Sergejs Olonkins
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sergejs Olonkins has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Vjaceslavs Bobrovs
Institute of Photonics, Electronics and Telecommunications, Riga Technical University, 1048 Riga, Latvia
7 shared publications - Jurgis Porins
Institute of Photonics, Electronics and Telecommunications, Riga Technical University, LV-1048 Riga, Latvia
4 shared publications - Girts Ivanovs
Institute of Telecommunications, Riga Technical University, Latvia
3 shared publications - Sandis Spolitis
Institute of Photonics, Electronics and Telecommunications, Riga Technical University, Riga, Latvia
3 shared publications Ilya Lyashuk
Institute of Telecommunications, Riga Technical University, Riga, Latvia
2 shared publications- Oskars Ozolins
Riga Technical University
2 shared publications
Latest Publications
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1747-1752
Suppression of CC-FWM inter-channel crosstalk using unequal channel spacing in an 8-channel WDM transmission system with parametric amplification
In this research the authors investigate the opportunities of suppression of CC-FWM produced inter channel crosstalk by introducing unequal channel spacing in an 8-channel DWM transmission system with a single-pump FOPA used for signal amplification. The frequency spacing between the neighbor channels was consistently increased from 50 GHz to 125 GHz with steps of 12.5 GHz, thus the overall frequency band used from transmission was just 0.6125 THz. In order to estimate the performance of the provided solution, the dependence of bit-error ratio (BER) values on the power of the detected signal was obtained in the channel with the highest BER. These results were compared with the corresponding results obtained the same WDM transmission system but with 100 GHz channel spacing.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1747-1752
Suppression of CC-FWM inter-channel crosstalk using unequal channel spacing in an 8-channel WDM transmission system with parametric amplification
In this research the authors investigate the opportunities of suppression of CC-FWM produced inter channel crosstalk by introducing unequal channel spacing in an 8-channel DWM transmission system with a single-pump FOPA used for signal amplification. The frequency spacing between the neighbor channels was consistently increased from 50 GHz to 125 GHz with steps of 12.5 GHz, thus the overall frequency band used from transmission was just 0.6125 THz. In order to estimate the performance of the provided solution, the dependence of bit-error ratio (BER) values on the power of the detected signal was obtained in the channel with the highest BER. These results were compared with the corresponding results obtained the same WDM transmission system but with 100 GHz channel spacing.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2450-2454
Investigation of 4-PAM modulation format for use in WDM-PON optical access systems
In this paper, we investigate the performance of four level pulse amplitude modulation (PAM-4) format in fiber optical access networks. PAM-4 modulation format has higher spectral efficiency if compared to widespread used non-return-to zero (NRZ) line code and therefore potentially can provide higher data transmission speeds in fiber optical networks with limited bandwidth. When transmission speed is increased, chromatic dispersion (CD) can be the main distance-limiting factor for PAM-4 modulation format. For this reason in this paper we investigate maximal transmission distance with dispersion compensation and without dispersion compensation in 4-PAM modulated wavelength division multiplexed passive optical network (WDM-PON), as well as minimal available channel spacing. It is shown that dispersion compensation with fiber Bragg grating dispersion compensation module (FBG DCM) can improve the performance and maximal available reach of PAM-4 modulated optical signal by 25.4% or extra 15 km in length.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2450-2454
Investigation of 4-PAM modulation format for use in WDM-PON optical access systems
In this paper, we investigate the performance of four level pulse amplitude modulation (PAM-4) format in fiber optical access networks. PAM-4 modulation format has higher spectral efficiency if compared to widespread used non-return-to zero (NRZ) line code and therefore potentially can provide higher data transmission speeds in fiber optical networks with limited bandwidth. When transmission speed is increased, chromatic dispersion (CD) can be the main distance-limiting factor for PAM-4 modulation format. For this reason in this paper we investigate maximal transmission distance with dispersion compensation and without dispersion compensation in 4-PAM modulated wavelength division multiplexed passive optical network (WDM-PON), as well as minimal available channel spacing. It is shown that dispersion compensation with fiber Bragg grating dispersion compensation module (FBG DCM) can improve the performance and maximal available reach of PAM-4 modulated optical signal by 25.4% or extra 15 km in length.
