Liuyi Ren
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Liuyi Ren has a total of 75 co-authors. Here are the top co-authors by number of shared publications:
Yimin Zhang
17 shared publications- Shenxu Bao
Key Laboratory of Green Utilization of Critical Non-Metallic Mineral Resources, Ministry of Education, Wuhan University of Technology, Wuhan 430070, China
13 shared publications Shenxu Bao
12 shared publications- Anh V. Nguyen
School of Chemical Engineering and ARC Centre of Excellence for Enabling Eco-Efficient Beneficiation of Minerals (UQ Node), The University of Queensland, Brisbane, QLD 4072, Australia
7 shared publications - Yimin Zhang
School of Resource and Environmental Engineering, Wuhan University of Science and Technology, Wuhan 430081, China
5 shared publications Pengfei Song
4 shared publications
Latest Publications
- Open Access
- 23 October 2026
- Published by Elsevier in SSRN Electronic Journal
Reverse Flotation Demagnesiation Performance and Selective Adsorption Mechanism of the Gemini-Type Dicarboxylic Fatty Acid Collector HQ-01 for Calcareous-Magnesian Collophanite
Conventional fatty acid collectors exhibit limited selectivity in the reverse flotation of calcareous-magnesian collophanite ores. In this study, a Gemini-type surfactant (HQ-01) featuring two hydrophobic chains and two carboxyl groups was employed as a novel collector. Its demagnesiation performance was evaluated through single-mineral, artificial mixed-mineral, and actual ore flotation tests, while zeta potential, FTIR, and XPS analyses were conducted to investigate its selective adsorption mechanism. The results demonstrated that HQ-01 exhibited strong selectivity toward dolomite under weakly acidic conditions. In mixed-mineral flotation, fluorapatite recovery exceeded 80%, whereas dolomite recovery remained below 10% at HQ-01 dosages of 600–800 g/t. In actual ore flotation, an open-circuit flowsheet comprising one roughing and one cleaning stage produced a low-magnesium phosphate concentrate with a P2O5 grade of 30.51%, P2O5 recovery of 70.59%, and MgO content of 1.32%, outperforming conventional sodium oleate. Zeta potential, FTIR, and XPS analyses indicated preferential adsorption of HQ-01 on dolomite. After treatment, pronounced changes were observed in the C 1s, O 1s, and Mg 1s spectra of dolomite, whereas the Ca 2p spectrum showed only minor changes. These findings suggested that the carboxyl groups of HQ-01 may preferentially interact with surface Mg active sites, enhancing dolomite hydrophobicity and facilitating selective separation from fluorapatite. This study provides new insights into the development of Gemini-type flotation collectors and supports their potential application in phosphate ore demagnesiation.
- 23 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessReverse Flotation Demagnesiation Performance and Selective Adsorption Mechanism of the Gemini-Type Dicarboxylic Fatty Acid Collector HQ-01 for Calcareous-Magnesian Collophanite
Conventional fatty acid collectors exhibit limited selectivity in the reverse flotation of calcareous-magnesian collophanite ores. In this study, a Gemini-type surfactant (HQ-01) featuring two hydrophobic chains and two carboxyl groups was employed as a novel collector. Its demagnesiation performance was evaluated through single-mineral, artificial mixed-mineral, and actual ore flotation tests, while zeta potential, FTIR, and XPS analyses were conducted to investigate its selective adsorption mechanism. The results demonstrated that HQ-01 exhibited strong selectivity toward dolomite under weakly acidic conditions. In mixed-mineral flotation, fluorapatite recovery exceeded 80%, whereas dolomite recovery remained below 10% at HQ-01 dosages of 600–800 g/t. In actual ore flotation, an open-circuit flowsheet comprising one roughing and one cleaning stage produced a low-magnesium phosphate concentrate with a P2O5 grade of 30.51%, P2O5 recovery of 70.59%, and MgO content of 1.32%, outperforming conventional sodium oleate. Zeta potential, FTIR, and XPS analyses indicated preferential adsorption of HQ-01 on dolomite. After treatment, pronounced changes were observed in the C 1s, O 1s, and Mg 1s spectra of dolomite, whereas the Ca 2p spectrum showed only minor changes. These findings suggested that the carboxyl groups of HQ-01 may preferentially interact with surface Mg active sites, enhancing dolomite hydrophobicity and facilitating selective separation from fluorapatite. This study provides new insights into the development of Gemini-type flotation collectors and supports their potential application in phosphate ore demagnesiation.
