Maria Fernanda Vieira Rocha
Research Subjects
Maria Fernanda Vieira Rocha has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Angélica de Cássia Oliveira Carneiro
Department of Forestry Engineering, Federal University of Viçosa, Viçosa 36570-000, MG, Brazil
4 shared publications - Ana Clara Caxito de Araújo
Universidade Federal de Lavras, Brasil
3 shared publications - Bárbara Luísa Corradi Pereira
Universidade Federal de Mato Grosso, Brasil
3 shared publications - Graziela Baptista Vidaurre
Departamento de Ciências Florestais e da Madeira, Universidade Federal do Espírito Santo, Jerônimo Monteiro, Brazil
3 shared publications - João Filipi Rodrigues Guimarães
Bracell Bahia Florestal , Alagoinhas , Bahia , Brazil
3 shared publications - Leonardo Sarno Soares Oliveira
Bracell Bahia Florestal , Alagoinhas , Bahia , Brazil
3 shared publications
Latest Publications
- Open Access
- 9 April 2026
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 80 (6) , 419-430
Impact of pre-hydrolysis kraft (PHK) conditions on young Eucalyptus clones’ unbleached pulp aiming at dissolving pulp production
The prehydrolysis kraft process (PHK) is the most widely used industrial method for producing dissolving pulp. Wood prehydrolysis involves the removal of hemicelluloses before kraft pulping, enabling the production of high-quality dissolving pulp. The process performance can be controlled by adjusting the time and temperature parameters. This study evaluates the effect of prehydrolysis intensity on the unbleached pulp quality of eucalyptus clones used for dissolving pulp production. Five trees from two eucalyptus clones ( Eucalyptus urophylla and E. urophylla × E. spp.), aged 3 and 5 years, cultivated in plantations located in Bahia, Brazil, were assessed. Hydrothermal pre-treatments were applied to wood chips under varying time and temperature conditions ( P -factor) to study its effect on kraft pulping and unbleached pulp properties such as yield, Kappa number, viscosity, brightness, pentosan content, and crystallinity index. Increasing the severity of the prehydrolysis process reduced the Kappa number and pentosan content, alongside an improvement of up to 8.6 % in pulp brightness and 7.2 % in the crystallinity index. These findings demonstrate the efficiency of optimized prehydrolysis conditions for dissolving pulp production, particularly for a P -factor of 432.
- 9 April 2026
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 80 (6) , 419-430
Open AccessImpact of pre-hydrolysis kraft (PHK) conditions on young Eucalyptus clones’ unbleached pulp aiming at dissolving pulp production
The prehydrolysis kraft process (PHK) is the most widely used industrial method for producing dissolving pulp. Wood prehydrolysis involves the removal of hemicelluloses before kraft pulping, enabling the production of high-quality dissolving pulp. The process performance can be controlled by adjusting the time and temperature parameters. This study evaluates the effect of prehydrolysis intensity on the unbleached pulp quality of eucalyptus clones used for dissolving pulp production. Five trees from two eucalyptus clones ( Eucalyptus urophylla and E. urophylla × E. spp.), aged 3 and 5 years, cultivated in plantations located in Bahia, Brazil, were assessed. Hydrothermal pre-treatments were applied to wood chips under varying time and temperature conditions ( P -factor) to study its effect on kraft pulping and unbleached pulp properties such as yield, Kappa number, viscosity, brightness, pentosan content, and crystallinity index. Increasing the severity of the prehydrolysis process reduced the Kappa number and pentosan content, alongside an improvement of up to 8.6 % in pulp brightness and 7.2 % in the crystallinity index. These findings demonstrate the efficiency of optimized prehydrolysis conditions for dissolving pulp production, particularly for a P -factor of 432.
