Hiraku Toida
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hiraku Toida has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
Kosuke Kakuyanagi
NTT Basic Research Laboratories, NTT Corporation, Atsugi, Japan
10 shared publicationsShiro Saito
NTT Basic Research Laboratories, NTT Corporation, 3-1 Morinosato-Wakamiya, Atsugi, Kanagawa 243-0198, Japan
8 shared publicationsYuichiro Matsuzaki
Research Center for Emerging Computing Technologies, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568, Japan
8 shared publicationsImran Mahboob
NTT Basic Research Laboratories, NTT Corporation, Atsugi, Japan
4 shared publications- Shiro Saito
NTT Basic Research Laboratories, NTT Corporation, Atsugi, Japan
4 shared publications - Leonid V. Abdurakhimov
NTT Basic Research Laboratories, NTT Corporation, 3-1 Morinosato-Wakamiya, Atsugi, Kanagawa 243-0198, Japan
3 shared publications
Latest Publications
- 8 June 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (23)
Geometric dependence of critical-current variation in Al/AlO x /Al Josephson junctions: A model-based analysis
Achieving uniform critical current across Josephson junctions is essential for the large-scale integration of superconducting quantum circuits. In this work, we statistically analyzed the variation of the critical current of Al/AlOx/Al junctions using room-temperature tunnel resistance statistics and identified the dominant contribution among the modeled sources of the variation based on their dependence on geometry and deposition conditions of junctions. Our model-based analysis reveals that fluctuations in the Al film thickness play the dominant role among the modeled contributing factors. Based on this analysis, we found that, in Dolan-bridge double-angle deposition, adopting a deposition angle of 30° for bilayer junctions significantly improves uniformity, yielding a relative standard deviation of 1.2% (0.5%) across a 9.75 mm (1.5 mm) square region.
- 8 June 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (23)
Geometric dependence of critical-current variation in Al/AlO x /Al Josephson junctions: A model-based analysis
Achieving uniform critical current across Josephson junctions is essential for the large-scale integration of superconducting quantum circuits. In this work, we statistically analyzed the variation of the critical current of Al/AlOx/Al junctions using room-temperature tunnel resistance statistics and identified the dominant contribution among the modeled sources of the variation based on their dependence on geometry and deposition conditions of junctions. Our model-based analysis reveals that fluctuations in the Al film thickness play the dominant role among the modeled contributing factors. Based on this analysis, we found that, in Dolan-bridge double-angle deposition, adopting a deposition angle of 30° for bilayer junctions significantly improves uniformity, yielding a relative standard deviation of 1.2% (0.5%) across a 9.75 mm (1.5 mm) square region.
- Open Access
- 6 February 2023
- Published by Springer Nature in Communications Physics
- Vol. 6 (1) , 1-6
Magnetometry of neurons using a superconducting qubit
Iron plays important physiological and pathological roles in the human body. However, microscopic analysis including redox status by a conventional electron spin resonance (ESR) spectrometer is difficult due to limited spatial resolution and sensitivity. Here we demonstrate magnetometry of cultured neurons on a polymeric film using a superconducting flux qubit that works as a sensitive magnetometer in a microscale area towards realizing ESR spectroscopy. By changing temperature (12.5–200 mK) and a magnetic field (2.5–12.5 mT), we observe a clear magnetization signal from the neurons that is well above the control magnetometry of the polymeric film itself. From ESR spectrum measured at 10 K, the magnetization signal is identified to originate from electron spins of iron ions in neurons. This technique to detect a bio-spin system can be extended to achieve ESR spectroscopy at the single-cell level, which will give the spectroscopic fingerprint of cells.
- 6 February 2023
- Published by Springer Nature in Communications Physics
- Vol. 6 (1) , 1-6
Open AccessMagnetometry of neurons using a superconducting qubit
Iron plays important physiological and pathological roles in the human body. However, microscopic analysis including redox status by a conventional electron spin resonance (ESR) spectrometer is difficult due to limited spatial resolution and sensitivity. Here we demonstrate magnetometry of cultured neurons on a polymeric film using a superconducting flux qubit that works as a sensitive magnetometer in a microscale area towards realizing ESR spectroscopy. By changing temperature (12.5–200 mK) and a magnetic field (2.5–12.5 mT), we observe a clear magnetization signal from the neurons that is well above the control magnetometry of the polymeric film itself. From ESR spectrum measured at 10 K, the magnetization signal is identified to originate from electron spins of iron ions in neurons. This technique to detect a bio-spin system can be extended to achieve ESR spectroscopy at the single-cell level, which will give the spectroscopic fingerprint of cells.
