JLJongwoo Lee

Jongwoo Lee

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jongwoo Lee has a total of 105 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A 28-nm CMOS 1-Chip In-Pixel Memory Backplane Circuit for 1800 × 1350 6652-PPI MicroLED AR Glasses With Per-Pixel Current Sensing and Compensation

    by Sunkwon Kim, Yongil Kwon, Youngkil Choi, Taehyun Kwon, Seongyoung Ryu, Sewhan Na, Kangjoo Kim, Uijong Song, Heejin Lee, Hyun-Wook Lim, et al.

  • High-Sensitivity, Low-Power IR-UWB Radar Transceiver With Self-Interference Resistance for Child Presence Detection and Precision Positioning

    by Hyun-Gi Seok, Wan Kim, Sinyoung Kim, Jae-Keun Lee, Geunhaeng Lee, Chanho Kim, Wonkang Kim, Jongpil Cho, Seungyong Bae, Youngsea Cho, et al.

    This article presents a radar-enabled impulse radio ultrawideband (IR-UWB) system by adopting a self-interference-resistant RF transceiver. It demonstrates that child presence detection (CPD) using IR-UWB radar is feasible through the implementation of a radar system that includes physical (PHY), media access control (MAC), and application (APP) processors. The RF transceiver shows high receiver (RX) sensitivity and high transmitter (TX) peak power with low power. In addition, a radar-dedicated TX is used to improve the TX signal isolation to the RX. To achieve the high RX chain gain and low noise figure (NF) of RX, an RX front end (RX-FE) low-noise amplifier (LNA) and voltage-to-current (V2I) with a 50% duty cycle local oscillator (LO) is implemented. Furthermore, a notch pulse shaping filter (PSF) technique is proposed to meet spectrum emission mask (SEM) specifications with low power consumption. An LNA with wide gain ranges is also proposed to improve the sensitivity and support various applications related to radar and positioning applications. The UWB transceiver achieves -96.5-dBm sensitivity at BPRF 6.81 Mb/s and 14-dBm TX peak power and supports radar operation with UWB channels 5 and 9.


  • An 8-nm 20-Gb/s/pin Single-Ended PAM-4 Transceiver With Pre/Post-Channel Switching Jitter Compensation and DQS-Driven Biasing

    by Kyunghwan Min, Jahoon Jin, Soo-Min Lee, Sodam Ju, Jisu Yook, Jihoon Lee, Yunji Hong, Sung-Sik Park, Sang-Ho Kim, Jongwoo Lee, et al.

    This letter presents a 20 Gb/s/pin single-ended PAM-4 transceiver implemented in an 8nm CMOS process, featuring an advanced switching jitter compensation (SWJC) technique and a DQS-driven amplifier bias generation method for a source-synchronous clocking system, aimed for next-generation low-power memory interfaces utilizing multi-level signaling. The proposed pre-channel SWJC (pre-SWJC) in the transmitter adjusts the input edge timing of the thermometer PAM-4 driver to control the transitions of the PAM-4 signal. This transition control advances the outermost transitions, thereby not only minimizing the switching jitter (SWJ) of the middle eye but also enhancing the effectiveness of the post-channel SWJC (post-SWJC) performed at the receiver. Ultimately, the comprehensive solution combining the proposed pre/post-SWJC improved the timing margin from 0.26 UI to 0.39 UI at a BER of 1e-12, with only a 4.5% increase in power consumption and a 0.59% area overhead. Additionally, the proposed DQS-driven biasing technique in the receiver supplies biases for the amplifiers in the data lanes by utilizing the common-mode feedback of the replica amplifier in the differential clock lane. This approach reduces variation sources compared to the self-biasing structure that uses common-mode feedback in the data lanes, thereby improving the standard deviation of the amplifier’s bias voltage and gain variation by 58.3%.


  • A 2.08-mW 64.4-dB SNDR 400-MS/s Pipelined- SAR ADC Using Mismatch and PVT Variation Tolerant Dynamically Biased Ring Amplifier in 8 nm

    by Yong Lim, Jaehoon Lee, Jongmi Lee, Kwangmin Lim, Seunghyun Oh, Jongwoo Lee

    In this article, we introduce a new dynamically biased ring amplifier that is tolerant to mismatch and PVT variation without requiring bias calibration, and we verify it in a 12-bit 400-MS/s pipelined-SAR analog-to-digital converter (ADC), fabricated in an 8-nm FinFET process. Our novel ring amplifier solves the biasing issues inherent in conventional ring amplifiers while maintaining the benefits of high gain, slew-based charging, and nearly rail-to-rail output swing. We also propose a technique to enhance the DC accuracy of a switched-capacitor common-mode feedback (CMFB) without consuming additional power, which we named feedback voltage sampling CMFB. Furthermore, we introduce a full-scale matching residue amplification technique for the prototype pipelined-SAR ADC to utilize the top-plate input sampling for the first-stage SAR ADC, resulting in faster and lower power conversion. The prototype ADC demonstrates the robustness of our dynamically biased ring amplifier to mismatch and PVT variation without any interstage gain, bias, or reference calibration, and achieves 64.4-dB SNDR and 77.6-dB SFDR for a low-frequency input while consuming 2.08 mW. This measured performance is equivalent to Walden and Schreier FoMs of 3.8 fJ/conversion $\cdot$ step and 174.2 dB, respectively.


