I. Ethem Karadirek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
I. Ethem Karadirek has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Habib Muhammetoglu
Environmental Engineering Department, Engineering Faculty, Akdeniz University, Antalya 07070, Türkiye
5 shared publications Asli Nur Rizvanoglu
4 shared publications- Ayse Muhammetoglu
Environmental Engineering Department, Engineering Faculty, Akdeniz University, Antalya 07070, Türkiye
4 shared publications Habib Muhammetoglu
Department of Environmental Engineering, Akdeniz University, Antalya, Turkey
4 shared publicationsTugba Akdeniz
4 shared publicationsAyse Muhammetoglu
3 shared publications
Latest Publications
- Open Access
- 13 June 2026
- Published by Springer Nature in Water Resources Management
- Vol. 40 (9)
Implementing Machine Learning Algorithms for Pipe Failure Analysis in Water Distribution Systems
Pipe failures in water distribution systems occur due to various physical and environmental factors, and their analysis is essential for improving water loss control and asset management strategies. This study provides an innovative application of machine learning techniques to analyze pipe failures in a pilot study area (PSA) in Antalya, Türkiye, where failure data were recorded over a seven-year period. The factors considered in this study include pipe material, age, diameter, and length. Eight machine learning techniques, including Naïve Bayes, artificial neural networks, logistic regression, XGBoost, LightGBM, CatBoost, random forest, and support vector classification, were applied for pipe failure analysis. According to the findings, XGBoost achieved the highest prediction accuracy with an Area Under Curve (AUC) value of 0.99. The results further identified pipe length as the most influential factor in pipe failures, while PVC pipes were found to be the most prone to failure in the PSA. This comprehensive analysis not only provides valuable insights into pipe failure analysis but also offers an effective tool for optimal management of water distribution systems. Future studies should incorporate additional factors, such as the number of service connections and traffic load, to enhance failure probability assessments and inform optimal pipe replacement strategies.
- 13 June 2026
- Published by Springer Nature in Water Resources Management
- Vol. 40 (9)
Open AccessImplementing Machine Learning Algorithms for Pipe Failure Analysis in Water Distribution Systems
Pipe failures in water distribution systems occur due to various physical and environmental factors, and their analysis is essential for improving water loss control and asset management strategies. This study provides an innovative application of machine learning techniques to analyze pipe failures in a pilot study area (PSA) in Antalya, Türkiye, where failure data were recorded over a seven-year period. The factors considered in this study include pipe material, age, diameter, and length. Eight machine learning techniques, including Naïve Bayes, artificial neural networks, logistic regression, XGBoost, LightGBM, CatBoost, random forest, and support vector classification, were applied for pipe failure analysis. According to the findings, XGBoost achieved the highest prediction accuracy with an Area Under Curve (AUC) value of 0.99. The results further identified pipe length as the most influential factor in pipe failures, while PVC pipes were found to be the most prone to failure in the PSA. This comprehensive analysis not only provides valuable insights into pipe failure analysis but also offers an effective tool for optimal management of water distribution systems. Future studies should incorporate additional factors, such as the number of service connections and traffic load, to enhance failure probability assessments and inform optimal pipe replacement strategies.
