Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Takaya Sato has a total of 82 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Development of Low-Friction Ion Gels for Industrial Applications

    by Toshio Kamijo, Hiroyuki Arafune, Takashi Morinaga, Takaya Sato

    Friction reduction is imperative for improving the service life and energy efficiency of mechanical systems. Ion gels using ionic liquids (ILs) as swelling agents are expected to be stable gel lubricants owing to the high thermal stability and negligible volatility of ILs; they can maintain their swollen state even under harsh conditions. Therefore, we investigated two types of ion gels: an IL-substituted double-network gel (DN ion S-gel), in which the water in the DN hydrogel is replaced by the IL 3-ethyl-1-methyl-imidazolium ethylsulfate; and a DN ion gel containing N,N-diethyl-N-(2-methoxyethyl)-N-methyl-ammonium bis(trifluoromethylsulfonyl)imide (DEME-TFSI), where one of the polymer backbones is a network of poly(N,N-diethyl-N-(2-methacryloylethyl)-N-methylammonium bis(trifluoromethylsulfonyl)imide), an IL-type polymer based on our previous synthetic study of IL polymer technology. The DN ion S-gel and DN ion gel achieved compression strengths of 25 and 30 MPa, respectively, and were thermally stable until 196°C and 335°C (10% weight-loss temperature), respectively. The coefficient of friction remained stable and low (0.02) after repeated measurements under harsh conditions (high temperature or vacuum conditions), affirming the durability of the DN ion gel.

  • Open Access

    Novel Dry Spinning Process of Natural Macromolecules for Sustainable Fiber Material -1- Proof of the Concept Using Silk Fibroin

    by Ryo Satoh, Takashi Morinaga, Takaya Sato

    Researchers around the world are developing technologies to minimize carbon dioxide emissions or carbon neutrality in various fields. In this study, the dry spinning of regenerated silk fibroin (RSF) was achieved as a proof of concept for a process using ionic liquids as dissolution aids and plasticizers in developing natural polymeric materials. A dry spinning equipment system combining a stainless-steel syringe and a brushless motor was built to generate fiber compacts from a dope of silk fibroin obtained by degumming silkworm silk cocoons and ionic liquid 1-hexyl-3-methyl-imidazolium chloride ([HMIM][Cl]) according to a general method. The maximum stress and maximum elongation of the RSF fibers were 159.9 MPa and 31.5%, respectively. RSF fibers containing ionic liquids have a homogeneous internal structure according to morphological investigations. Elemental analysis of fiber cross sections revealed the homogeneous distribution of nonvolatile ionic liquid [HMIM][Cl] in RSF fibers. Furthermore, the removal of ionic liquids from RSF fibers through impregnation washing with organic solvents was verified to enhance industrial applications. Tensile testing showed that the fiber strength could be maintained even after removing the ionic liquid. Thermogravimetric analysis results show that the organic solvent 1,1,1,3,3,3-hexafluoro-2-propanol is chemically coordinated to silk fibroin and, as a natural polymer, can withstand heat up to 250 °C.


  • Open Access

    Mechanical and Lubrication Properties of Double Network Ion Gels Obtained by a One-Step Process

    by Hiroyuki Arafune, Yuma Watarai, Toshio Kamijo, Saika Honma, Takaya Sato

    Human joints support us to reduce the impact on our body and move them smoothly. As they are composed of gel-like structures, gel materials with soft and resilient properties are expected, as lubricants, to provide high efficiency and a long lifetime for mechanical parts. While double network gels including ionic liquids as swelling agents possess high mechanical strength and stable low friction under high temperature or vacuum, their fabrication process is complex and time-consuming. In this study, we applied one-pot synthesis to a double network ion gel (DNIG) to obtain a thin gel film by a simple coating method and examined its thermal, mechanical and tribological properties. The DNIG was obtained by one-pot synthesis (DNIG-1) combining polycondensation of tetraethoxysilane and radical polymerization of methyl methacrylate to form silica and poly(methyl methacrylate) as a 1st and 2nd network, respectively. Such obtained DNIG-1 was characterized and compared with DNIG obtained by a conventional two-step process (DNIG-2). Thermogravimetric analysis and the compressive stress–strain test showed high thermal stability and mechanical strength of DNIG-1. As friction at the glass/DNIG-1 interface showed high friction compared with that at glass/DNIG-2, various counterface materials were applied to examine their effect on the friction of DNIG-1. As SUS304/DNIG-1 showed much lower friction compared with glass/DNIG-1, the difference in the friction was presumably due to the different adsorption forces and compatibility between the materials.


