Seryeyohan Cho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Seryeyohan Cho has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Tae Jun Yu
Handong Global Univ, Dept Adv Convergence, Pohang 37554, South Korea
8 shared publications - Seungjin Hwang
HIL Lab. Inc
7 shared publications - Jihoon Jeong
Korea Institute of Industrial Technology
6 shared publications - Daewoong Park
Department of Advanced Convergence, Handong Global University 1 , Pohang 37554, Republic of Korea
3 shared publications - Geonhui Lee
HIL Lab. Inc
2 shared publications - Hanjin Jo
Handong Global Univ, Dept Adv Convergence, Pohang 37554, South Korea
2 shared publications
Latest Publications
- Open Access
- 1 June 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (6) , 065130
Surface wettability control on zircaloy-4 by nanosecond Nd:YAG laser with beam homogenizer
We introduce the laser-induced surface processing (LISP) method that imparts hydrophilicity and hydrophobicity using a Nd:YAG nanosecond laser, especially the high-fluence (HF) condition for fast processing and the low-fluence (LF) condition to control the surface wettability. A prime example of HF processing is laser shock peening, where we show the potential to achieve both strength enhancement and wettability in materials. This could be a new advantageous feature in areas such as reactor maintenance. We combined a beam homogenizer with LISP to increase processing efficiency. The beam homogenizer realizes a uniform fluorescence distribution in the beam area and, at the same time, makes the beam rectangular to increase work efficiency. The maximum contact angle was 123.8° for the zircaloy-4 specimen through HF processing with the beam homogenizer. We also showed that nanosecond laser-induced periodic surface structures could be generated by combining LF processing with specific conditions of a beam homogenizer. This could produce a superhydrophobic surface with contact angles up to 166° on zircaloy-4 or achieve a near superhydrophilic surface with a contact angle of 17.9° depending on the processing conditions.
- 1 June 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (6) , 065130
Open AccessSurface wettability control on zircaloy-4 by nanosecond Nd:YAG laser with beam homogenizer
We introduce the laser-induced surface processing (LISP) method that imparts hydrophilicity and hydrophobicity using a Nd:YAG nanosecond laser, especially the high-fluence (HF) condition for fast processing and the low-fluence (LF) condition to control the surface wettability. A prime example of HF processing is laser shock peening, where we show the potential to achieve both strength enhancement and wettability in materials. This could be a new advantageous feature in areas such as reactor maintenance. We combined a beam homogenizer with LISP to increase processing efficiency. The beam homogenizer realizes a uniform fluorescence distribution in the beam area and, at the same time, makes the beam rectangular to increase work efficiency. The maximum contact angle was 123.8° for the zircaloy-4 specimen through HF processing with the beam homogenizer. We also showed that nanosecond laser-induced periodic surface structures could be generated by combining LF processing with specific conditions of a beam homogenizer. This could produce a superhydrophobic surface with contact angles up to 166° on zircaloy-4 or achieve a near superhydrophilic surface with a contact angle of 17.9° depending on the processing conditions.
- Open Access
- 30 April 2022
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 40 (2) , 156-164
Study of the Change in Surface Wettability for Zircaloy-4 Utilizing Spatially Homogenized Nanosecond Laser Beam
This study introduces laser surface modification technology using a 532 nm Nd:YAG nanosecond laser. A laser beam homogenizer was used to spatially homogenize the laser beam into a square shape with an interference pattern of 30 μm. For laser surface modification processing, primary processing under 110 conditions was first performed, and then, 15 types of main processing conditions were determined based on the three-dimensional surface structure of laser surface modified zircaloy-4. Subsequently, the specimen was post-processed using three methods: left in the air (25 ℃), heated in the oven (200 ℃ for 2 h), and boiled in water (100 ℃ for 2 h). In the absence of post-processing or with heat post-processing, the laser surface modified zircaloy-4 showed super hydrophobicity with a contact angle of 150° or higher for specific laser surface processing parameters. Under specific laser surface processing conditions, the laser surface modified zircaloy-4 with boiling water post-processing exhibited properties close to super hydrophilic with a contact angle of less than 5°. It was confirmed that the surface wettability of zircaloy-4 can be controlled using a spatially shaped nanosecond laser beam.