  • A Computational Digital LDO With Distributed Power-Gating Switches and Time-Based Fast-Transient Controller for Mobile SoC Application

    by Dongha Lee, Seki Kim, Takahiro Nomiyama, Dong-Hoon Jung, Dongsu Kim, Jongwoo Lee

    This letter introduces a 10A computational digital LDO (CDLDO) for mobile SoC application specifically targeting a big CPU core. The proposed CDLDO eliminates the power-FET area overhead by re-using power gating switches (PGSs) already distributed throughout the entire CPU. The CDLDO employs a time-based exponential control (TEC) with a slope detector to achieve fast-transient response and improve stability. Furthermore, a step-back and a negative-step control are introduced to mitigate the effect of the propagation delay between the controller and the PGSs. Additionally, a pre-computational scheme significantly reduces calculation time and relaxes timing constraints during synthesis. The proposed CDLDO is implemented in 3nm GAAFET CMOS process. An implemented IC of eight distributed CDLDO units provides a maximum load current of 10A with a current density of 263A/mm2. The CDLDO shows 94mV droop under 6.5A/1ns load transition.


  • A 4-nm 16-Gb/s/pin Single-Ended PAM-4 Parallel Transceiver With Switching-Jitter Compensation and Transmitter Optimization

    by Jahoon Jin, Soo-Min Lee, Kyunghwan Min, Sodam Ju, Jihoon Lim, Jisu Yook, Jihoon Lee, Hyunsu Chae, Kwonwoo Kang, Yunji Hong, et al.

    This article presents a 16-Gb/s/pin 0.764-pJ/b single-ended four-level pulse-amplitude modulation (PAM-4) transceiver in a 4-nm CMOS process. A switching-jitter compensation technique is proposed in the receiver (RX) to improve timing margins from 0.31 to 0.37 UI at 16 Gb/s, as it adjusts transition slope of the front-end outputs. To compensate for signal-to-noise ratio (SNR) degradation in a PAM-4 signal, relaxed impedance matching is used, where 20 $\Omega$ is used as a transmitter (TX) impedance instead of 50 $\Omega$ . To maximize eye openings further, fractionally spaced feedforward equalization (FS-FFE) is used with a tap spacing of 0.8 UI. The relaxed termination scheme along with FS-FFE improves eye openings by 2.25 times compared with the conventional design using a 50- $\Omega$ TX impedance with 1-UI spacing FFE.


  • A Single-Path Digital-IF Receiver Supporting Inter/Intra 5-CA with a Single Integer LO-PLL in 14nm CMOS FinFET

    by Barosaim Sung, Hyun-Gi Seok, Jaekwon Kim, Jaehoon Lee, Taejin Jang, Ilhoon Jang, Youngmin Kim, Anna Yu, Jong-Hyun Jang, Jiyoung Lee, et al.

    The expansion of information and communication technologies has led us to the invention of 5 th -generation (5G) communications. However, as an effort to overcome the insufficient frequency-band resource in FR1, telecommunication companies are continuously securing additional re-farming bands in FR1, and they are extending maximum throughput by applying Carrier Aggregation/E-UTRA NR Dual connectivity (CA/EN-DC) based on many fragment bands as shown in Fig. 27.5.1. For example, a major telecommunication company supports CA/EN-DC of the B1, B3, B5, B7 (1), B7 (2), and n78 bands, which require more than 20 RX paths considering the antenna diversity and 4x4 MIMO needed for maximum throughput. As the demands for spectrum re-farming increase, more fragment bands are used, and the required numbers of RX paths also increase accordingly in a conventional direct-conversion-receiver (DCR) architecture. In addition, to support the various fragment bands, multiple front-end modules (FEMs) are required and each FEM needs to be highly complexed with higher-performance multiplexers such as octaplexers or hexaplexers to maintain TX-RX isolation for TX desensitization from IIP2 as shown in Fig. 27.5.1. When B1 TX and RX are activated with B3 RX simultaneously, the isolation between the B1 TX and B3 RX path is more difficult to achieve than that between the B1 TX and RX path due to the reduced duplex spacing (i.e., 40MHz from 130MHz). Also, a local-oscillator (LO) leakage power from in-band LO frequency as well as leakage powers from the adjacent LO harmonics are added to the DC offset of receiver chains. These issues can be relaxed by a multiple-channel-processing receiver with IF conversion such as a software-defined-radio (SDR) receiver or by cognitive radio (CR) receivers that can break through the shortage of FR1 band by searching and adapting unoccupied bands in real time.