  • Novel Use of a Pyridinium Salt to Form a Solid Electrolyte Interphase (SEI) on High Voltage Lithium-Excess Layered Positive Active Material

    by Ryo Shomura, Keita Sakakibara, Shoko Marukane, Kimiyo Nakamichi, Takashi Morinaga, Yoshinobu Tsujii, Takaya Sato

    Lithium-excess layered positive electrodes containing Fe and Ni are promising materials for the next generation of high voltage lithium ion batteries (LIB) because they are more chemically stable than those using Co and use more widely available metals. However, a positive electrode driven with a high voltage generates an electrochemical decomposition reaction of the electrolyte at the electrode interface and a significant deterioration in performance occurs. In order to suppress electrolysis of the electrolyte solution, a promising solution is to form a solid electrolyte interphase (SEI) on the electrode to mediate contact between the electrolyte solution and the electrode. In this study, we discovered that a pyridinium series salt, an ionic liquid, used as an additive, forms a good SEI on the positive electrode surface to improve the overall performance of the LIBs, such as improved cycle capacity and inhibited gas generation. Furthermore, from XPS, TOF-SIMS, 1H-NMR and SEM measurements, we discuss the chemical makeup of the SEI and its formation mechanism, and propose a powerful method to achieve the next generation of high energy-density lithium ion batteries.


  • Open Access

    In Situ Surface-Initiated Atom-Transfer Radical Polymerization Utilizing the Nonvolatile Nature of Ionic Liquids: A First Attempt

    by Ryo Satoh, Saika Honma, Hiroyuki Arafune, Ryo Shomura, Toshio Kamijo, Takashi Morinaga, Takaya Sato

    In this paper, in situ surface-initiated atom-transfer radical polymerization (SI-ATRP) based on both an open and a coated system, without using volatile reagents, was developed to overcome the limited usage of ATRP due to the necessity of sealing. Nonvolatile ionic liquid (IL)-type components were used, specifically N,N-diethyl-N-(2-methacryloylethyl)-N-methylammonium bis(trifluoromethylsulfonyl)imide as the polymerizable monomer and N,N-diethylmethyl(2-methoxyethyl)ammonium bis(trifluoromethylsulfonyl)imide as the polymerization solvent. In the experiment, the reversible-deactivation radical polymerization characteristics are properly ensured in nonvolatile ATRP solution coated on silicon wafer as thin liquid film, to form concentrated polymer brushes (CPBs). The average molecular weight and molecular-weight distribution of the polymer produced in the liquid film and formed on silicon wafer were measured by gel permeation chromatography, which confirms that the polymerization reaction occurred as designed. Furthermore, it is clarified that the surface of the polymer brush synthesized in situ swollen by IL also exhibited low friction characteristics, comparable to that synthesized in a typical immersion process. This paper is the first to establish the effectiveness of in situ preparation for CPBs by using the coating technique.