- 6 February 2026
- Published by Taylor & Francis in Urban Water Journal
- Vol. 23 (6) , 1033-1042
Pressure-influenced metering accuracy in water distribution systems: experimental assessment of multi-jet, volumetric, and ultrasonic water meters
- 6 February 2026
- Published by Taylor & Francis in Urban Water Journal
- Vol. 23 (6) , 1033-1042
Pressure-influenced metering accuracy in water distribution systems: experimental assessment of multi-jet, volumetric, and ultrasonic water meters
- Open Access
- 28 February 2025
- Published by Springer Nature in International Journal of Environmental Science and Technology
- p. 1-19
Feasibility of Fenton-based oxidation for reducing organic content, toxicity, and carbon footprint of automotive industry wastewater
Automotive industry wastewater, particularly from the cataphoresis process, presents a challenge due to its high chemical oxygen demand and heavy metal content. Biological treatment alone is often insufficient, requiring pretreatment to enhance biodegradability. Fenton oxidation effectively targets toxic compounds, reducing inhibition of biological process. This study evaluates the feasibility of Fenton, Fenton-based, and photo-Fenton oxidation for pretreating automotive industry wastewater, aiming to optimize chemical oxygen demand removal and minimize sludge formation. Experimental studies using Response Surface Methodology revealed that Fenton and Fenton-based oxidations achieved similar chemical oxygen demand removal efficiencies, although the Fenton-based process with ferric iron produced more sludge. Photo-Fenton oxidation did not provide any significant benefit. Inhibition tests showed Fenton pretreatment reduced sludge inhibition from 44 to as low as 9% under optimal conditions. The optimal operating conditions for classical Fenton oxidation were determined as a ferrous iron concentration of 0.58 g L−1, a hydrogen peroxide to chemical oxygen demand molar ratio of 0.58 mol mol−1, and a reaction time of 30 min, resulting in a 49.58% chemical oxygen demand removal with minimal sludge formation and activated sludge inhibition. Compared to the coagulation-flocculation process, Fenton oxidation demonstrated the potential to reduce the carbon footprint by 6.6–16.6%, based on carbon dioxide emissions from chemical consumption. Therefore, classical Fenton oxidation as a pretreatment process can enhance biological treatment efficiency and lower the carbon footprint of automotive industry wastewater treatment. Graphical abstract
- 28 February 2025
- Published by Springer Nature in International Journal of Environmental Science and Technology
- p. 1-19
Open AccessFeasibility of Fenton-based oxidation for reducing organic content, toxicity, and carbon footprint of automotive industry wastewater
Automotive industry wastewater, particularly from the cataphoresis process, presents a challenge due to its high chemical oxygen demand and heavy metal content. Biological treatment alone is often insufficient, requiring pretreatment to enhance biodegradability. Fenton oxidation effectively targets toxic compounds, reducing inhibition of biological process. This study evaluates the feasibility of Fenton, Fenton-based, and photo-Fenton oxidation for pretreating automotive industry wastewater, aiming to optimize chemical oxygen demand removal and minimize sludge formation. Experimental studies using Response Surface Methodology revealed that Fenton and Fenton-based oxidations achieved similar chemical oxygen demand removal efficiencies, although the Fenton-based process with ferric iron produced more sludge. Photo-Fenton oxidation did not provide any significant benefit. Inhibition tests showed Fenton pretreatment reduced sludge inhibition from 44 to as low as 9% under optimal conditions. The optimal operating conditions for classical Fenton oxidation were determined as a ferrous iron concentration of 0.58 g L−1, a hydrogen peroxide to chemical oxygen demand molar ratio of 0.58 mol mol−1, and a reaction time of 30 min, resulting in a 49.58% chemical oxygen demand removal with minimal sludge formation and activated sludge inhibition. Compared to the coagulation-flocculation process, Fenton oxidation demonstrated the potential to reduce the carbon footprint by 6.6–16.6%, based on carbon dioxide emissions from chemical consumption. Therefore, classical Fenton oxidation as a pretreatment process can enhance biological treatment efficiency and lower the carbon footprint of automotive industry wastewater treatment. Graphical abstract
- 16 November 2024
- Published by Springer Nature
- p. 217-226
A Case Study on Controlling Real Losses in Large-Scale Water Distribution Systems
- 16 November 2024
- Published by Springer Nature
- p. 217-226
A Case Study on Controlling Real Losses in Large-Scale Water Distribution Systems
- Open Access
- 8 August 2024
- Published by Wiley in Water Environment Research
- Vol. 96 (8) , e11094
Fate and transport of chlorine dioxide: Modeling chlorine dioxide in water distribution systems