  • Adaptive 5G Architecture for an mmWave Antenna Front-End Package Consisting of Tunable Matching Network and Surface-Mount Technology

    by Jaehyun Choi, Dooseok Choi, Jongwoo Lee, Woonbong Hwang, Wonbin Hong

    Adaptive 5G architecture consisting of three functional sections (four antenna components, tunable matching network (TMN), and radio frequency (RF) front-end package) is proposed, analyzed and verified. In the 5G mmWave spectrum, the RF performance is highly dependent on the specific antenna package technology. However, compact antenna packages oftentimes result in undesired interference between the antenna elements. This eventually leads to severe RF performance degradation. For the first time in literature, a mmWave 5G RFIC and the TMN are integrated for efficient operation that is applicable to real-life 5G mobile devices. Moreover, the proposed antenna-in-package (AiP) architecture enables independent frequency control at multiple frequencies. The proposed solution is simulated and measured at the system level. As a result, the devised AiP solution exhibits a simulated effective isotropic radiated power (EIRP) of 22.05–23.96 dBm at the cumulative distribution function (CDF) of 50% by applying the conducted power of 17 dBm (per channel), and the peak gain of the antenna exhibits 13.7 dBi at 27 GHz (state A) and 12.6 dBi at 28 GHz (state B) with an amplifier having an output power of 5 dBm.


  • NB-IoT and GNSS All-In-One System-On-Chip Integrating RF Transceiver, 23-dBm CMOS Power Amplifier, Power Management Unit, and Clock Management System for Low Cost Solution

    by Jongsoo Lee, Jaeyeol Han, Chi-Lun Lo, Jongmi Lee, Wan Kim, Seungjin Kim, Byoungjoong Kang, Juyoung Han, Sangdon Jung, Takahiro Nomiyama, et al.

    This article presents a fully integrated stand-alone narrowband Internet-of-Things (NB-IoT) and global navigation satellite system (GNSS) system-on-chip (SoC). It aims for an all-in-one system to integrate all necessary blocks such as an RF transceiver, a power management system (PMIP), and a clock management system and to save a bills-of-material (BOM) cost. An RF transceiver is integrated to support multi-band cellular IoT and GNSS with a CMOS RF power amplifier transmitting 23-dBm output power. A PMIP, including bucks, a boost, and low-dropout regulators (LDOs), is integrated to support coin cell or AAA battery and to support a wide input supply voltage range from 2.5 to 5 V. In addition, clock management system is embedded with a digitally controlled crystal oscillator (DCXO), a relaxation oscillator (RCO), and temperature sensor units (TSUs). It is fabricated in a standard 28-nm CMOS process and its size is 24.6 mm². The power consumption of always-on-block is 15 μW, and the sleep current consumption is less than 10 μA at 3.8 V.


  • A Sub-6-GHz 5G New Radio RF Transceiver Supporting EN-DC With 3.15-Gb/s DL and 1.27-Gb/s UL in 14-nm FinFET CMOS

    by Jongwoo Lee, Ki Yong Son, Hyungsun Lim, Daechul Jeong, Ilyong Jong, Sanghyun Baek, Jae Hoon Lee, Ronghua Ni, Yongrong Zuo, Chih-Wei Yao, et al.

    The world's first single-chip RF transceiver to support 5G sub-6-GHz new radio (NR) and long-term evolution (LTE) E-UTRA New Radio-Dual Connectivity (EN-DC) in 14-nm FinFET CMOS technology is presented. The single-chip transceiver integrates identical primary and diversity receivers (RXs) with seven pipelines for supporting four inter-band carrier aggregation (CA) with three 4 x 4 MIMO, two independent transmitter (TX) chains, eight frequency synthesizers for RX and TX, and on-chip digitally controlled crystal oscillator (DCXO) to reduce the phase noise and bill of material (BOM) cost. The receiver features 12 single-ended low-noise amplifiers (LNAs) with wideband characteristics. With the help of the proposed pipeline structure and frequency-band switchable transformer, the die size can be reduced despite covering the whole frequency range from 2G to sub-6-GHz 5G NR. It achieves the noise figure (NF) from 6.5 to 9.3 dB, +3-dBm out-of-band (OOB) IIP3, more than +70-dBm OOB IIP2 after calibration. For the transmitter, low RX-band noise and harmonic suppression technique are applied to support surface acoustic wave (SAW)-less architecture, and the bandwidth control of the baseband filter is implemented for the digital pre-distortion (DPD) operation of 100-MHz BW in NR transmit data. The measured error vector magnitudes (EVMs) in 4G and 5G bands of n79 are -39.5 dB at +4-dBm output power and -33.9 dB at +3.06-dBm output power, respectively, and the measured RX-band noise of 2G is -163 dBc at 20-MHz offset. The RX consumes 18 mW at LTE 1-CA mode and the TX consumes 350 mW at n79.