- Open Access
- 21 December 2022
- Published by American Physical Society (APS) in PRX Quantum
- Vol. 3 (4) , 040332
Identification of Different Types of High-Frequency Defects in Superconducting Qubits
Parasitic two-level-system (TLS) defects are one of the major factors limiting the coherence times of superconducting qubits. Although there has been significant progress in characterizing basic parameters of TLS defects, exact mechanisms of interactions between a qubit and various types of TLS defects remained largely unexplored due to the lack of experimental techniques able to probe the form of qubit-defect couplings. Here we present an experimental method of TLS defect spectroscopy using a strong qubit drive that allowed us to distinguish between various types of qubit-defect interactions. By applying this method to a capacitively shunted flux qubit, we detected a rare type of TLS defect with a nonlinear qubit-defect coupling due to critical-current fluctuations, as well as conventional TLS defects with a linear coupling to the qubit caused by charge fluctuations. The presented approach could become the routine method for high-frequency defect inspection and quality control in superconducting qubit fabrication, providing essential feedback for fabrication process optimization. The reported method is a powerful tool to uniquely identify the type of noise fluctuations caused by TLS defects, enabling the development of realistic noise models relevant to noisy intermediate-scale quantum computing and fault-tolerant quantum control.
- 21 December 2022
- Published by American Physical Society (APS) in PRX Quantum
- Vol. 3 (4) , 040332
Open AccessIdentification of Different Types of High-Frequency Defects in Superconducting Qubits
Parasitic two-level-system (TLS) defects are one of the major factors limiting the coherence times of superconducting qubits. Although there has been significant progress in characterizing basic parameters of TLS defects, exact mechanisms of interactions between a qubit and various types of TLS defects remained largely unexplored due to the lack of experimental techniques able to probe the form of qubit-defect couplings. Here we present an experimental method of TLS defect spectroscopy using a strong qubit drive that allowed us to distinguish between various types of qubit-defect interactions. By applying this method to a capacitively shunted flux qubit, we detected a rare type of TLS defect with a nonlinear qubit-defect coupling due to critical-current fluctuations, as well as conventional TLS defects with a linear coupling to the qubit caused by charge fluctuations. The presented approach could become the routine method for high-frequency defect inspection and quality control in superconducting qubit fabrication, providing essential feedback for fabrication process optimization. The reported method is a powerful tool to uniquely identify the type of noise fluctuations caused by TLS defects, enabling the development of realistic noise models relevant to noisy intermediate-scale quantum computing and fault-tolerant quantum control.
- 3 September 2020
- Published by American Physical Society (APS) in Physical Review B
- Vol. 102 (9) , 094502
Control of the transition frequency of a superconducting flux qubit by longitudinal coupling to the photon number degree of freedom in a resonator
We control the transition frequency of a superconducting flux qubit coupled to a frequency-tunable resonator comprising a direct current superconducting quantum interference device (dc SQUID) by microwave driving. The dc SQUID mediates the coupling between microwave photons in the resonator and a flux qubit. The polarity of the frequency shift depends on the sign of the flux bias for the qubit and can be both positive and negative. The absolute value of the frequency shift becomes larger by increasing the photon number in the resonator. These behaviors are reproduced by a model considering the magnetic interaction between the flux qubit and dc SQUID. The tuning range of the transition frequency of the flux qubit reaches . The effect of photon number fluctuation in the resonator to the dephasing rate of the flux qubit is also discussed.- 3 September 2020
- Published by American Physical Society (APS) in Physical Review B
- Vol. 102 (9) , 094502
Control of the transition frequency of a superconducting flux qubit by longitudinal coupling to the photon number degree of freedom in a resonator
We control the transition frequency of a superconducting flux qubit coupled to a frequency-tunable resonator comprising a direct current superconducting quantum interference device (dc SQUID) by microwave driving. The dc SQUID mediates the coupling between microwave photons in the resonator and a flux qubit. The polarity of the frequency shift depends on the sign of the flux bias for the qubit and can be both positive and negative. The absolute value of the frequency shift becomes larger by increasing the photon number in the resonator. These behaviors are reproduced by a model considering the magnetic interaction between the flux qubit and dc SQUID. The tuning range of the transition frequency of the flux qubit reaches . The effect of photon number fluctuation in the resonator to the dephasing rate of the flux qubit is also discussed.- 3 September 2020
- Published by American Physical Society (APS) in Physical Review B
- Vol. 102 (10) , 100502
Driven-state relaxation of a coupled qubit-defect system in spin-locking measurements
It is widely known that spin-locking noise spectroscopy is a powerful technique for the characterization of low-frequency noise mechanisms in superconducting qubits. Here we show that the relaxation rate of the driven spin-locking state of a qubit can be significantly affected by the presence of an off-resonant high-frequency two-level-system defect. Thus, both low- and high-frequency defects should be taken into account in the interpretation of spin-locking measurements and other types of driven-state noise spectroscopy.