- 9 September 2026
- Published by Elsevier in Colloids and Surfaces A: Physicochemical and Engineering Aspects
- Vol. 752
Inhibition mechanism of Fe3 + on the separation of quartz and gypsum in CTAC flotation
- 9 September 2026
- Published by Elsevier in Colloids and Surfaces A: Physicochemical and Engineering Aspects
- Vol. 752
Inhibition mechanism of Fe3 + on the separation of quartz and gypsum in CTAC flotation
- 8 July 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (28) , 20805-20813
Synergistic Impact of Turkey Red Oil and Sodium Oleate on the Separation of Dolomite from Apatite
Dolomite and apatite exhibit very similar surface chemical properties, while conventional fatty acid collectors show limited selectivity between them, making their efficient separation in phosphate rock flotation a persistent challenge. In this study, a mixed collector system (RF-25), composed mainly of sodium oleate (NaOL) and turkey red oil (TRO), was designed to enhance the separation of dolomite from apatite via reverse flotation. Micro-flotation experiments indicated that the optimal separation performance was obtained at pH 5, with an H3PO4 concentration of 8 × 10-4 mol L-1 and a NaOL:TRO ratio of 4:1. Under these conditions, when the collector concentration was 60 mg L-1, the recovery rates of dolomite and apatite differed by 90.09 percentage points. The results of mixed-mineral flotation further demonstrated the effectiveness of RF-25, where P2O5 recovery reached 95.71% while MgO recovery was reduced to 19.79%. Surface characterization analyses provided insight into the improved selectivity mechanism. TOC and contact angle measurements showed that RF-25 preferentially adsorbed onto dolomite, significantly increasing its surface hydrophobicity compared with that of apatite. FTIR and XPS results further confirmed that a more continuous and complete adsorption layer formed on the dolomite surface, whereas only weak adsorption occurred on apatite. Zeta potential measurements were consistent with these findings, indicating a more pronounced surface modification of dolomite after treatment with RF-25. Overall, the mixed collector enhanced the difference in interfacial properties between dolomite and apatite, thereby improving flotation selectivity. This work demonstrated that RF-25 provided an effective strategy for the selective removal of Mg-bearing gangue minerals in phosphate rock flotation.
- 8 July 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (28) , 20805-20813
Synergistic Impact of Turkey Red Oil and Sodium Oleate on the Separation of Dolomite from Apatite
Dolomite and apatite exhibit very similar surface chemical properties, while conventional fatty acid collectors show limited selectivity between them, making their efficient separation in phosphate rock flotation a persistent challenge. In this study, a mixed collector system (RF-25), composed mainly of sodium oleate (NaOL) and turkey red oil (TRO), was designed to enhance the separation of dolomite from apatite via reverse flotation. Micro-flotation experiments indicated that the optimal separation performance was obtained at pH 5, with an H3PO4 concentration of 8 × 10-4 mol L-1 and a NaOL:TRO ratio of 4:1. Under these conditions, when the collector concentration was 60 mg L-1, the recovery rates of dolomite and apatite differed by 90.09 percentage points. The results of mixed-mineral flotation further demonstrated the effectiveness of RF-25, where P2O5 recovery reached 95.71% while MgO recovery was reduced to 19.79%. Surface characterization analyses provided insight into the improved selectivity mechanism. TOC and contact angle measurements showed that RF-25 preferentially adsorbed onto dolomite, significantly increasing its surface hydrophobicity compared with that of apatite. FTIR and XPS results further confirmed that a more continuous and complete adsorption layer formed on the dolomite surface, whereas only weak adsorption occurred on apatite. Zeta potential measurements were consistent with these findings, indicating a more pronounced surface modification of dolomite after treatment with RF-25. Overall, the mixed collector enhanced the difference in interfacial properties between dolomite and apatite, thereby improving flotation selectivity. This work demonstrated that RF-25 provided an effective strategy for the selective removal of Mg-bearing gangue minerals in phosphate rock flotation.
