing times; however, given the shorter duration for the former, the 20-min slow mixing time was considered to be more energy efficient. For slow mixing camp number (Gt) values in the range of 8,400–90,000, it was found that the mixing speed affected floc size and strength more than the time. Higher-turbidity removal efficiencies were achieved at 20 and 30 rpm, while TSS removal efficiency was higher for the 50-rpm slow mixing speed. Extended slow mixing time of 30 min yielded better turbidity and TSS removal efficiencies at the slower speeds.