- 3 September 2020
- Published by American Physical Society (APS) in Physical Review B
- Vol. 102 (10) , 100502
Driven-state relaxation of a coupled qubit-defect system in spin-locking measurements
It is widely known that spin-locking noise spectroscopy is a powerful technique for the characterization of low-frequency noise mechanisms in superconducting qubits. Here we show that the relaxation rate of the driven spin-locking state of a qubit can be significantly affected by the presence of an off-resonant high-frequency two-level-system defect. Thus, both low- and high-frequency defects should be taken into account in the interpretation of spin-locking measurements and other types of driven-state noise spectroscopy.
- Open Access
- 11 May 2020
- Published by AIP Publishing in Applied Physics Letters
- Vol. 116 (19) , 194001
Electron spin resonance with up to 20 spin sensitivity measured using a superconducting flux qubit
We report on electron spin resonance spectroscopy measurements using a superconducting flux qubit with a sensing volume of 6 fl. The qubit is read out using a frequency-tunable Josephson bifurcation amplifier, which leads to an inferred measurement sensitivity of about 20 spins in a 1 s measurement. This sensitivity represents an order of magnitude improvement when compared to flux-qubit schemes using a direct current-superconducting quantum interference device switching readout. Furthermore, noise spectroscopy reveals that the sensitivity is limited by flicker ( ) flux noise.- 11 May 2020
- Published by AIP Publishing in Applied Physics Letters
- Vol. 116 (19) , 194001
Open AccessElectron spin resonance with up to 20 spin sensitivity measured using a superconducting flux qubit
We report on electron spin resonance spectroscopy measurements using a superconducting flux qubit with a sensing volume of 6 fl. The qubit is read out using a frequency-tunable Josephson bifurcation amplifier, which leads to an inferred measurement sensitivity of about 20 spins in a 1 s measurement. This sensitivity represents an order of magnitude improvement when compared to flux-qubit schemes using a direct current-superconducting quantum interference device switching readout. Furthermore, noise spectroscopy reveals that the sensitivity is limited by flicker ( ) flux noise. - 1 May 2020
- Published by American Physical Society (APS) in Physical Review A
- Vol. 101 (5) , 052303
Architecture to achieve nuclear magnetic resonance spectroscopy with a superconducting flux qubit
We theoretically analyze the performance of the nuclear magnetic resonance (NMR) spectroscopy with a superconducting flux qubit (FQ). Such NMR with the FQ is attractive because of the possibility to detect the relatively small number of nuclear spins in a local region () with low temperatures () and low magnetic fields (), in which other types of quantum sensing schemes cannot easily be accessed. A sample containing nuclear spins is directly attached on the FQ, and the FQ is used as a magnetometer to detect magnetic fields from the nuclear spins. Especially, we consider two types of approaches to NMR with the FQ. One of them is to use spatially inhomogeneous excitations of the nuclear spins, which are induced by a spatially asymmetric driving with radio-frequency (rf) pulses. Such an inhomogeneity causes a change in the dc magnetic flux penetrating a loop of the FQ, which can be detected by a standard Ramsey measurement on the FQ. The other approach is to use a dynamical decoupling on the FQ to measure ac magnetic fields induced by Larmor precession of the nuclear spins. In this case, neither a spin excitation nor a spin polarization is required since the signal comes from fluctuating magnetic fields of the nuclear spins. We calculate the minimum detectable density (number) of the nuclear spins for the FQ with experimentally feasible parameters. We show that the minimum detectable density (number) of the nuclear spins with these approaches is around () with an accumulation time of 1 s.- 1 May 2020