- 28 June 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (27) , 20066-20075
Elimination of Sodium Hexametaphosphate Depression on Fluorite Flotation by Lead Ions
Fluorite is a vital strategic nonmetallic mineral resource. In the processing of complex associated fluorite ores, it is typically recovered from flotation tailings. However, its flotation performance is severely depressed by residual sodium hexametaphosphate (SHMP) from upstream flotation operations. In this study, Pb2+ was adopted as a high-efficiency activator to reverse the depression of SHMP on fluorite flotation, with octyl hydroxamic acid (OHA) as the collector. Microflotation results showed that Pb2+ significantly restored the floatability of SHMP-depressed fluorite, increasing its recovery from only 1.11% to 90.63%. Mechanism studies confirmed a synergistic activation pathway: "liquid-phase consumption and solid-phase reconstruction". In the liquid phase, Pb2+ reacted with free SHMP to form Pb-SHMP coprecipitates, thus reducing the depressant concentration in the pulp. On the solid surface, adsorbed Pb-SHMP precipitates and hydrolyzed lead species acted as new active sites for OHA anions.
- 28 June 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (27) , 20066-20075
Elimination of Sodium Hexametaphosphate Depression on Fluorite Flotation by Lead Ions
Fluorite is a vital strategic nonmetallic mineral resource. In the processing of complex associated fluorite ores, it is typically recovered from flotation tailings. However, its flotation performance is severely depressed by residual sodium hexametaphosphate (SHMP) from upstream flotation operations. In this study, Pb2+ was adopted as a high-efficiency activator to reverse the depression of SHMP on fluorite flotation, with octyl hydroxamic acid (OHA) as the collector. Microflotation results showed that Pb2+ significantly restored the floatability of SHMP-depressed fluorite, increasing its recovery from only 1.11% to 90.63%. Mechanism studies confirmed a synergistic activation pathway: "liquid-phase consumption and solid-phase reconstruction". In the liquid phase, Pb2+ reacted with free SHMP to form Pb-SHMP coprecipitates, thus reducing the depressant concentration in the pulp. On the solid surface, adsorbed Pb-SHMP precipitates and hydrolyzed lead species acted as new active sites for OHA anions.
- Open Access
- 6 March 2026
- Published by Elsevier in SSRN Electronic Journal
Enhanced Flotation Separation of Quartz from Phlogopite via Phlogopite-Dissolved Calcium Ions Activation
Flotation, a widely used mineral separation technique, is influenced by the chemical environment of the pulp, which often contains a variety of dissolved metal ions. These ions can have both positive and negative impacts on the flotation process. In silicate flotation systems, certain metal ions are released from minerals, potentially modifying surface properties and altering the flotation behavior of minerals. This study explores the role of calcium ions in the flotation separation of phlogopite and quartz, focusing on how these ions affect the adsorption capacity of collectors and influence flotation recovery. Calcium ions, released from phlogopite during flotation, were found to significantly enhance the adsorption of collectors on the quartz surface, improving flotation recovery, especially under alkaline conditions. The sequence of calcium ion interaction with the mineral surfaces plays a crucial role in the flotation process, with prior exposure to calcium ions providing a stronger activation effect. The optimal flotation performance was achieved using a mixed collector system (DDA-NaOL) at pH 8, which demonstrated a recovery difference of 59.19% between phlogopite and quartz. These findings highlight the activation role of calcium ions in improving flotation selectivity and offer valuable insights into the underlying mechanisms of calcium ion activation in flotation processes.