- 30 April 2022
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 40 (2) , 156-164
Open AccessStudy of the Change in Surface Wettability for Zircaloy-4 Utilizing Spatially Homogenized Nanosecond Laser Beam
This study introduces laser surface modification technology using a 532 nm Nd:YAG nanosecond laser. A laser beam homogenizer was used to spatially homogenize the laser beam into a square shape with an interference pattern of 30 μm. For laser surface modification processing, primary processing under 110 conditions was first performed, and then, 15 types of main processing conditions were determined based on the three-dimensional surface structure of laser surface modified zircaloy-4. Subsequently, the specimen was post-processed using three methods: left in the air (25 ℃), heated in the oven (200 ℃ for 2 h), and boiled in water (100 ℃ for 2 h). In the absence of post-processing or with heat post-processing, the laser surface modified zircaloy-4 showed super hydrophobicity with a contact angle of 150° or higher for specific laser surface processing parameters. Under specific laser surface processing conditions, the laser surface modified zircaloy-4 with boiling water post-processing exhibited properties close to super hydrophilic with a contact angle of less than 5°. It was confirmed that the surface wettability of zircaloy-4 can be controlled using a spatially shaped nanosecond laser beam.
- Open Access
Performance Evaluation of Solid-State Laser Gain Module by Measurement of Thermal Effect and Energy Storage
The optimization of solid-state laser cavities requires a deep understanding of the gain module, the most critical laser component. This study proposes a procedure for evaluating the performance of the solid-state laser gain module. The thermal effect and energy storage characteristics are the performance criteria. A normalized heating parameter was calculated as a quantitative indicator of the performance criteria. We proposed a method to quantify the heat dissipated into the gain medium using the wavefront distortion, thermal deformation theory of the gain medium, and the ray transfer matrix method. The suggested procedure was verified by evaluating the flashlamp type Nd:YAG rod gain module, but it can also even be extended to other solid-state laser gain modules by applying the appropriate thermal deformation theory.
Open AccessPerformance Evaluation of Solid-State Laser Gain Module by Measurement of Thermal Effect and Energy Storage
The optimization of solid-state laser cavities requires a deep understanding of the gain module, the most critical laser component. This study proposes a procedure for evaluating the performance of the solid-state laser gain module. The thermal effect and energy storage characteristics are the performance criteria. A normalized heating parameter was calculated as a quantitative indicator of the performance criteria. We proposed a method to quantify the heat dissipated into the gain medium using the wavefront distortion, thermal deformation theory of the gain medium, and the ray transfer matrix method. The suggested procedure was verified by evaluating the flashlamp type Nd:YAG rod gain module, but it can also even be extended to other solid-state laser gain modules by applying the appropriate thermal deformation theory.
- Open Access
- 23 November 2020
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 37 (12) , 3874-3881
Numerical analysis of beam distortion induced by thermal effects in chirped volume Bragg grating compressors for high-power lasers
We conducted a study on the thermal effects in chirped volume Bragg gratings (CVBGs) used as optical compressors in high-power lasers. A simulation code was developed to predict the distortion of the pulses by the thermal effects. The types and significance of the thermal distortion were analyzed using an Yb:YAG laser with an average power of 250 W. The temperature distribution in the CVBG, the thermal lens effect, the beam propagation path changes due to the thermal lens, and the compression efficiency decrease due to the phase delay were analyzed. As a result, we predict that the peak power decreases to 63.9% due to the thermal effects under the operating conditions of 250 W. We also suggest new designs for the CVBG mount that minimize the peak power loss. We expect the peak power loss to be reduced only by 1.1% when using our new mount design for the CVBG.
- 23 November 2020
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 37 (12) , 3874-3881
Open AccessNumerical analysis of beam distortion induced by thermal effects in chirped volume Bragg grating compressors for high-power lasers
We conducted a study on the thermal effects in chirped volume Bragg gratings (CVBGs) used as optical compressors in high-power lasers. A simulation code was developed to predict the distortion of the pulses by the thermal effects. The types and significance of the thermal distortion were analyzed using an Yb:YAG laser with an average power of 250 W. The temperature distribution in the CVBG, the thermal lens effect, the beam propagation path changes due to the thermal lens, and the compression efficiency decrease due to the phase delay were analyzed. As a result, we predict that the peak power decreases to 63.9% due to the thermal effects under the operating conditions of 250 W. We also suggest new designs for the CVBG mount that minimize the peak power loss. We expect the peak power loss to be reduced only by 1.1% when using our new mount design for the CVBG.