- Published by American Physical Society (APS) in Physical Review A
- Vol. 101 (5) , 052303
Architecture to achieve nuclear magnetic resonance spectroscopy with a superconducting flux qubit
We theoretically analyze the performance of the nuclear magnetic resonance (NMR) spectroscopy with a superconducting flux qubit (FQ). Such NMR with the FQ is attractive because of the possibility to detect the relatively small number of nuclear spins in a local region () with low temperatures () and low magnetic fields (), in which other types of quantum sensing schemes cannot easily be accessed. A sample containing nuclear spins is directly attached on the FQ, and the FQ is used as a magnetometer to detect magnetic fields from the nuclear spins. Especially, we consider two types of approaches to NMR with the FQ. One of them is to use spatially inhomogeneous excitations of the nuclear spins, which are induced by a spatially asymmetric driving with radio-frequency (rf) pulses. Such an inhomogeneity causes a change in the dc magnetic flux penetrating a loop of the FQ, which can be detected by a standard Ramsey measurement on the FQ. The other approach is to use a dynamical decoupling on the FQ to measure ac magnetic fields induced by Larmor precession of the nuclear spins. In this case, neither a spin excitation nor a spin polarization is required since the signal comes from fluctuating magnetic fields of the nuclear spins. We calculate the minimum detectable density (number) of the nuclear spins for the FQ with experimentally feasible parameters. We show that the minimum detectable density (number) of the nuclear spins with these approaches is around () with an accumulation time of 1 s.- Open Access
- 23 December 2019
- Published by AIP Publishing in Applied Physics Letters
- Vol. 115 (26) , 262601
A long-lived capacitively shunted flux qubit embedded in a 3D cavity
We report the experimental realization of a 3D capacitively shunt superconducting flux qubit with long coherence times. At the optimal flux bias point, the qubit demonstrates energy relaxation times in the range of 60–90 μs and a Hahn-echo coherence time of about 80 μs, which can be further improved by dynamical decoupling. Qubit energy relaxation can be attributed to quasiparticle tunneling and unwanted two-level-system defects, while qubit dephasing is caused by flux noise away from the optimal point. Our results show that 3D c-shunt flux qubits demonstrate improved performance over other types of flux qubits, which is advantageous for applications such as quantum magnetometry and spin sensing.
- 23 December 2019
- Published by AIP Publishing in Applied Physics Letters
- Vol. 115 (26) , 262601
Open AccessA long-lived capacitively shunted flux qubit embedded in a 3D cavity
We report the experimental realization of a 3D capacitively shunt superconducting flux qubit with long coherence times. At the optimal flux bias point, the qubit demonstrates energy relaxation times in the range of 60–90 μs and a Hahn-echo coherence time of about 80 μs, which can be further improved by dynamical decoupling. Qubit energy relaxation can be attributed to quasiparticle tunneling and unwanted two-level-system defects, while qubit dephasing is caused by flux noise away from the optimal point. Our results show that 3D c-shunt flux qubits demonstrate improved performance over other types of flux qubits, which is advantageous for applications such as quantum magnetometry and spin sensing.
