YWYuqiao Wang

Yuqiao Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yuqiao Wang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Research on the Treatment of Chronic Urticaria with Mahuang Lianqiao Chixiaodou Decoction Based on Xuanfu Theory

    by Ma Chaochao, Wang Yuqiao, Wang Sinong

    Chronic urticaria is a dermatological allergic disease with an uncertain etiology and pathogenesis. It presents challenges such as high recurrence rate and impact on the physical and mental health of patients. Traditional Chinese medicine has been continuously exploring the understanding of this disease, of which the Xuanfu theory suggests a close correlation between the pathogenesis of chronic urticaria and Xuanfu obstruction. By analyzing and utilizing the Ma Huang Lian Qiao Chi Xiao Dou Tang in the treatment of chronic urticaria, the aim is to open up the Xuanfu, restore its normal function, regulate its opening and closing, and expel pathogenicfactors from the pores of the Xuanfu. This treatment approach aims to enrich the theoretical basis of skin disease treatment. A clinical case study is also attached.

  • Open Access

    Nonlinear Torsional Vibration Analysis and Nonlinear Feedback Control of Complex Permanent Magnet Semidirect Drive Cutting System in Coal Cutters

    by Lianchao Sheng, Wei Li, Gaifang Xin, Yuqiao Wang, Mengbao Fan, Xuefeng Yang

    The semidirect drive cutting transmission system of coal cutters is prone to unstable torsional vibration when the resistance values of its driving permanent magnet synchronous motor (PMSM) are affected by changes in temperatures and tough conditions. Besides, the system has the properties of complex electromechanically coupling such as the coupling between electrical parameters and mechanical parameters. Therefore, in this study, the nonlinear torsional vibration equation was established on the basis of the Lagrange‐Maxwell theory. Moreover, in light of the nonlinear dynamic bifurcation theory, the system stability was analyzed by taking the resistance value of power motor as the bifurcation parameter. In addition, the influence of subcritical bifurcation on the torsional vibration was studied by investigating the necessary and sufficient conditions for dynamic Hopf bifurcation and classifying the bifurcation types. At last, in order to suppress destabilizing oscillation induced by Hopf bifurcation, the nonlinear feedback controller was constructed, with the introduction of feedback from the motor velocity as well as the selection of voltage value on the q shaft as the controlled variable. Meanwhile, the three‐order normal form and controlling parameters of the system were obtained with the aid of the multiple scales method and the harmonic balance method. In this way, the Hopf bifurcation point was transferred to control the stability of Hopf bifurcation and the amplitude of limit cycle, thus guaranteeing reliable and safe operation of the system. The numerical simulation results indicate that the designed controller boosts an ideal controlling effect.


  • Optimal placement and active vibration control for piezoelectric smart flexible manipulators using modal H2 norm

    by En Lu, Wei Li, Xuefeng Yang, Yuqiao Wang, Yufei Liu

    The optimal placement and active vibration control for piezoelectric smart single flexible manipulator are investigated in this study. Based on the assumed mode method and Hamilton’s principle, the dynamic equation of the piezoelectric smart single flexible manipulator is established. Then, the singular perturbation method is adopted and the coupled dynamic equation is decomposed into slow (rigid) and fast (flexible) subsystems. After that, the couple optimal placement criterion of piezoelectric actuators is proposed on the base of modal H2 norm of the fast subsystem and the change rate of natural frequencies. Using an improved particle swarm optimization algorithm, the optimal placement of piezoelectric actuators is realized. Subsequently, in order to verify the validity and feasibility of the presented optimal placement criterion, the composite controller is designed for the active vibration control of the piezoelectric smart single flexible manipulator. Finally, numerical simulations and experiments are presented. The results demonstrate that the piezoelectric smart single flexible manipulator system has a better single modal controllability and observability and has a good result on the vibration suppression using the optimization results of actuators. The proposed optimal placement criterion and method are feasible and effective.


  • Stochastic noise identification in a stray current sensor

    by Shao-Yi Xu, Fang-Fang Xing, Wei Li, Yu-Qiao Wang


  • Open Access

    Dynamic Model and Vibration Characteristics of Planar 3-RRR Parallel Manipulator with Flexible Intermediate Links considering Exact Boundary Conditions

    by Lianchao Sheng, Wei Li, Yuqiao Wang, Mengbao Fan, Xuefeng Yang

    Due to the complexity of the dynamic model of a planar 3-RRR flexible parallel manipulator (FPM), it is often difficult to achieve active vibration control algorithm based on the system dynamic model. To establish a simple and efficient dynamic model of the planar 3-RRR FPM to study its dynamic characteristics and build a controller conveniently, firstly, considering the effect of rigid-flexible coupling and the moment of inertia at the end of the flexible intermediate link, the modal function is determined with the pinned-free boundary condition. Then, considering the main vibration modes of the system, a high-efficiency coupling dynamic model is established on the basis of guaranteeing the model control accuracy. According to the model, the modal characteristics of the flexible intermediate link are analyzed and compared with the modal test results. The results show that the model can effectively reflect the main vibration modes of the planar 3-RRR FPM; in addition the model can be used to analyze the effects of inertial and coupling forces on the dynamics model and the drive torque of the drive motor. Because this model is of the less dynamic parameters, it is convenient to carry out the control program.