- 1 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21570221,p. 23-28
Cost effective WDM-AON with multicarrier source based on dual-pump FOPA
The aim of this paper is to demonstrate the ability of a fiber optical parametric amplifier to increase the number of carriers two times in a 32 channel wavelength-division-multiplexed active optical network. The parametric amplifier is placed at the receiver section. The 32 carriers are obtained by using 16 initial carriers, which while processing through the high non-linearity fiber, initiated the generation of 16 phase-conjugated spectral components that afterwards were used as transport for the informative signal. The provided solution has ensured even distribution of all 32 channels with channel spacing of 100 GHz with power non-uniformity just below 2dB among all 32 carriers. It is demonstrated that the provided solution with the introduced cost-effective seeded four-wave-mixing based multicarrier light source is capable to provide downstream data transmission over 20 km long standard single-mode fiber span simultaneously ensuring bit-error-ratio values below the 10-12 threshold for all of the 32 channels.
- 1 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21570221,p. 23-28
Cost effective WDM-AON with multicarrier source based on dual-pump FOPA
The aim of this paper is to demonstrate the ability of a fiber optical parametric amplifier to increase the number of carriers two times in a 32 channel wavelength-division-multiplexed active optical network. The parametric amplifier is placed at the receiver section. The 32 carriers are obtained by using 16 initial carriers, which while processing through the high non-linearity fiber, initiated the generation of 16 phase-conjugated spectral components that afterwards were used as transport for the informative signal. The provided solution has ensured even distribution of all 32 channels with channel spacing of 100 GHz with power non-uniformity just below 2dB among all 32 carriers. It is demonstrated that the provided solution with the introduced cost-effective seeded four-wave-mixing based multicarrier light source is capable to provide downstream data transmission over 20 km long standard single-mode fiber span simultaneously ensuring bit-error-ratio values below the 10-12 threshold for all of the 32 channels.
- 1 July 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 93, 955-959
Demonstration of binary PolSK to OOK modulation format conversion using a single-pump fiber optical parametric amplifier
The main goal of this paper is to investigate the ability of a single-pump fiber optical parametric amplifier with linearly polarized pumping radiation to provide binary polarization shift keying to intensity on-off keying modulation format conversion in a single channel optical transmission system. The amplifier produced up to 14.8 dB of on-off gain, and it was demonstrated that such level of amplification is sufficient to provide modulation format conversion, while maintaining acceptable quality of the converted signal. It was found that due to fiber birefringence the original state of polarization needs to be recovered at the input of the amplifier, otherwise, drop in amplification and converted signal discrepancies will occur.
- 1 July 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 93, 955-959
Demonstration of binary PolSK to OOK modulation format conversion using a single-pump fiber optical parametric amplifier
The main goal of this paper is to investigate the ability of a single-pump fiber optical parametric amplifier with linearly polarized pumping radiation to provide binary polarization shift keying to intensity on-off keying modulation format conversion in a single channel optical transmission system. The amplifier produced up to 14.8 dB of on-off gain, and it was demonstrated that such level of amplification is sufficient to provide modulation format conversion, while maintaining acceptable quality of the converted signal. It was found that due to fiber birefringence the original state of polarization needs to be recovered at the input of the amplifier, otherwise, drop in amplification and converted signal discrepancies will occur.
- 1 July 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 552-557
Realization of dense bidirectional spectrum sliced WDM-PON access system
The present paper proposes high speed dense 8-channel bidirectional WDM-PON access system where spectrally-uniform ASE source is shared among multiple users for realization of downstream transmission. Upstream transmission is realized by using conventional laser based solution. Proposed system is based on ITU-T DWDM grid and operating at 10 Gbit/s per channel symmetrically on both directions. It is demonstrated that implemented spectrum slicing technology is capable to provide downstream data transmission over 20 km SMF fiber span with BER<;10-12 by using additional fiber Bragg grating chromatic dispersion compensation module and excess intensity noise reduction by additional semiconductor optical amplifier.