- Open Access
- 29 March 2019
- Published by Springer Nature in Communications Physics
- Vol. 2 (1) , 1-7
Electron paramagnetic resonance spectroscopy using a single artificial atom
Electron paramagnetic resonance (EPR) spectroscopy is an important technology in physics, chemistry, materials science, and biology. Sensitive detection with a small sample volume is a key objective in these areas, because it is crucial, for example, for the readout of a highly packed spin based quantum memory or the detection of transition metals in biomaterials. Here, we demonstrate a novel EPR spectrometer using a single artificial atom as a sensitive detector of spin magnetization. The artificial atom, a superconducting flux qubit, provides advantages in terms of its strong coupling with magnetic fields. We estimate a sensitivity of ~400 spins·Hz−1/2 with a magnetic sensing volume around 10−14λ3 (50 femtoliters), where λ is the wavelength of the irradiated microwave. Our artificial atom works as a highly sensitive EPR spectrometer with micron-scale area with future opportunity for measuring single spins on the nanometer scale.
- 29 March 2019
- Published by Springer Nature in Communications Physics
- Vol. 2 (1) , 1-7
Open AccessElectron paramagnetic resonance spectroscopy using a single artificial atom
Electron paramagnetic resonance (EPR) spectroscopy is an important technology in physics, chemistry, materials science, and biology. Sensitive detection with a small sample volume is a key objective in these areas, because it is crucial, for example, for the readout of a highly packed spin based quantum memory or the detection of transition metals in biomaterials. Here, we demonstrate a novel EPR spectrometer using a single artificial atom as a sensitive detector of spin magnetization. The artificial atom, a superconducting flux qubit, provides advantages in terms of its strong coupling with magnetic fields. We estimate a sensitivity of ~400 spins·Hz−1/2 with a magnetic sensing volume around 10−14λ3 (50 femtoliters), where λ is the wavelength of the irradiated microwave. Our artificial atom works as a highly sensitive EPR spectrometer with micron-scale area with future opportunity for measuring single spins on the nanometer scale.
- Open Access
Electron paramagnetic resonance spectroscopy using a single artificial atom
Electron paramagnetic resonance (EPR) spectroscopy is an important technology in physics, chemistry, materials science, and biology. Sensitive detection with a small sample volume is a key objective in these areas, because it is crucial, for example, for the readout of a highly packed spin based quantum memory or the detection of unlabeled metalloproteins in a single cell. In conventional EPR spectrometers, the energy transfer from the spins to the cavity at a Purcell enhanced rate plays an essential role and requires the spins to be resonant with the cavity, however the size of the cavity (limited by the wavelength) makes it difficult to improve the spatial resolution. Here, we demonstrate a novel EPR spectrometer using a single artificial atom as a sensitive detector of spin magnetization. The artificial atom, a superconducting flux qubit, provides advantages both in terms of its quantum properties and its much stronger coupling with magnetic fields. We have achieved a sensitivity of $\sim$400 spins/$\sqrt{\mathrm{Hz}}$ with a magnetic sensing volume around $10^{-14} \lambda^3$ (50 femto-liters). This corresponds to an improvement of two-order of magnitude in the magnetic sensing volume compared with the best cavity based spectrometers while maintaining a similar sensitivity as those spectrometers . Our artificial atom is suitable for scaling down and thus paves the way for measuring single spins on the nanometer scale.Open AccessElectron paramagnetic resonance spectroscopy using a single artificial atom
Electron paramagnetic resonance (EPR) spectroscopy is an important technology in physics, chemistry, materials science, and biology. Sensitive detection with a small sample volume is a key objective in these areas, because it is crucial, for example, for the readout of a highly packed spin based quantum memory or the detection of unlabeled metalloproteins in a single cell. In conventional EPR spectrometers, the energy transfer from the spins to the cavity at a Purcell enhanced rate plays an essential role and requires the spins to be resonant with the cavity, however the size of the cavity (limited by the wavelength) makes it difficult to improve the spatial resolution. Here, we demonstrate a novel EPR spectrometer using a single artificial atom as a sensitive detector of spin magnetization. The artificial atom, a superconducting flux qubit, provides advantages both in terms of its quantum properties and its much stronger coupling with magnetic fields. We have achieved a sensitivity of $\sim$400 spins/$\sqrt{\mathrm{Hz}}$ with a magnetic sensing volume around $10^{-14} \lambda^3$ (50 femto-liters). This corresponds to an improvement of two-order of magnitude in the magnetic sensing volume compared with the best cavity based spectrometers while maintaining a similar sensitivity as those spectrometers . Our artificial atom is suitable for scaling down and thus paves the way for measuring single spins on the nanometer scale.