- 6 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEnhanced Flotation Separation of Quartz from Phlogopite via Phlogopite-Dissolved Calcium Ions Activation
Flotation, a widely used mineral separation technique, is influenced by the chemical environment of the pulp, which often contains a variety of dissolved metal ions. These ions can have both positive and negative impacts on the flotation process. In silicate flotation systems, certain metal ions are released from minerals, potentially modifying surface properties and altering the flotation behavior of minerals. This study explores the role of calcium ions in the flotation separation of phlogopite and quartz, focusing on how these ions affect the adsorption capacity of collectors and influence flotation recovery. Calcium ions, released from phlogopite during flotation, were found to significantly enhance the adsorption of collectors on the quartz surface, improving flotation recovery, especially under alkaline conditions. The sequence of calcium ion interaction with the mineral surfaces plays a crucial role in the flotation process, with prior exposure to calcium ions providing a stronger activation effect. The optimal flotation performance was achieved using a mixed collector system (DDA-NaOL) at pH 8, which demonstrated a recovery difference of 59.19% between phlogopite and quartz. These findings highlight the activation role of calcium ions in improving flotation selectivity and offer valuable insights into the underlying mechanisms of calcium ion activation in flotation processes.
- 18 February 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (8) , 6560-6569
Mechanism of Alkali-Gelatinized Soluble Starch as a Depressant for Fluorite–Dolomite Flotation Separation
Flotation separation of fluorite from dolomite is challenging due to their similar surface properties. In this study, neutralized alkali-gelatinized soluble starch (NAGS) was used as a flotation depressant. NAGS was prepared by gelatinizing soluble starch in an alkaline solution, followed by pH neutralization. The depressive performance and mechanism of NAGS in the fluorite-dolomite flotation separation were systematically investigated. Microflotation tests showed that, at pH 7 with a sodium oleate (NaOL) concentration of 30 mg/L and NAGS concentration of 100 mg/L, the recovery difference between fluorite and dolomite in single-mineral flotation reached as high as 95.10%. In the flotation concentrate of the artificially mixed mineral, the fluorite grade was 87.09%, and the fluorite recovery was 90.12%. NAGS exhibited a pronounced selective depressive effect on dolomite, which was further confirmed by contact angle measurements. Zeta potential measurements, Adsorption capacity measurements, Fourier-transform infrared (FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS) were combined to elucidate the adsorption mechanism of NAGS. Collectively, NAGS adsorbs on both mineral surfaces via physisorption but with distinct dominant forces: electrostatic interactions predominate on fluorite, while hydrogen bonding is predominant on dolomite. This differential adsorption strength explains the selective depression of dolomite.
- 18 February 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (8) , 6560-6569
Mechanism of Alkali-Gelatinized Soluble Starch as a Depressant for Fluorite–Dolomite Flotation Separation
Flotation separation of fluorite from dolomite is challenging due to their similar surface properties. In this study, neutralized alkali-gelatinized soluble starch (NAGS) was used as a flotation depressant. NAGS was prepared by gelatinizing soluble starch in an alkaline solution, followed by pH neutralization. The depressive performance and mechanism of NAGS in the fluorite-dolomite flotation separation were systematically investigated. Microflotation tests showed that, at pH 7 with a sodium oleate (NaOL) concentration of 30 mg/L and NAGS concentration of 100 mg/L, the recovery difference between fluorite and dolomite in single-mineral flotation reached as high as 95.10%. In the flotation concentrate of the artificially mixed mineral, the fluorite grade was 87.09%, and the fluorite recovery was 90.12%. NAGS exhibited a pronounced selective depressive effect on dolomite, which was further confirmed by contact angle measurements. Zeta potential measurements, Adsorption capacity measurements, Fourier-transform infrared (FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS) were combined to elucidate the adsorption mechanism of NAGS. Collectively, NAGS adsorbs on both mineral surfaces via physisorption but with distinct dominant forces: electrostatic interactions predominate on fluorite, while hydrogen bonding is predominant on dolomite. This differential adsorption strength explains the selective depression of dolomite.
- 10 October 2025
- Published by Elsevier in Colloids and Surfaces A: Physicochemical and Engineering Aspects
- Vol. 728
Optimizing cetyl trimethyl ammonium chloride for phosphogypsum purification mechanism
- 10 October 2025
- Published by Elsevier in Colloids and Surfaces A: Physicochemical and Engineering Aspects
- Vol. 728
Optimizing cetyl trimethyl ammonium chloride for phosphogypsum purification mechanism