- 1 July 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 552-557
Realization of dense bidirectional spectrum sliced WDM-PON access system
The present paper proposes high speed dense 8-channel bidirectional WDM-PON access system where spectrally-uniform ASE source is shared among multiple users for realization of downstream transmission. Upstream transmission is realized by using conventional laser based solution. Proposed system is based on ITU-T DWDM grid and operating at 10 Gbit/s per channel symmetrically on both directions. It is demonstrated that implemented spectrum slicing technology is capable to provide downstream data transmission over 20 km SMF fiber span with BER<;10-12 by using additional fiber Bragg grating chromatic dispersion compensation module and excess intensity noise reduction by additional semiconductor optical amplifier.
- Open Access
- 14 January 2014
- Published by Kaunas University of Technology (KTU) in Elektronika ir Elektrotechnika
- Vol. 20 (1) , 88-91
Investigation of Fiber Optical Parametric Amplifier Performance in DWDM Transmission Systems
During the last decade, due to the growing demand on high capacity transmission, the evolution of optical transmission systems is moving into the focus of dense and cost-effective solutions. This has resulted in stricter requirements for the elements used in optical transmission systems, including optical amplifiers (FOPAs). One of the innovative and most promising types of amplifiers is fiber optical parametric amplifiers. In this article the authors implement a lumped single pump FOPA in a 8 channel DWDM transmission system and investigate the performance of the FOPA in order to obtain a configuration that would ensure higher level of amplification coped with less amplifier produced signal impairments. DOI: http://dx.doi.org/10.5755/j01.eee.20.1.6170
- 14 January 2014
- Published by Kaunas University of Technology (KTU) in Elektronika ir Elektrotechnika
- Vol. 20 (1) , 88-91
Open AccessInvestigation of Fiber Optical Parametric Amplifier Performance in DWDM Transmission Systems
During the last decade, due to the growing demand on high capacity transmission, the evolution of optical transmission systems is moving into the focus of dense and cost-effective solutions. This has resulted in stricter requirements for the elements used in optical transmission systems, including optical amplifiers (FOPAs). One of the innovative and most promising types of amplifiers is fiber optical parametric amplifiers. In this article the authors implement a lumped single pump FOPA in a 8 channel DWDM transmission system and investigate the performance of the FOPA in order to obtain a configuration that would ensure higher level of amplification coped with less amplifier produced signal impairments. DOI: http://dx.doi.org/10.5755/j01.eee.20.1.6170
- 1 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 15-20
Binary PolSK to OOK modulation format conversion in single-pump FOPA for optical access networks
The interest of implementation of advanced modulation formats in metro and access networks has experienced a steady increase under the influence of exponentially increasing data amount from multimedia services like videoconferencing, high definition television, video on demand, interactive games and others. The transition period to advanced modulation formats requires a solution for efficient all-optical modulation format conversion to avoid replacement of the existing end-user hardware with the more expensive and complex devices capable of processing of advanced modulation formats. In this paper the authors have investigated the opportunity of all-optical modulation format conversion from binary polarization shift keying to intensity on-off keying in optical metro and access network using a single-pump fiber optical parametric amplifier. This preamplifier ensures up to 30 dB of gain and provides efficient modulation format conversion in the access network. Such additional functionality of single-pump parametric amplifiers in optical access networks has not been demonstrated so far.
- 1 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 15-20
Binary PolSK to OOK modulation format conversion in single-pump FOPA for optical access networks
The interest of implementation of advanced modulation formats in metro and access networks has experienced a steady increase under the influence of exponentially increasing data amount from multimedia services like videoconferencing, high definition television, video on demand, interactive games and others. The transition period to advanced modulation formats requires a solution for efficient all-optical modulation format conversion to avoid replacement of the existing end-user hardware with the more expensive and complex devices capable of processing of advanced modulation formats. In this paper the authors have investigated the opportunity of all-optical modulation format conversion from binary polarization shift keying to intensity on-off keying in optical metro and access network using a single-pump fiber optical parametric amplifier. This preamplifier ensures up to 30 dB of gain and provides efficient modulation format conversion in the access network. Such additional functionality of single-pump parametric amplifiers in optical access networks has not been demonstrated so far.