- 13 January 2025
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 83 (1) , 1-11
Effect of the P-factor on the prehydrolysis process of eucalyptus wood for dissolving pulp production
- 13 January 2025
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 83 (1) , 1-11
Effect of the P-factor on the prehydrolysis process of eucalyptus wood for dissolving pulp production
- 21 August 2024
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 78 (10) , 562-569
Wood density and chemical composition variation of Eucalyptus urophylla clone in different environments
Variability in Eucalyptus wood density and chemical properties is crucial to understanding important factors for the forest-based industry, such as sampling methods and wood suitability as raw material. This study aimed to evaluate the basic density and chemical composition of the radial positions of young wood from the Eucalyptus urophylla clone grown under different precipitation levels. Trees from E. urophylla clonal plantations were collected in Inhambupe, Jandaíra and Itanagra, Bahia State, Brazil. Trees’ basic density and chemical composition (total extractive, lignin, hemicelluloses and α-cellulose) were determined based on the basal log of each tree, at four radial positions (1, 2, 3 and 4). It was found that the basic density and α-cellulose of wood are influenced by the cambial age and the site rainfall. There was greater increase in sections close to the bark (positions 1 and 4) and in more humid environments (sites Itanagra and Jandaríra). This finding highlights the association between wood basic density and chemical composition, mainly in the holocellulose content.
- 21 August 2024
- Published by Walter de Gruyter GmbH in Holzforschung
- Vol. 78 (10) , 562-569
Wood density and chemical composition variation of Eucalyptus urophylla clone in different environments
Variability in Eucalyptus wood density and chemical properties is crucial to understanding important factors for the forest-based industry, such as sampling methods and wood suitability as raw material. This study aimed to evaluate the basic density and chemical composition of the radial positions of young wood from the Eucalyptus urophylla clone grown under different precipitation levels. Trees from E. urophylla clonal plantations were collected in Inhambupe, Jandaíra and Itanagra, Bahia State, Brazil. Trees’ basic density and chemical composition (total extractive, lignin, hemicelluloses and α-cellulose) were determined based on the basal log of each tree, at four radial positions (1, 2, 3 and 4). It was found that the basic density and α-cellulose of wood are influenced by the cambial age and the site rainfall. There was greater increase in sections close to the bark (positions 1 and 4) and in more humid environments (sites Itanagra and Jandaríra). This finding highlights the association between wood basic density and chemical composition, mainly in the holocellulose content.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Revista Árvore
- Vol. 43 (4)
CHEMICAL AND ENERGETIC CHARACTERIZATION OF Eucalyptus grandis × Eucalyptus urophylla CLONES SUBJECT TO WIND DAMAGE
Wind damages are common in forest plantations and the use of this wood can minimize losses. The objective was to evaluate the chemical composition and the energetic potential of wood and charcoal from trees subject to wind damage. Eight (A to H) two-years-old Eucalyptus grandis × Eucalyptus urophylla clones were selected in a region where wind damage is frequent. The basic density, calorific value, chemical composition of wood and calorific value, immediate chemistry and gravimetric yield of charcoal were determined for all clones. Materials with high lignin content and low S/G ratio had higher gravimetric yield. The energy density of wood and charcoal showed high relationship with the basic and apparent relative density, respectively. All materials showed potential for bioenergy, but the clone E stood out with higher gravimetric yield and energy density.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Revista Árvore
- Vol. 43 (4)
Open AccessCHEMICAL AND ENERGETIC CHARACTERIZATION OF Eucalyptus grandis × Eucalyptus urophylla CLONES SUBJECT TO WIND DAMAGE
Wind damages are common in forest plantations and the use of this wood can minimize losses. The objective was to evaluate the chemical composition and the energetic potential of wood and charcoal from trees subject to wind damage. Eight (A to H) two-years-old Eucalyptus grandis × Eucalyptus urophylla clones were selected in a region where wind damage is frequent. The basic density, calorific value, chemical composition of wood and calorific value, immediate chemistry and gravimetric yield of charcoal were determined for all clones. Materials with high lignin content and low S/G ratio had higher gravimetric yield. The energy density of wood and charcoal showed high relationship with the basic and apparent relative density, respectively. All materials showed potential for bioenergy, but the clone E stood out with higher gravimetric yield and energy density.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Floresta e Ambiente
- Vol. 26 (3)
Do the Growing Conditions of Trees Influence the Wood Properties?