- Open Access
- 12 June 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (12) , 2396
Modeling and Analysis of High-Power Ti:sapphire Laser Amplifiers–A Review
We have introduced several factors that can be useful for the modeling and analysis of high-power Ti:sapphire laser amplifiers. The amplification model includes the phase distortion effect caused by the atomic phase shift (APS) in gain medium and the thermal-induced phase distortion effect caused by the high-average-power amplification. We have provided an accurate amplification model for the development of ultra-high-intensity and high-average-power lasers.
- 12 June 2019
- Published by MDPI AG in Applied Sciences
- Vol. 9 (12) , 2396
Open AccessModeling and Analysis of High-Power Ti:sapphire Laser Amplifiers–A Review
We have introduced several factors that can be useful for the modeling and analysis of high-power Ti:sapphire laser amplifiers. The amplification model includes the phase distortion effect caused by the atomic phase shift (APS) in gain medium and the thermal-induced phase distortion effect caused by the high-average-power amplification. We have provided an accurate amplification model for the development of ultra-high-intensity and high-average-power lasers.
- 8 January 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58 (2) , 020901
Amplified spontaneous emission suppression of a saturable absorber in a nanosecond double-pass laser amplifier
We propose the insertion of a saturable absorber (SA) in a nanosecond double-pass laser amplifier as an amplified spontaneous emission (ASE) suppressor. To analyze the influence of the SA, a theoretical model is developed. One-dimensional simulation results show reasonable agreement with measurements in terms of the output energy and temporal pulse shape. For our amplifier parameters, when an SA of initial transmission 0.5 is inserted, the simulation anticipates the ASE to be reduced by a factor of 0.37 while the output pulse energy is maintained.
- 8 January 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58 (2) , 020901
Amplified spontaneous emission suppression of a saturable absorber in a nanosecond double-pass laser amplifier
We propose the insertion of a saturable absorber (SA) in a nanosecond double-pass laser amplifier as an amplified spontaneous emission (ASE) suppressor. To analyze the influence of the SA, a theoretical model is developed. One-dimensional simulation results show reasonable agreement with measurements in terms of the output energy and temporal pulse shape. For our amplifier parameters, when an SA of initial transmission 0.5 is inserted, the simulation anticipates the ASE to be reduced by a factor of 0.37 while the output pulse energy is maintained.
- Open Access
- 23 August 2018
- Published by IOP Publishing in Applied Physics Express
- Vol. 11 (9) , 092701
Thermal lens effect model of Ti:sapphire for use in high-power laser amplifiers
- 23 August 2018
- Published by IOP Publishing in Applied Physics Express
- Vol. 11 (9) , 092701
Open AccessThermal lens effect model of Ti:sapphire for use in high-power laser amplifiers
- Open Access
- 30 July 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (16) , 20850
Jones calculus modeling and analysis of the thermal distortion in a Ti:sapphire laser amplifier: erratum
Equations 41–44 in our paper [ Opt. Express 26, 14362 (2016)] contain errors. We correct the equations in this erratum.
- 30 July 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (16) , 20850
Open AccessJones calculus modeling and analysis of the thermal distortion in a Ti:sapphire laser amplifier: erratum
Equations 41–44 in our paper [ Opt. Express 26, 14362 (2016)] contain errors. We correct the equations in this erratum.
- 25 July 2017
- Published by Korean Physical Society in Journal of the Korean Physical Society
- Vol. 71 (10) , 679-683
Arch-Shaped triboelectric nanogenerator as a facile device for water-wave vibrational energy
We have derived modified Frantz-Nodvik equations that simultaneously account for atomic phase shift (APS) and gain depletion as the chirped laser pulse passes through a gain medium, and have analyzed the effect of temporal pulse distortion in a Ti:sapphire multipass amplifier chain. The combination of APS and gain depletion distorted a temporal pulse and decreased the peak power. The pulse width increased from 21.3 fs to 22.8 fs and the peak power reduced to 89% for the PW class Ti:sapphire CPA laser system in the particular conditions.
- 25 July 2017
- Published by Korean Physical Society in Journal of the Korean Physical Society
- Vol. 71 (10) , 679-683
Arch-Shaped triboelectric nanogenerator as a facile device for water-wave vibrational energy
We have derived modified Frantz-Nodvik equations that simultaneously account for atomic phase shift (APS) and gain depletion as the chirped laser pulse passes through a gain medium, and have analyzed the effect of temporal pulse distortion in a Ti:sapphire multipass amplifier chain. The combination of APS and gain depletion distorted a temporal pulse and decreased the peak power. The pulse width increased from 21.3 fs to 22.8 fs and the peak power reduced to 89% for the PW class Ti:sapphire CPA laser system in the particular conditions.