Bahman Mohammadi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Bahman Mohammadi has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Javad Nourinia
Department of Electrical Engineering, Urmia University, Urmia, Iran
55 shared publications Ch. Ghobadi
Urmia Univ, Dept Elect Engn, Orumiyeh 57153, Iran
22 shared publications- Changiz Ghobadi
Department of Electrical Engineering, Urmia University, Urmia, Iran
22 shared publications - Mohsen Karamirad
Department of Electrical Engineering, Urmia University, Urmia, Iran
15 shared publications - Farzad Alizadeh
Department of E. E, Urmia University, Urmia, Iran
7 shared publications - Mubarak Sani Ellis
Department of Telecommunication Engineering, Kwame Nkrumah University of Science and Technology, Kumasi AK-448-4944, Ghana
7 shared publications
Latest Publications
- 6 July 2022
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 64 (11) , 2075-2082
Compact planar ultra‐wideband pattern diversity antenna
A two‐port planar ultra‐wideband (UWB) pattern diversity antenna is proposed in this letter. The design consists of an array of two rotated identical monopole antennas and two feeding ports with 0° in‐phase and 180° out‐of‐phase excitations. The single monopole antenna includes a circular patch, a rectangular truncated ground plane and a fork‐shaped feeding structure. In this antenna, a modified partial common ground plane is used to enhance the input matching, increase the isolation between antenna elements and improve the desired radiations. The measured results show an |S11| < −10 dB bandwidth ranging from 2 to over 20GHz, with conical and broadside beams, high efficiency, and good isolation across the entire UWB band. Also, the proposed antenna exhibits a smaller footprint, larger bandwidth, and more straightforward design compared with the existing designs. To the best of authors’ knowledge, all these characteristics have never been presented in previously reported UWB pattern diversity antennas.
- 6 July 2022
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 64 (11) , 2075-2082
Compact planar ultra‐wideband pattern diversity antenna
A two‐port planar ultra‐wideband (UWB) pattern diversity antenna is proposed in this letter. The design consists of an array of two rotated identical monopole antennas and two feeding ports with 0° in‐phase and 180° out‐of‐phase excitations. The single monopole antenna includes a circular patch, a rectangular truncated ground plane and a fork‐shaped feeding structure. In this antenna, a modified partial common ground plane is used to enhance the input matching, increase the isolation between antenna elements and improve the desired radiations. The measured results show an |S11| < −10 dB bandwidth ranging from 2 to over 20GHz, with conical and broadside beams, high efficiency, and good isolation across the entire UWB band. Also, the proposed antenna exhibits a smaller footprint, larger bandwidth, and more straightforward design compared with the existing designs. To the best of authors’ knowledge, all these characteristics have never been presented in previously reported UWB pattern diversity antennas.
- 20 December 2020
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 69 (3) , 1283-1293
A Novel Eye-shaped Monopole Antenna for Wideband and 5G Applications
This paper presents a compact dual-band monopole antenna printed on the low-cost FR4 substrate for multi wireless communication applications. The novel antenna consists of an eye-shaped patch and a semicircular shaped slot on the half elliptical ground plane. The antenna’s measurement results include multiband frequencies such as S, C, X, Ku, K, and Ka-band, which covers the bandwidth requirements of WiMAX, WLAN, satellite TV, and 5G applications at the lower and upper-frequency band. The dimension of the antenna is (26 × 20 × 1.6) mm3 at the minimum frequency of 3.15 GHz. The proposed configuration operates at 3.55 and 19.95 GHz with a bandwidth of about 28.17% (3.15–4.15 GHz) and 147.37% (5.25–34.65 GHz), respectively, for the simulation part. The measured bandwidth (−10 dB) for S11 in the lower and upper band is about 49.71% (2.688–4.506 GHz) and 152.01% (4.933–35.861 GHz) at a centre frequency of 3.657 and 20.346 GHz, respectively. The proposed antenna has a stability of the radiation characteristics, suitable gain, and good impedance across the operating bandwidth of the dual-band antenna.
- 20 December 2020
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 69 (3) , 1283-1293
A Novel Eye-shaped Monopole Antenna for Wideband and 5G Applications
This paper presents a compact dual-band monopole antenna printed on the low-cost FR4 substrate for multi wireless communication applications. The novel antenna consists of an eye-shaped patch and a semicircular shaped slot on the half elliptical ground plane. The antenna’s measurement results include multiband frequencies such as S, C, X, Ku, K, and Ka-band, which covers the bandwidth requirements of WiMAX, WLAN, satellite TV, and 5G applications at the lower and upper-frequency band. The dimension of the antenna is (26 × 20 × 1.6) mm3 at the minimum frequency of 3.15 GHz. The proposed configuration operates at 3.55 and 19.95 GHz with a bandwidth of about 28.17% (3.15–4.15 GHz) and 147.37% (5.25–34.65 GHz), respectively, for the simulation part. The measured bandwidth (−10 dB) for S11 in the lower and upper band is about 49.71% (2.688–4.506 GHz) and 152.01% (4.933–35.861 GHz) at a centre frequency of 3.657 and 20.346 GHz, respectively. The proposed antenna has a stability of the radiation characteristics, suitable gain, and good impedance across the operating bandwidth of the dual-band antenna.