Currently, there is a little and sparse information about how the growing conditions influence the spatial variation of wood along the stem. Thus, the aim of this study was to compile the knowledge from literature in a manuscript for better understanding to what extent the growing conditions influence the spatial variation of wood properties in Eucalyptus plantations. The wood characteristics may present variations in their properties and can be caused by both genetic and environmental factors. However, how genetic and environmental factor acts on wood variation along the trunk is still unclear. Another point is that even with new genetic breeding programs, the mechanical properties of wood have not been considered in these programs, since the selection of new material is always based on the growing rate, cellulose and lignin content and wood density.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Floresta e Ambiente
- Vol. 26 (3)
Open AccessDo the Growing Conditions of Trees Influence the Wood Properties?
Currently, there is a little and sparse information about how the growing conditions influence the spatial variation of wood along the stem. Thus, the aim of this study was to compile the knowledge from literature in a manuscript for better understanding to what extent the growing conditions influence the spatial variation of wood properties in Eucalyptus plantations. The wood characteristics may present variations in their properties and can be caused by both genetic and environmental factors. However, how genetic and environmental factor acts on wood variation along the trunk is still unclear. Another point is that even with new genetic breeding programs, the mechanical properties of wood have not been considered in these programs, since the selection of new material is always based on the growing rate, cellulose and lignin content and wood density.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Floresta e Ambiente
- Vol. 26 (3)
Behavior of Juvenile and Mature Eucalyptus cloeziana Wood Subjected to Drastic Drying
This study aimed to evaluate the behavior of samples of juvenile and mature Eucalyptus cloeziana wood when subjected to the drying process, and the influence of the anatomy on that behavior. In order to do this, saturated specimens from this woods measuring 10 × 5 × 1 cm were subjected to drastic drying at 100 °C, where the drying rates and the end check scores in different steps of the process were obtained. The fibers and vessels morphology, initial moisture and basic density were analyzed to help understanding the data obtained in the drying test. The juvenile wood presented 26% higher drying rate and 21% smaller drying time, also 53% higher end check score. Smaller fibers length and fibers wall thickness, higher vessels frequency and smaller vessels diameter were associated with higher total drying rate and water adsorption, as well as with the higher end check score.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Floresta e Ambiente
- Vol. 26 (3)
Open AccessBehavior of Juvenile and Mature Eucalyptus cloeziana Wood Subjected to Drastic Drying
This study aimed to evaluate the behavior of samples of juvenile and mature Eucalyptus cloeziana wood when subjected to the drying process, and the influence of the anatomy on that behavior. In order to do this, saturated specimens from this woods measuring 10 × 5 × 1 cm were subjected to drastic drying at 100 °C, where the drying rates and the end check scores in different steps of the process were obtained. The fibers and vessels morphology, initial moisture and basic density were analyzed to help understanding the data obtained in the drying test. The juvenile wood presented 26% higher drying rate and 21% smaller drying time, also 53% higher end check score. Smaller fibers length and fibers wall thickness, higher vessels frequency and smaller vessels diameter were associated with higher total drying rate and water adsorption, as well as with the higher end check score.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Revista Árvore
- Vol. 43 (1)
TORREFIED BRIQUETTES OF SUGAR CANE BAGASSE AND EUCALYPTUS