This study aims to conduct a comprehensive analysis of switching disinfectants from sodium hypochlorite bleach to chlorine dioxide (ClO2) in the water distribution system of Geyikbayiri, Antalya. For this purpose, bulk decay rates of ClO2 at various water temperatures were determined in laboratory studies. The study revealed ClO2 bulk decay rates of 0.12639 day−1, 0.17848 day−1, and 0.19621 day−1 at temperatures 15°C, 20°C, and 30°C, respectively. The EPANET, a widely employed computer program for simulating the extended‐period behavior of hydraulic and water quality in pressurized pipes, was utilized for the analysis of the fate and transport of ClO2. A hydraulic model was first developed, calibrated, and verified using distinct data sets. The Hazen‐Williams friction coefficient of the PSA was determined to be 120 by the trial‐and‐error method with a mean absolute error (MAE) of 0.408 m. A ClO2 model was then integrated with the calibrated and verified hydraulic model, revealing a wall decay rate of 0.01 m/day and an average MAE of 0.034 mg/l. After calibration and verification of the ClO2 model, several management scenarios were developed, and ClO2 dosing rates were determined. The study showed that ClO2 dosing rates of 0.40 mg/l and 0.45 mg/l should be applied to keep ClO2 concentrations within certain limits.Practitioner Points: Disinfectants must maintain a sufficient residual in water distribution systems. Chlorine dioxide requires less contact time and is not affected by pH fluctuations. Modeling serves as a decision‐making tool for the management of disinfectants. Bulk and wall decay rates of chlorine dioxide are crucial for management strategies. Chlorine dioxide is a good alternative as a disinfectant in such systems.
- 8 August 2024
- Published by Wiley in Water Environment Research
- Vol. 96 (8) , e11094
Open AccessFate and transport of chlorine dioxide: Modeling chlorine dioxide in water distribution systems
This study aims to conduct a comprehensive analysis of switching disinfectants from sodium hypochlorite bleach to chlorine dioxide (ClO2) in the water distribution system of Geyikbayiri, Antalya. For this purpose, bulk decay rates of ClO2 at various water temperatures were determined in laboratory studies. The study revealed ClO2 bulk decay rates of 0.12639 day−1, 0.17848 day−1, and 0.19621 day−1 at temperatures 15°C, 20°C, and 30°C, respectively. The EPANET, a widely employed computer program for simulating the extended‐period behavior of hydraulic and water quality in pressurized pipes, was utilized for the analysis of the fate and transport of ClO2. A hydraulic model was first developed, calibrated, and verified using distinct data sets. The Hazen‐Williams friction coefficient of the PSA was determined to be 120 by the trial‐and‐error method with a mean absolute error (MAE) of 0.408 m. A ClO2 model was then integrated with the calibrated and verified hydraulic model, revealing a wall decay rate of 0.01 m/day and an average MAE of 0.034 mg/l. After calibration and verification of the ClO2 model, several management scenarios were developed, and ClO2 dosing rates were determined. The study showed that ClO2 dosing rates of 0.40 mg/l and 0.45 mg/l should be applied to keep ClO2 concentrations within certain limits.Practitioner Points: Disinfectants must maintain a sufficient residual in water distribution systems. Chlorine dioxide requires less contact time and is not affected by pH fluctuations. Modeling serves as a decision‐making tool for the management of disinfectants. Bulk and wall decay rates of chlorine dioxide are crucial for management strategies. Chlorine dioxide is a good alternative as a disinfectant in such systems.
- Open Access
- 19 December 2023
- Published by IWA Publishing in Water Supply
- Vol. 24 (1) , 176-186
A study on pipe failure analysis in water distribution systems using logistic regression
This study presents a pipe failure analysis that aims to identify key factors affecting pipe failure in a pilot study area (PSA). For this purpose, pipe failures that occurred in the PSA were recorded for 2 years. Recorded pipe failures were integrated into the existing geographical information systems of the PSA and then visualized. Then, the logistic regression model that calculates failure probability with unbalanced and small- and medium-sized data was performed to analyze pipe failures. Pipe material, age, diameter, burst pressure, and average water pressure are the factors used in the study. The developed model achieved a success rate of 70.1%, suggesting that it can predict a considerable portion of pipe failures with a relatively satisfactory performance. Findings show that the failure probability of pipes with an age greater than 20 years is 1.675 times higher than that of pipes with an age less than 20 years. Moreover, polyvinyl chloride pipes are 5.265 times and high-density polyethylene pipes are 9.027 times more likely to fail than ductile pipes. Further research should delve into the impacts of the number of service connections, pipe lengths, and traffic load on pipe failures.