  • Open Access

    Adsorption and Release of Rose Bengal on Layer-by-Layer Films of Poly(Vinyl Alcohol) and Poly(Amidoamine) Dendrimers Bearing 4-Carboxyphenylboronic Acid

    by Kentaro Yoshida, Akane Yamaguchi, Hiroki Midorikawa, Toshio Kamijo, Tetsuya Ono, Takenori Dairaku, Takaya Sato, Tsutomu Fujimura, Yoshitomo Kashiwagi, Katsuhiko Sato

    Phenylboronic acid-bearing polyamidoamine dendrimer (PBA-PAMAM)/poly(vinyl alcohol) (PVA) multilayer films were prepared through the layer-by-layer (LbL) deposition of PBA-PAMAM solution and PVA solution. PBA-PAMAM/PVA films were constructed successfully through the formation of boronate ester bonds between the boronic acid moiety in PBA and 1,3-diol units in PVA. When the (PBA-PAMAM/PVA)5 films were immersed in rose bengal (RB) solution, RB was adsorbed onto the LbL films. The amount of RB adsorbed was higher in the LbL films immersed in acidic solution than in basic solution. The release of RB from the LbL films was also promoted in the basic solution, while it was suppressed in the acidic solution. The boronic acid ester is oxidized to phenol by hydrogen peroxide (H2O2) and the carbon-boron bond is cleaved, so that the (PBA-PAMAM/PVA)5 films can be decomposed by immersion in H2O2 solution. Therefore, when RB-adsorbed (PBA-PAMAM/PVA)5 films were immersed in H2O2 solution, the release of RB was moderately promoted when the solution was weakly acidic.


  • Open Access

    Decomposition of Glucose-Sensitive Layer-by-Layer Films Using Hemin, DNA, and Glucose Oxidase

    by Kentaro Yoshida, Yu Kashimura, Toshio Kamijo, Tetsuya Ono, Takenori Dairaku, Takaya Sato, Yoshitomo Kashiwagi, Katsuhiko Sato

    Glucose-sensitive films were prepared through the layer-by-layer (LbL) deposition of hemin-modified poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA + GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA + GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve more reactive oxygen species (ROS) that were formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. In addition, GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the (H-PEI/DNA + GOx)5 film was observed when the thin film was immersed in a glucose solution. (H-PEI/DNA + GOx)5 films exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated that the decomposition of the film increased with the time to 9.97%, 16.3%, 23.1%, and 30.5%, respectively. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strengths close to physiological conditions, it was possible to slowly decompose the LbL film at low glucose concentrations of 1–10 mM.


  • Open Access

    Decomposition of Glucose-Sensitive Layer-by-Layer Films Using Hemin, DNA, and Glucose Oxidase

    by Kentaro Yoshida, Yu Kashimura, Toshio Kamijo, Tetsuya Ono, Takenori Dairaku, Takaya Sato, Yoshitomo Kashiwagi, Katsuhiko Sato

    Glucose-sensitive films were prepared by the layer-by-layer (LbL) deposition of poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA+GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA+GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve a more reactive oxygen species (ROS) that was formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the H-PEI/DNA+GOx)5 film was observed when the thin film was immersed in a glucose solution. A (H-PEI/DNA+GOx)5 film exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated decomposition of the film increased with the time. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strength close to physiological conditions, it was possible to slowly decompose the LbL film at a sub-millimolar glucose concentration.

  • Open Access

    Concentrated Polymer Brush as Reciprocating Seal Material for Low Leakage and Low Friction

    by Chiharu Tadokoro, Kosuke Sato, Takuo Nagamine, Ken Nakano, Shinya Sasaki, Takaya Sato, Keita Sakakibara, Yoshinobu Tsujii

    Recently, concentrated polymer brushes (CPBs) have attracted much attention as potential tribomaterials showing an ultralow friction coefficient (e.g., 10−4 in a microtribological analysis). In this study, a homemade apparatus modeling reciprocating seals was developed, which consisted of an inner steel rod and an outer steel ring with a narrow clearance less than several tens of micrometers. A few-micrometer-thick CPB film of poly(methyl methacrylate) well-swollen with an ionic liquid was prepared on each steel surface, and the impact of applying the CPB film to the clearance of reciprocating seals was examined by measuring the leakage rate of a fluid and the friction coefficient in reciprocating motion. The results showed that the CPB film narrowed the clearance between the two steel surfaces, which improved its sealing performance. In addition, the CPB film yielded a quite low friction coefficient (e.g., 10−3), which assured its smooth motion with small energy loss.