Torrefaction and briquetting are two techniques that improve the quality of the biomass and facilitate direct use as fuel. The objective was to evaluate the effect of torrefaction temperature on the properties of the compound briquettes made from sugar cane bagasse and Eucalyptus sawdust. After sample preparation and particle analyses, briquettes were produced with the mixture of the two biomasses, a total of five compositions (0, 25, 50, 75 and 100%) at 120 °C and pressure of 1500 PSI. Subsequently, the briquettes were torrefied at temperatures of 180, 220 and 260 °C, for a period of 15 minutes. According to the results, both biomasses of Eucalyptus sawdust and sugar cane bagasse showed potential for the production of briquettes. The torrefaction reduced hygroscopicity and increased the calorific value of compound briquettes. The ideal composition for the production of briquettes is 100% Eucalyptus. The composition of 50% Eucalyptus + 50% sugar cane bagasse is also a great option, as some bagasse parameters were excellent. 260 °C was the best temperature to promote energy savings.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Revista Árvore
- Vol. 43 (1)
Open AccessTORREFIED BRIQUETTES OF SUGAR CANE BAGASSE AND EUCALYPTUS
Torrefaction and briquetting are two techniques that improve the quality of the biomass and facilitate direct use as fuel. The objective was to evaluate the effect of torrefaction temperature on the properties of the compound briquettes made from sugar cane bagasse and Eucalyptus sawdust. After sample preparation and particle analyses, briquettes were produced with the mixture of the two biomasses, a total of five compositions (0, 25, 50, 75 and 100%) at 120 °C and pressure of 1500 PSI. Subsequently, the briquettes were torrefied at temperatures of 180, 220 and 260 °C, for a period of 15 minutes. According to the results, both biomasses of Eucalyptus sawdust and sugar cane bagasse showed potential for the production of briquettes. The torrefaction reduced hygroscopicity and increased the calorific value of compound briquettes. The ideal composition for the production of briquettes is 100% Eucalyptus. The composition of 50% Eucalyptus + 50% sugar cane bagasse is also a great option, as some bagasse parameters were excellent. 260 °C was the best temperature to promote energy savings.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 23 (1) , 40-46
Nutrient accumulation in Eucalyptus bark at different population densities
The objective of this study was to quantify the accumulation of nutrients in the bark of four eucalyptus clones at 12 years-of-age, planted at different population densities, and the values were extrapolated to kg of nutrients per hectare. The experiment used randomized blocks in a 4 × 3 factorial design and three replications, with four Eucalyptus clones (2486, I182, I144, and GG100) planted at three population densities (416, 833, and 1111 trees ha-1). The rigorous cubage of three trees per plot was performed by collecting discs of bark at the following heights: diameter at breast height (1.30 m), 0, 25, 50, 75, and 100% of the commercial height of the stem. The bark discs of each tree were grouped and used to determine N, P, K, Ca, Mg, and S content, in addition to the basic density. The volume and dry mass of bark per tree was estimated and the accumulation of nutrients per tree ha-1 was estimated sequentially, for each population density. Analysis of variance and Tukey’s post-hoc tests verified that Ca showed the greatest accumulation in the bark, followed by N, K, S, Mg, and P. The increase in population density contributed to higher bark production and greater nutrient accumulation per hectare. However, this increase was not evident when comparing densities of 833 and 1111 trees ha-1.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 23 (1) , 40-46
Open AccessNutrient accumulation in Eucalyptus bark at different population densities
The objective of this study was to quantify the accumulation of nutrients in the bark of four eucalyptus clones at 12 years-of-age, planted at different population densities, and the values were extrapolated to kg of nutrients per hectare. The experiment used randomized blocks in a 4 × 3 factorial design and three replications, with four Eucalyptus clones (2486, I182, I144, and GG100) planted at three population densities (416, 833, and 1111 trees ha-1). The rigorous cubage of three trees per plot was performed by collecting discs of bark at the following heights: diameter at breast height (1.30 m), 0, 25, 50, 75, and 100% of the commercial height of the stem. The bark discs of each tree were grouped and used to determine N, P, K, Ca, Mg, and S content, in addition to the basic density. The volume and dry mass of bark per tree was estimated and the accumulation of nutrients per tree ha-1 was estimated sequentially, for each population density. Analysis of variance and Tukey’s post-hoc tests verified that Ca showed the greatest accumulation in the bark, followed by N, K, S, Mg, and P. The increase in population density contributed to higher bark production and greater nutrient accumulation per hectare. However, this increase was not evident when comparing densities of 833 and 1111 trees ha-1.