- 19 December 2023
- Published by IWA Publishing in Water Supply
- Vol. 24 (1) , 176-186
Open AccessA study on pipe failure analysis in water distribution systems using logistic regression
This study presents a pipe failure analysis that aims to identify key factors affecting pipe failure in a pilot study area (PSA). For this purpose, pipe failures that occurred in the PSA were recorded for 2 years. Recorded pipe failures were integrated into the existing geographical information systems of the PSA and then visualized. Then, the logistic regression model that calculates failure probability with unbalanced and small- and medium-sized data was performed to analyze pipe failures. Pipe material, age, diameter, burst pressure, and average water pressure are the factors used in the study. The developed model achieved a success rate of 70.1%, suggesting that it can predict a considerable portion of pipe failures with a relatively satisfactory performance. Findings show that the failure probability of pipes with an age greater than 20 years is 1.675 times higher than that of pipes with an age less than 20 years. Moreover, polyvinyl chloride pipes are 5.265 times and high-density polyethylene pipes are 9.027 times more likely to fail than ductile pipes. Further research should delve into the impacts of the number of service connections, pipe lengths, and traffic load on pipe failures.
- 31 May 2022
- Published by Kocaeli Journal of Science and Engineering in Kocaeli Journal of Science and Engineering
- Vol. 5 (1) , 42-53
Arsenic Removal Technologies: Mapping Global Research Activities (1970-2019)
Arsenic contamination in drinking water poses worldwide threat to public health and requires emergency actions in some parts of the world. Several technologies have been used to overcome arsenic contamination issues and to meet the arsenic concentration limitations for public health. In this study, research tendencies on arsenic removal technologies were evaluated. A total of 4083 publications, published between 1970 and 2019, on arsenic removal from drinking water, groundwater and wastewater were retrieved from Web of Science (WoS) database. A bibliometric analysis was carried out and word frequency along with visualization map analysis were used to provide a quantitative analysis, and an overview on the current research trends and research prospects. The results showed that annual output of the “arsenic removal” subject increased significantly after the year 2000. “Article” was the most preferable publication type, and “Journal of Hazardous Materials” had the highest publication number. The most productive country in terms of number of total articles on arsenic removal was China. Also, the South-East Asian countries highly contributed to the literature. “Adsorption” was found to be the most frequently researched arsenic removal technology and nanotechnology plays a significant role in the adsorption development.
- 31 May 2022
- Published by Kocaeli Journal of Science and Engineering in Kocaeli Journal of Science and Engineering
- Vol. 5 (1) , 42-53
Arsenic Removal Technologies: Mapping Global Research Activities (1970-2019)
Arsenic contamination in drinking water poses worldwide threat to public health and requires emergency actions in some parts of the world. Several technologies have been used to overcome arsenic contamination issues and to meet the arsenic concentration limitations for public health. In this study, research tendencies on arsenic removal technologies were evaluated. A total of 4083 publications, published between 1970 and 2019, on arsenic removal from drinking water, groundwater and wastewater were retrieved from Web of Science (WoS) database. A bibliometric analysis was carried out and word frequency along with visualization map analysis were used to provide a quantitative analysis, and an overview on the current research trends and research prospects. The results showed that annual output of the “arsenic removal” subject increased significantly after the year 2000. “Article” was the most preferable publication type, and “Journal of Hazardous Materials” had the highest publication number. The most productive country in terms of number of total articles on arsenic removal was China. Also, the South-East Asian countries highly contributed to the literature. “Adsorption” was found to be the most frequently researched arsenic removal technology and nanotechnology plays a significant role in the adsorption development.
- 26 March 2022
- Published by Springer Nature
- p. 53-65
Water Losses Management in Urban Water Distribution Systems
- 26 March 2022
- Published by Springer Nature
- p. 53-65
Water Losses Management in Urban Water Distribution Systems