- 1 October 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21570221,p. 577-582
Hybrid optical amplifiers for flexible development in long reach optical access system
In this paper the authors have investigated the performance improvement in long reach optical access system with hybrid optical amplifiers. The apparent options of optical amplification in wavelength division multiplexing systems include the distributed Raman amplifiers, erbium doped fiber amplifiers, and semiconductor optical amplifiers. In our case distributed Raman amplifier is located at the mid-span reach extender which allows for remote amplification in passive network nodes by distributing a Raman pump together with the data signals. In the case of only distributed Raman amplifier in long reach optical access system wavelength division multiplexing exploitation is inefficient. Combining the advantages of different amplifiers allows fast gain dynamics, simultaneous large bandwidth amplification, and the ability to provide gain at any wavelength. Degradation of optical signal quality is evaluated in 10 Gbit/s long reach wavelength division multiplexing optical access system with hybrid distributed Raman-erbium doped fiber amplifier and distributed Raman-semiconductor optical amplifier.
- 1 October 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21570221,p. 577-582
Hybrid optical amplifiers for flexible development in long reach optical access system
In this paper the authors have investigated the performance improvement in long reach optical access system with hybrid optical amplifiers. The apparent options of optical amplification in wavelength division multiplexing systems include the distributed Raman amplifiers, erbium doped fiber amplifiers, and semiconductor optical amplifiers. In our case distributed Raman amplifier is located at the mid-span reach extender which allows for remote amplification in passive network nodes by distributing a Raman pump together with the data signals. In the case of only distributed Raman amplifier in long reach optical access system wavelength division multiplexing exploitation is inefficient. Combining the advantages of different amplifiers allows fast gain dynamics, simultaneous large bandwidth amplification, and the ability to provide gain at any wavelength. Degradation of optical signal quality is evaluated in 10 Gbit/s long reach wavelength division multiplexing optical access system with hybrid distributed Raman-erbium doped fiber amplifier and distributed Raman-semiconductor optical amplifier.
- 7 September 2012
- Published by Kaunas University of Technology (KTU) in Elektronika ir Elektrotechnika
- Vol. 123 (7) , 133-136
Comparison of Semiconductor Optical Amplifier and Discrete Raman Amplifier Performance in DWDM Systems
In the last decade due to the growing demand on high capacity transmission, DWDM transmission systems have evolved rapidly. The growth of transmission speed and the decrease in channel spacing has resulted in stricter requirements to the elements used in optical signal transmission process, including optical amplifiers. In this article we take one of the most popular DWDM solutions – a 10 Gbit/s 16 channel NRZ-OOK 50 GHz DWDM transmission system, and implement a SOA and a RA as a single in-line amplifier, in order to estimate and compare their performance, and to identify and estimate the main factors that limit the total transmission quality in both cases. Ill. 6, bibl. 6, tabl. 1 (in English; abstracts in English and Lithuanian).DOI: http://dx.doi.org/10.5755/j01.eee.123.7.2392
- 7 September 2012
- Published by Kaunas University of Technology (KTU) in Elektronika ir Elektrotechnika
- Vol. 123 (7) , 133-136
Comparison of Semiconductor Optical Amplifier and Discrete Raman Amplifier Performance in DWDM Systems
In the last decade due to the growing demand on high capacity transmission, DWDM transmission systems have evolved rapidly. The growth of transmission speed and the decrease in channel spacing has resulted in stricter requirements to the elements used in optical signal transmission process, including optical amplifiers. In this article we take one of the most popular DWDM solutions – a 10 Gbit/s 16 channel NRZ-OOK 50 GHz DWDM transmission system, and implement a SOA and a RA as a single in-line amplifier, in order to estimate and compare their performance, and to identify and estimate the main factors that limit the total transmission quality in both cases. Ill. 6, bibl. 6, tabl. 1 (in English; abstracts in English and Lithuanian).DOI: http://dx.doi.org/10.5755/j01.eee.123.7.2392