- Open Access
- 14 November 2018
- Published by FapUNIFESP (SciELO) in Revista Árvore
- Vol. 42 (5)
INFLUENCE OF PLANT SPACING ON THE BARK PROPERTIES OF A Eucalyptus CLONE
For several wood uses, such as pulp, paper and charcoal, the presence of the bark is undesirable, compromising production. Thus, this study aimed to evaluate the influence of different plant spacings on the properties of the bark of a clone of Eucalyptus grandis x E. camaldulensis at seven years of age at five different plant spacings. The wood discs were removed from the trees at 0, 25, 50, 75 and 100% of the commercial height; then we performed thickness, basic density, gross calorific value and mineral content analysis of bark. There were no significant differences among treatments for the bark gross calorific value and thickness. For the bark basic density, the highest values were found in trees planted in wider plant spacings and considering the mineral content, there was a significant difference only for P, Mn and Zn.
- 14 November 2018
- Published by FapUNIFESP (SciELO) in Revista Árvore
- Vol. 42 (5)
Open AccessINFLUENCE OF PLANT SPACING ON THE BARK PROPERTIES OF A Eucalyptus CLONE
For several wood uses, such as pulp, paper and charcoal, the presence of the bark is undesirable, compromising production. Thus, this study aimed to evaluate the influence of different plant spacings on the properties of the bark of a clone of Eucalyptus grandis x E. camaldulensis at seven years of age at five different plant spacings. The wood discs were removed from the trees at 0, 25, 50, 75 and 100% of the commercial height; then we performed thickness, basic density, gross calorific value and mineral content analysis of bark. There were no significant differences among treatments for the bark gross calorific value and thickness. For the bark basic density, the highest values were found in trees planted in wider plant spacings and considering the mineral content, there was a significant difference only for P, Mn and Zn.
- Open Access
- 30 August 2018
- Published by FapUNIFESP (SciELO) in Floresta e Ambiente
- Vol. 25 (4)
Wood Knots Influence the Modulus of Elasticity and Resistance to Compression
The objective of this study was to establish the correlation between the size of the wood knots and the modulus of elasticity (MOE) and the compressive strength (Fc) in Eucalyptus wood. 156 Eucalyptus urophylla samples with knots were separated into 3 classes (small, medium and large knots), and samples were selected from the same tree and submitted to the parallel fiber compression test for MOE and Fc determination. There was a significant difference between the MOE and Fc of the smaller knot class (Class 1) and the other classes with larger knots (Classes 2 and 3). In general, the larger the knot, the greater the difference between the MOE and Fc. Wood with small knots (8.31 mm2) presents stiffness and strength statistically equal to wood free of defects. Eucalyptus wood stiffness is more sensitive to the presence of knots than the strength when compared to clear wood samples.
- 30 August 2018
- Published by FapUNIFESP (SciELO) in Floresta e Ambiente
- Vol. 25 (4)
Open AccessWood Knots Influence the Modulus of Elasticity and Resistance to Compression
The objective of this study was to establish the correlation between the size of the wood knots and the modulus of elasticity (MOE) and the compressive strength (Fc) in Eucalyptus wood. 156 Eucalyptus urophylla samples with knots were separated into 3 classes (small, medium and large knots), and samples were selected from the same tree and submitted to the parallel fiber compression test for MOE and Fc determination. There was a significant difference between the MOE and Fc of the smaller knot class (Class 1) and the other classes with larger knots (Classes 2 and 3). In general, the larger the knot, the greater the difference between the MOE and Fc. Wood with small knots (8.31 mm2) presents stiffness and strength statistically equal to wood free of defects. Eucalyptus wood stiffness is more sensitive to the presence of knots than the strength when compared to clear wood samples.