- 18 January 2020
- Published by Hindawi Limited in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 30 (5)
Asymmetric circularly polarized open‐slot antenna
A circularly polarized printed antenna using an asymmetric open‐slot is designed in this paper. The presented antenna consists of conducting ground plane with open wide‐slot, fed electromagnetically by a microstrip feedline. The slot and feedline are positioned at the edge of the ground plane and substrate, hence making the antenna asymmetric. The measured results show that the |S11| < −10 dB impedance bandwidth is 125% (3.2‐14 GHz) and the broadband axial ratio bandwidth is 61% (3.2‐6 GHz). The antenna is very simple and has a small size of 25 mm × 25 mm, making it attractive for compact wireless WLAN, ISM, WiMAX, and C‐band applications.
- 18 January 2020
- Published by Hindawi Limited in International Journal of RF and Microwave Computer-Aided Engineering
- Vol. 30 (5)
Asymmetric circularly polarized open‐slot antenna
A circularly polarized printed antenna using an asymmetric open‐slot is designed in this paper. The presented antenna consists of conducting ground plane with open wide‐slot, fed electromagnetically by a microstrip feedline. The slot and feedline are positioned at the edge of the ground plane and substrate, hence making the antenna asymmetric. The measured results show that the |S11| < −10 dB impedance bandwidth is 125% (3.2‐14 GHz) and the broadband axial ratio bandwidth is 61% (3.2‐6 GHz). The antenna is very simple and has a small size of 25 mm × 25 mm, making it attractive for compact wireless WLAN, ISM, WiMAX, and C‐band applications.
- 1 November 2019
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 14 (11) , P11026
Compact broadband circularly polarized printed antenna with a shifted monopole and modified ground plane
- 1 November 2019
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 14 (11) , P11026
Compact broadband circularly polarized printed antenna with a shifted monopole and modified ground plane
- 10 September 2019
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 62 (1) , 405-410
Simple circularly polarized planar monopole inverted T‐shaped antenna
This article presents a novel planar monopole antenna with circular polarization. The 3‐dB axial ratio (AR) is achieved by: shifting a vertical monopole to the left edge of the substrate in conjunction with a laterally inverted L‐shaped ground plane. When viewed from the top, the antenna resembles an uneven T‐shaped structure rotated at 90°. Measurement results show that; a 3‐dB AR bandwidth is achieved from 3.1 to 6.2 GHz (66.7% fractional bandwidth) and an S11 ≤ −10 dB bandwidth is realized from 2.5 to 6.5 GHz (88.9% fractional bandwidth). The proposed antenna is compact with an area of 20 mm2, produces stable radiation patterns, and its simple to design and fabricate without using parasitic elements or introducing slots on the antenna.
- 10 September 2019
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 62 (1) , 405-410
Simple circularly polarized planar monopole inverted T‐shaped antenna
This article presents a novel planar monopole antenna with circular polarization. The 3‐dB axial ratio (AR) is achieved by: shifting a vertical monopole to the left edge of the substrate in conjunction with a laterally inverted L‐shaped ground plane. When viewed from the top, the antenna resembles an uneven T‐shaped structure rotated at 90°. Measurement results show that; a 3‐dB AR bandwidth is achieved from 3.1 to 6.2 GHz (66.7% fractional bandwidth) and an S11 ≤ −10 dB bandwidth is realized from 2.5 to 6.5 GHz (88.9% fractional bandwidth). The proposed antenna is compact with an area of 20 mm2, produces stable radiation patterns, and its simple to design and fabricate without using parasitic elements or introducing slots on the antenna.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1627-1631
RCS Reduction of Reflectarray Antenna Backed with Sub-Wavelength Frequency Selective Surface
A reflectarray antenna (RA) with a novel sub-wavelength-frequency selective surface (FSS) is introduced as a ground plane. The unit element consists of two concentric circular rings, where the width of the outer ring is constant and the width of the inner ring varies. The proposed multi-resonance sub-wavelength element has a linear reflection phase and improved element loss, which results in increased bandwidth and improved aperture efficiency. The triple-connected C-shaped resonator as FSS is used in each unit element instead of the ground plane, so that it is reflective in the frequency range of 9.42-12.55GHz and is transparent outside the working frequency band of the antenna. The reflective and pattern characteristics of the unit elements with the solid-metal and FSS ground planes are compared with each other. The proposed FSS-backed RA has a peak gain of 26.26dBi at 10GHz with a 42.87% aperture efficiency and 15.4% 1dB gain bandwidth. The gain of RA with the FSS ground plane is 0.3 dB lower than the RA with a solid-metal ground plane, while their 1dB gain bandwidth is almost equal.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1627-1631
RCS Reduction of Reflectarray Antenna Backed with Sub-Wavelength Frequency Selective Surface
A reflectarray antenna (RA) with a novel sub-wavelength-frequency selective surface (FSS) is introduced as a ground plane. The unit element consists of two concentric circular rings, where the width of the outer ring is constant and the width of the inner ring varies. The proposed multi-resonance sub-wavelength element has a linear reflection phase and improved element loss, which results in increased bandwidth and improved aperture efficiency. The triple-connected C-shaped resonator as FSS is used in each unit element instead of the ground plane, so that it is reflective in the frequency range of 9.42-12.55GHz and is transparent outside the working frequency band of the antenna. The reflective and pattern characteristics of the unit elements with the solid-metal and FSS ground planes are compared with each other. The proposed FSS-backed RA has a peak gain of 26.26dBi at 10GHz with a 42.87% aperture efficiency and 15.4% 1dB gain bandwidth. The gain of RA with the FSS ground plane is 0.3 dB lower than the RA with a solid-metal ground plane, while their 1dB gain bandwidth is almost equal.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1606-1610
A Novel Compact Triple Band ACS-Fed Antenna
A novel compact triple band asymmetric coplanar strip (ACS)-fed antenna is presented. The offered triple-band antenna is consist of a ACS-fed monopole antenna and two open-ended stepped slots loaded with complementary right-left handed (CRLH) component with different lengths which yield the excitation of three independent resonances as well as antenna size miniaturization. Moreover, to improve the impedance matching in different operating frequency bands, stepped structure is selected for the feed line, ground plane, and radiation patch. The measured| S 11 |<;-10 dB confirms the antenna performance at 5.11-6.32 GHz, 3.39-3.73 GHz and 1.83-2.73 GHz which cover the in-service frequency bands of PCS1900, WLAN, WiMAX, LTE, DMB, ISM, UMTS, HIPERLAN2 and RFID.
- 1 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1606-1610
A Novel Compact Triple Band ACS-Fed Antenna
A novel compact triple band asymmetric coplanar strip (ACS)-fed antenna is presented. The offered triple-band antenna is consist of a ACS-fed monopole antenna and two open-ended stepped slots loaded with complementary right-left handed (CRLH) component with different lengths which yield the excitation of three independent resonances as well as antenna size miniaturization. Moreover, to improve the impedance matching in different operating frequency bands, stepped structure is selected for the feed line, ground plane, and radiation patch. The measured| S 11 |<;-10 dB confirms the antenna performance at 5.11-6.32 GHz, 3.39-3.73 GHz and 1.83-2.73 GHz which cover the in-service frequency bands of PCS1900, WLAN, WiMAX, LTE, DMB, ISM, UMTS, HIPERLAN2 and RFID.
- 5 March 2019
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 61 (6) , 1445-1448
High efficient multi‐bands circular polarization convertor based on spoof surface plasmon polariton
In this paper, we propose to achieve a high efficient polarization convertor based on spoof surface plasmon polariton (SSPP). The proposed polarization convertor is realized by a dielectric blade with a metallic pattern on one side. Spatial dispersion modulation is considered by designing the pattern in y‐direction while keeping free space in x‐direction. Meanwhile, the y‐polarized incident wave is well coupled as SSPP mode. Therefore, the circular polarization (CP) conversion is provided regarding to the direction of the incident waves. A frequency bandwidth of 52.7% is obtained for right to left CP while left to right polarization conversion is adopted in a 23% bandwidth. The fabricated prototype of the proposed structure is provided to verify the simulated results.
- 5 March 2019
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 61 (6) , 1445-1448
High efficient multi‐bands circular polarization convertor based on spoof surface plasmon polariton
In this paper, we propose to achieve a high efficient polarization convertor based on spoof surface plasmon polariton (SSPP). The proposed polarization convertor is realized by a dielectric blade with a metallic pattern on one side. Spatial dispersion modulation is considered by designing the pattern in y‐direction while keeping free space in x‐direction. Meanwhile, the y‐polarized incident wave is well coupled as SSPP mode. Therefore, the circular polarization (CP) conversion is provided regarding to the direction of the incident waves. A frequency bandwidth of 52.7% is obtained for right to left CP while left to right polarization conversion is adopted in a 23% bandwidth. The fabricated prototype of the proposed structure is provided to verify the simulated results.
- 1 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 124-127
Novel Broadband 3U CubeSat Reflectarray Antenna
A novel broadband reflectarray (RA) antenna for 3U CubeSat applications is investigated. A novel frequency selective surface (FSS) in the RA as ground plane for reducing radar cross section (RCS) and signals interference with other communication systems working in other frequency bands is applied. The RA divided to three panels and folded on the sides of the CubeSat to reduce the stowed volume. A novel circular polarization (CP) feed antenna with two stacked patches on two thick substrates with lossy dielectric constant is used to extend the 3dB axial ratio.
- 1 February 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 124-127
Novel Broadband 3U CubeSat Reflectarray Antenna
A novel broadband reflectarray (RA) antenna for 3U CubeSat applications is investigated. A novel frequency selective surface (FSS) in the RA as ground plane for reducing radar cross section (RCS) and signals interference with other communication systems working in other frequency bands is applied. The RA divided to three panels and folded on the sides of the CubeSat to reduce the stowed volume. A novel circular polarization (CP) feed antenna with two stacked patches on two thick substrates with lossy dielectric constant is used to extend the 3dB axial ratio.